GB/T 28633-2012 English PDFUS$314.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 28633-2012: Surface chemical analysis -- X-ray photoelectron spectroscopy -- Repeatability and constancy of intensity scale Status: Valid
Basic dataStandard ID: GB/T 28633-2012 (GB/T28633-2012)Description (Translated English): Surface chemical analysis -- X-ray photoelectron spectroscopy -- Repeatability and constancy of intensity scale Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: G04 Classification of International Standard: 71.040.40 Word Count Estimation: 16,157 Adopted Standard: ISO 24237-2005, IDT Regulation (derived from): National Standards Bulletin 2012 No. 17 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard provides an assessment routine analysis X-ray photoelectron spectroscopy intensity scale repeatability and consistency of approach, the use of non- monochromatic Al/Mg or monochromatic Al X -ray source. This standard applies only to sputter GB/T 28633-2012: Surface chemical analysis -- X-ray photoelectron spectroscopy -- Repeatability and constancy of intensity scale---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Surface chemical analysis. X-ray photoelectron spectroscopy. Repeatability and constancy of intensity scale ICS 71.040.40 G04 National Standards of People's Republic of China Surface chemical analysis - X-ray photoelectron spectroscopy Repeatability and consistency of intensity scale (ISO 24237.2005, IDT) Issued on. 2012-07-31 2013-02-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsPreface Ⅰ Introduction Ⅱ 1 Scope 1 2 Symbols and Abbreviations 1 3 Summary of Method 1 4 intensity scale assessment of the repeatability and consistency of approach 3 4.1 Get the reference sample 3 4.2 Installation Sample 3 4.3 Cleaning sample 3 4.4 Selective strength stability of the spectrometer parameter setting 4 4.5 Operating equipment 4 4.6 initial or subsequent evaluation measures Option 4 4.7 measuring the intensity and reproducibility of 4 4.8 calculate the peak area intensity, the intensity ratio and uncertainty 5 4.9 General Evaluation intensity scale consistency 5 4.10 reassessed 7 Goods X-ray photoelectron Annex A (informative) non-monochromatic MgKα X-ray spectrometer source of strength and repeatable measurements Calculation Example 8 A.1 symbol 8 A.2 Goods X-ray photoelectron spectroscopy strength repeatability measurements and calculations Example 8 References 11ForewordThis standard was drafted in accordance with GB/T 1.1-2009 given rules. This standard uses the translation method identical with ISO 24237.2005 (E) "Surface chemical analysis - X-ray photoelectron spectroscopy of intensity scale Repeatability and consistency. " The standard micro-beam analysis by the National Standardization Technical Committee (SAC/TC38) and focal points. This standard was drafted. Analysis and Testing Center, Beijing Normal University. The main drafters of this standard. Wu Zhenglong.IntroductionAnalysis of surface X-ray photoelectron spectroscopy (XPS) is widely used material. From the measured photoelectron spectra give each element of the sample surface Within the level of binding energy, the binding energy of the control elements in the sample identification table different elements (except hydrogen and helium). From the measured photoelectron peak intensity Quantitative information can be obtained in these elements. Relative sensitivity factors apply formulas and equipment provided by the manufacturer, it can be quantified. spirit Sensitivity factor is applicable to instruments is essential, usually after the instrument is installed, or in response to the peak intensity of the instrument was calibrated by a competent body/energy After the function, sensitivity factor can be applied directly. In this standard, on the impact of peak intensity XPS measurement uncertainty of two important The instrument factors. Repeatability (1) of the peak intensity measured; (2) peak intensity drifts over time. For the analysis of trends and differences between similar samples, reproducibility is important. Factors affecting the measurement instrumentation repetitive Are. stability, detector X-ray source is provided, the sensitivity of the instrument sample location data acquisition parameters and data processing methods. instrument Intensity scale drift will affect the overall accuracy of the results of any quantitative analysis. This is due to instrument drift component, the electronic control unit And detector aging and other factors. In the XPS instrument, it has been found that the equipment in use, the strength of the instrument/energy response function It varies with the life of the instrument. This standard describes a measuring instrument repeatability and