GB/T 29838-2013 PDF EnglishUS$145.00 · In stock · Download in 9 seconds
GB/T 29838-2013: Fuel cell modules Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 29838-2013: Fuel cell modules---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT29838-2013GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 27.070 F 19 Fuel cell modules (IEC 62282-2.2012, MOD) Issued on. NOVEMBER 12, 2013 Implemented on. MARCH 7, 2014 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration Committee. Table of ContentsForeword... 3 1 Scope... 4 2 Normative references... 5 3 Terms and definitions... 6 4 Requirements... 10 5 Type tests... 19 6 Routine tests... 30 7 Markings and instructions... 31 Annex A (informative) Additional information for the performance and evaluation of the tests... 37 Bibliography... 45ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard uses redrafting method to modify and adopt IEC 62282-2 Ed.2.2012 "Fuel cell technologies Part 2.Fuel cell modules". This Standard is technically consistent with IEC 62282-2.2012.The modifications are as follows. - deleted the foreword and introduction of IEC 62282-2.2012, added the foreword of this Standard; - for the normative references, all Chinese standards that correspond to IEC (or ISO) standards are replaced by Chinese standards; - the safety standard in this Standard incorporated Chinese specific safety requirements, added "5.10 Insulation (static) test" in Clause 5 "Type tests". This Standard was proposed by China Electrical Appliance Industry Association. This Standard shall be under the jurisdiction of National Technical Committee on Fuel Cell and Flow Battery of Standardization Administration of China (SAC/TC 342). The drafting organizations of this Standard. Xinyuan Power Co., Ltd., Machinery Industry Beijing Institute of Electrotechnics and Economics, Shanghai Shenli Technology Co., Ltd., Wuhan Yintai Technology Fuel Cell Co., Ltd., Ningbo Baite Measurement & Control Technology Co., Ltd., Wuhan University of Technology, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Shanghai Panye Hydrogen Energy Technology Co., Ltd., Tsinghua University, Tongji University, Kunshan Institute of Innovation, Nanjing University, Shenzhen Huachen Detection Technology Co., Ltd., etc. Main drafters of this Standard. Hou Zhongjun, Li Xiaonan, Tian Chaohe, Zhang Ruogu, Qi Zhigang, Huang Ping, Yan Xiqiang, Chen Chen, Pan Mu, Yi Baolian, Dong Hui, Hou Ming, Pei Pucheng, Hou Yongping, Lu Chenyu, Gu Jun, Zhu Ping, etc. Fuel cell modules1 ScopeThis Standard provides the minimum requirements for safety and performance of fuel cell modules and applies to fuel cell modules with the following electrolyte chemistry.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply. (related to cells/stacks) preliminary step that is required to properly operate a fuel cell module (3.8) and that is realized following a protocol specified by the manufacturer assembly incorporating one or more fuel cell stacks and other main and, if applicable, additional components, which is intended to be integrated into a power system4 RequirementsThe fuel cell module shall be designed in accordance with a risk assessment performed by the fuel cell module manufacturer. All parts shall be The fuel cell module shall be designed in such a way that it withstands all normal operating conditions as defined by the manufacturer’s specification without any damage. Abnormal operating conditions shall be covered according to 4.1.5 Type testsThe fuel cell module shall be subject to the shock and vibration test limits stated in the manufacturer’s documentation. This test is only applicable for enclosed systems, with integrated safety ventilation and purging processes, where the operating temperature is below the auto-ignition temperature of the combustible gas.6 Routine testsDielectric strength tests shall be performed on all production units after assembly. Dielectric strength tests shall be performed as described in 5.9 with a test duration of 1 s at a normal temperature.7 Markings and instructionsIf connections can be interchanged and result in unsafe conditions, they shall be identified. Polarity of the electrical connections and grounding, if applicable, shall be indicated. The information necessary for system integration, installation, operation and maintenance of the fuel cell module shall be supplied in the form of drawings, diagrams, charts, tables and instructions. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 29838-2013 be delivered?Answer: The full copy PDF of English version of GB/T 29838-2013 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 29838-2013_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 29838-2013_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 29838-2013 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 29838-2013?A step-by-step guide to download PDF of GB/T 29838-2013_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 29838-2013". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
