GB/T 31062-2014 PDF EnglishUS$155.00 · In stock · Download in 9 seconds
GB/T 31062-2014: Polymeric polyols Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 31062-2014: Polymeric polyols---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT31062-2014NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.040 G 32 Polymeric polyols 聚合物多元醇 ISSUED ON: DECEMBER 22, 2014 IMPLEMENTED ON: JUNE 01, 2015 Issued by: General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Naming rules ... 4 4 Requirements ... 6 5 Test methods ... 7 6 Inspection rules ... 12 7 Marks, packaging, transport, storage ... 13 Annex A (informative) Control between new and old specifications of main representative product ... 14 Polymeric polyols1 ScopeThis Standard specifies naming, requirements, test methods, inspection rules, marks, packaging, transport and storage of polymeric polyols. This Standard is applicable to polymer polyols made from polyether polyol and styrene, acrylonitrile, etc.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 6680-2003, General rules for sampling liquid chemical products GB/T 8170-2008, Rules of rounding off for numerical values & expression and judgement of limiting values GB/T 12008.2-2010, Plastics - Polyether polyols - Part 2: Specification GB/T 12008.3-2009, Plastics - Polyether polyols - Part 3: Determination of hydroxyl number GB/T 12008.5-2010, Plastics - Polyether polyols - Part 5: Determination of acidity as acid number GB/T 12008.7-2010, Plastics - Polyether polyols - Part 7: Determination of viscosity GB/T 22313-2008, Plastics - Polyols for use in the production of polyurethane - Determination of water content3 Naming rules3.1 Naming of polymeric polyols The naming of polymeric polyols consists of fixed name and feature item. The fixed name is polymer polyol, which is referred to as POP. The feature item5 Test methods5.1 Determination of appearance Load 50mLof sample into a 50mL colorimetric tube. Observe from the side. 5.2 Determination of hydroxyl value Carry out according to the method specified in GB/T 12008.3-2009. Use Method A as the arbitration method. The sampling weighing amount is half of the amount specified in 4.5.1 of GB/T 12008.3-2009. In 4.5.2 of GB/T 12008.3-2009, after accurately weighing 25mLof phthalic anhydride acylating reagent to each test material and blank Erlenmeyer flask, add 50mL of pyridine. 5.3 Determination of water mass fraction Carry out according to the method specified in GB/T 22313-2008. 5.4 Determination of viscosity Carry out according to Method B specified in GB/T 12008.7-2010. 5.5 Determination of acid value Carry out according to the method specified in GB/T 12008.5-2010. 5.6 Determination of pH value Carry out according to the method specified in Annex B of GB/T 12008.2-2010. 5.7 Determination of solid content 5.7.1 Method summary The non-solid components in the sample are washed by ethanol solution and separated under centrifugal force. After they are dried in a vacuum thermostat, weigh and calculate the solid content of polymer polyol. 5.7.2 Instruments and materials This method uses the following instruments and materials: a) High-speed centrifuge: 0r/min~16500r/min; b) Anhydrous ethanol: analytical reagent; c) Graduated pipette: 25mL; d) Vacuum drying box: -0.1MPa; 5.8.2 Instruments and equipment This method uses the following instruments and equipment: a) Gas chromatograph: equipped with data processing device or chromatography workstation, equipped with hydrogen flame detector (FID); capillary split / split-less sample inlet; b) Automatic headspace sample injector: 2.5mL or 1mL, graduation value is 0.001mL; c) Headspace bottle: 20mL; equipped with silicone pad that is coated with tetrafluoroethylene on both sides and aluminum cover; d) Analytical balance: resolution is 0.1mg; e) Glass syringe: 1mL; f) Polyethylene bottle: 100mL; g) Oscillator; h) Vacuum pump; i) Heater. 