consistency of the underlying strength of a simple method for instrument calibration, such as improved operating step Step, re-set parameters or re-calibrate the instrument intensity/energy response function. Therefore, this method should be repeated periodically testing instruments, if Instrument manufacturer or a qualified agency has checked the equipment to work properly, it is during this period of the present method is very useful. The method uses pure Copper (Cu) sample for non-monochromatic aluminum (Al) or magnesium (of Mg) of the X-ray source X-ray photoelectron spectrometer, monochromator or aluminum (Al) X-ray source X-ray photoelectron spectroscopy. This method is not set forth all possible instrument errors exist, because it is very time-consuming test, and requires specialized knowledge and equipment. But Describes the XPS instrument intensity scale common basic problem that the repeatability and drift. Can be used simultaneously when using this method GB/T 22571-2008 [1] instrument calibration energy. Surface chemical analysis - X-ray photoelectron spectroscopy Repeatability and consistency of intensity scale1 ScopeThis standard specifies the routine analysis method for assessing the strength of the underlying repeatability and consistency of the method of X-ray photoelectron spectroscopy, the use of non Monochromatic Al/Mg or monochrome AlX ray source. This standard applies only to instruments fitted sputter ion gun. This standard is not strength/energy ring It should calibration function. This instrument calibration by the manufacturer or other qualified agencies to complete. This standard provides the data used to assess and confirm the instrument Accuracy response function to maintain a constant strength during use/energy. This standard provides some may affect the consistency of instrument settings instructions.2 Symbols and AbbreviationsThe average peak area A2 after deducting Shirley background Cu2p3/2 peak A component value A2j A2 for j-th measured in a group of measurement values A3 deduction Shirley background, the average peak area Cu3p peak A component value A3j A3 for j-th measured in a group of measurement values Pi i symbol for one of the three parameters of which Subscript j independent measurements of one parameter Pij Pi represents the mean of parameter A2, A3 and the amount of any one of A3/A2 The average of Pi parameters Pij j-th measurement When U95 (Pi) 95% confidence limits mean uncertainty Pi XPS X-ray photoelectron spectroscopy δ 95% confidence limits (set by the analyst) if consistency tolerance value A3/A2 of Energy Δ instrument binding energy scale drift amount, equal to the measured Cu2p3/2 binding energy value of the peak maximum intensity minus 932.7eV σ (Pi) parameter Pi repeatability standard deviation3 Methods SummaryHere is an overview of the method, in order to understand in detail in Chapter 4 steps. Measurement Cu2p3/2 and Cu3pX shot at suitable parameters Ray photoelectron peak intensity, and get ready to foil reference material is necessary in order to evaluate X-ray photoelectron spectrometer by the method reproducibility And consistency. Choose these peaks because they are close to the actual analysis of the binding energy of the high limit and low limit. These peaks are explicitly selected, And a corresponding reference data. The initial step to prepare reference material and instrument parameter settings see 4.1 to 4.5, the flow chart shown in Figure 1, the figure includes the relevant sub-headings. If you have not had the intensity of repetitive measurement, the user needs to enter from 4.6 to 4.7. In 4.7, the measurement sequence is repeated 7 times Strength Cu2p3/2 and Cu3p peaks. These data are given the repeatability standard deviation of the peak intensity. Repetitive elements from the following. X-ray source, Spectrometer stability detector and the electronic power supply unit; peak intensity measurement of the sample position sensitivity and statistical noise spectrum at the peak. In this method, it should be limited to the working conditions in order to ensure the strength was measured noise is relatively small. This is discussed in Appendix A. weight The value of the complex will depend on the standard deviation of the sample positioning method. In 4.7.1, we need to use the same method of locating the sample, only the final calibration The method of using the targeted sample to be effective. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 28633-2012_English be delivered?Answer: Upon your order, we will start to translate GB/T 28633-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 28633-2012_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 28633-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
