GB/T 28277-2012 English PDF

US$459.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 28277-2012: Silicon-based MEMS fabrication technology -- Measurement method of cutting and pull-press strength of micro bonding area
Status: Valid

Standard ID	USD	BUY PDF	Lead-Days	Standard Title (Description)	Status
GB/T 28277-2012	459	Add to Cart	4 days	Silicon-based MEMS fabrication technology -- Measurement method of cutting and pull-press strength of micro bonding area	Valid

Similar standards

GB/T 43770   GB/T 43978   SAMR 76   GB/T 28275   GB/T 28276   GB/T 28274   

Basic data

Standard ID: GB/T 28277-2012 (GB/T28277-2012)
Description (Translated English): Silicon-based MEMS fabrication technology -- Measurement method of cutting and pull-press strength of micro bonding area
Sector / Industry: National Standard (Recommended)
Classification of Chinese Standard: L55
Classification of International Standard: 31.200
Word Count Estimation: 20,272
Quoted Standard: GB/T 26111-2010; GB/T 19022-2003
Regulation (derived from): National Standards Bulletin No. 9 of 2012
Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Summary: This standard specifies the silicon MEMS processing involved in the bonding region tiny bond strength testing requirements and test methods. This standard applies to the use of micro technology and related microfabrication technology to produce the tiny a

GB/T 28277-2012: Silicon-based MEMS fabrication technology -- Measurement method of cutting and pull-press strength of micro bonding area

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
ICS31.200 L55 National Standards of People's Republic of China Silicon MEMS Manufacturing Technology Micro-bonding strength in tension and compression and shear zone detection method Issued on. 2012-05-11 2012-12-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released

Table of Contents

Introduction Ⅲ 1 Scope 1 2 Normative references 1 3 Terms and definitions 4 requires 2 4.1 Detection structural design requirements 2 4.2 Preparation of samples structural requirements 4 4.3 detect environmental requirements 4 5 5 Detection 5.1 General 5 5.2 micro structural tension and compression bonding strength detection 5 5.3 micro structural shear bond strength detector 6 Appendix A (informative) detector design tension and compression fracture strength and size correspondence table 8 Annex B (informative) tension and compression detector test case structure 16

Foreword

This standard rule according to GB/T 1.1-2009 given draft. This standard by the National MEMS Technology Standardization Technical Committee (SAC/TC336) and focal points. This standard was drafted. Peking University, the machine on Productivity Center, China Electronics Technology Group Corporation 13th Research Institute, Chinese Academy of Sciences Sea Institute of Microsystem and Information Technology, China Electronics Technology Group Institute of the forty-ninth. The main drafters of this standard. DAR ES SALAAM, Wang Wei, Liu Wei, Yang Fang, Jiang forests, Cui Bo, Xiong Bin, Tian Lei. Silicon MEMS Manufacturing Technology Micro-bonding strength in tension and compression and shear zone detection method

1 Scope

This standard specifies the requirements and test methods for silicon-based MEMS process involved small bonding area bonding strength detection. This standard applies to the use of small shear bond area of \u200b\u200bmicroelectronics technology and related manufacturing and microfabrication technology tension and compression strength test.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated edition applies to this article Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 26111-2010 micro-electromechanical systems (MEMS) technology terms and definitions GB/T 19022-2003 Measurement management systems for measurement processes and measuring equipment

3 Terms and Definitions

GB/T 26111-2010 and GB/T 19022-2003 defined and the following terms and definitions apply to this document. 3.1 Bulk micro-machined bulkmicromachining Achieve micromachined micro structure by selectively removing a portion of the base material. NOTE. bulk micromachining process by chemically etching the substrate to remove the unnecessary portion of the processing method using SiO2 or Si3N4 mask to protect the table. Surface is not etched. Boron-doped layer can also stop the etching of the surface layer in the following sections. [GB/T 26111-2010, the definition 3.5.16] 3.2 Dry etching dryetching Use may produce a physical and/or chemical reaction of the gas or plasma etching techniques. Note. the reaction gas may react with the substrate and the electronic energy generated removing material to form the desired shape or size can be divided into dry etching utilizing a chemical reaction. It should isotropic etching (plasma etching) and the use of direct physical etching reaction (ion etching). [GB/T 26111-2010, the definition 3.5.18] 3.3 Wet etching wetetching Utilization of material to be engraved can produce a chemical reaction solution or a thin film device structure etching technology. Note. during wet etching, etching of part of the mask will not need to expose the rest, and then the material is immersed in the reaction solution can be divided to each. Isotropic etching and anisotropic etching. [GB/T 26111-2010, the definition 3.5.17] 3.4 Isotropic etching isotropicetching Etching speed does not vary with the crystal to change direction or energy beam etching process. [GB/T 26111-2010, the definition 3.5.19] ......

Image     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of GB/T 28277-2012_English be delivered?

Answer: Upon your order, we will start to translate GB/T 28277-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of GB/T 28277-2012_English with my colleagues?

Answer: Yes. The purchased PDF of GB/T 28277-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.