5.8.3 Test conditions 5.8.3.1 Headspace conditions The headspace conditions of this Method are: a) Headspace temperature: 120°C; b) Headspace time: 20min; c) Sample mass: 2g. 5.8.3.2 Chromatographic working conditions The chromatographic working conditions of this method are: a) Split / split-less sample inlet temperature: 180°C; b) Column compartment temperature: 120°C; c) Detector temperature: 180°C; d) Chromatographic column: PEG20M, 0.32mm × 30m × 1μm; than 6°C. 2) Standard use solution: In 6 clean, dry 100mL polyethylene bottles, add about 100g of polymeric polyol sample without free acrylonitrile and styrene, to the nearest of 0.0001g. Respectively add 0.5g, 1g, 2g, 3g, 4g, 5g of the above standard stock solution, to the nearest of 0.0001g. Oscillate on the oscillator for 5h. Completely mix well for use. The contents of free acrylonitrile and styrene in this standard use solution are 10mg/kg, 20mg/kg, 40mg/kg, 60mg/kg, 80mg/kg, 100mg/kg. 5.8.5 Determination steps 5.8.5.1 General The samples taken shall be kept in sealed bottles, with little or no headspace. The sample shall be immediately tested when it is loaded in a headspace bottle. 5.8.5.2 Preparation of curve making In 6 pieces of 20mL headspace bottles, respectively add 2g of standard use solution. According to the test conditions of 5.8.3, conduct the headspace analysis. Record the chromatographic peak areas of acrylonitrile and styrene. Respectively take the contents of free acrylonitrile and styrene in the standard use solution as the ordinates, the peak areas of acrylonitrile and styrene as the abscissas to draw a regression curve according to formula (2). Where, y - Value of content of free acrylonitrile or styrene in the standard use solution, in milligrams per kilogram (mg/kg); a - Intercept of regression curve; b - Slope of regression curve; x - Peak area of acrylonitrile or styrene recorded in the standard use solution on the chromatography workstation or data processor. 5.8.5.3 Sample determination Add about 2g of sample in a 20mL headspace bottle, to the nearest of 0.0001g. Immediately seal. Conduct the headspace analysis according to the test conditions of 5.8.3. Record the peak areas of acrylonitrile and styrene. 5.8.6 Result calculation seal. The sample bottles shall be labeled to indicate the product name, specifications, batch number, sampling date and sampling staff. One bottle is for inspection and the other shall be sealed to for storage and future inspection. 6.4 Determination rules and re-inspection rules Use the rounding-off method in GB/T 8170-2008 to round off the test results that have been inspected according to this Standard. If the inspection results meet the requirements of this Standard, it shall be accepted. If one time fails through product inspection, it shall allow re-extract the sample of double quantity from the same batch of products to reinspect the failed item. If the re- inspection results still fail, this batch of products shall be rejected.7 Marks, packaging, transport, storage7.1 Marks There shall be a clear and firm mark on the packaging barrel of the product, indicating: product name, specifications, level, manufacturer name, address, production date, batch number, net mass, storage period, reference to this Standard and quality conformity mark. 7.2 Packaging The packaging container for this product is a clean and dry paint-coated iron drum, or other pattern of clean packaging container. The lid of the packaging container must be tightly sealed with an outer lid. Each batch of products shall be attached with quality certificates. 7.3 Transport This product can be transported by ordinary means of transportation. It shall be lightly loaded, unloaded and not upside down during transport. There shall be measures against moisture, rain, sunlight and collision. 7.4 Storage This product shall be stored in a cool, dry and ventilated warehouse. There shall be measures to prevent sunlight and rain when storing outdoors. Under the storage and transport conditions that comply with the provisions of this Standard, the unopened products shall be stored for one year since the date of production. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 31062-2014 be delivered?Answer: The full copy PDF of English version of GB/T 31062-2014 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 31062-2014_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 31062-2014_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 31062-2014 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 31062-2014?A step-by-step guide to download PDF of GB/T 31062-2014_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 31062-2014". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
