GB/T 21021.1-2021 English PDFUS$234.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 21021.1-2021: Intermodulation level measurement for passive RF and microwave devices - Part 1: General requirements and measuring methods Status: Valid GB/T 21021.1: Historical versions
Basic dataStandard ID: GB/T 21021.1-2021 (GB/T21021.1-2021)Description (Translated English): Intermodulation level measurement for passive RF and microwave devices - Part 1: General requirements and measuring methods Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L26 Word Count Estimation: 13,183 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 21021.1-2021: Intermodulation level measurement for passive RF and microwave devices - Part 1: General requirements and measuring methods---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Intermodulation level measurement for passive RF and microwave devices - Part 1.General requirements and measuring methods ICS 33.120.10 L26 National Standards of People's Republic of China Replace GB/T 21021-2007 Intermodulation level measurement of passive radio frequency and microwave components Part 1.General requirements and measurement methods (IEC 62037-1.2012,PassiveRFandmicrowavedevices,intermodulationlevel Released on 2021-11-26 2022-06-01 implementation State Administration for Market Regulation Issued by the National Standardization Management Committee ForewordGB/T 21021 "Intermodulation level measurement of passive radio frequency and microwave components" has released the following parts. ---Part 1.General requirements and measurement methods; ---Part 2.Passive intermodulation measurement of coaxial cable assemblies; ---Part 3.Passive intermodulation measurement of coaxial connectors; ---Part 4.Passive intermodulation measurement of coaxial cable. This part is Part 1 of GB/T 21021. This section was drafted in accordance with the rules given in GB/T 1.1-2009. This part replaces GB/T 21021-2007 "Radio frequency connector, connector cable assembly and cable intermodulation level measurement". and Compared with GB/T 21021-2007, the main technical changes except for editorial changes are as follows. ---Modified the measuring range of the device (see Chapter 6, Chapter 4 of the.2007 edition); ---Added guidelines for minimizing passive intermodulation generation (see Chapter 7); ---Added optional steps for additional mechanical shock tests during the test (see Chapter 8); --- Modified the display of measurement results (see Chapter 9, Chapter 7 of the.2007 edition); ---Added the composition of low PIM load, the precautions of the test procedure (see Appendix A, Appendix B). The translation method used in this part is equivalent to IEC 62037-1.2012 "Intermodulation Level Measurement of Passive Radio Frequency and Microwave Components Part 1 Points. General requirements and measurement methods. Please note that some of the contents of this document may involve patents. The issuing agency of this document is not responsible for identifying these patents. This part was proposed by the Ministry of Industry and Information Technology of the People's Republic of China. This part is under the jurisdiction of the National Standardization Technical Committee for High-frequency Cables and Connectors for Electronic Equipment (SAC/TC190). Drafting unit of this section. The 23rd Research Institute of China Electronics Technology Group Corporation. The main drafters of this section. Yin Haicheng, Fang Xu, Tian Xin. The previous releases of the standards replaced by this part are as follows. ---GB/T 21021-2007. Intermodulation level measurement of passive radio frequency and microwave components Part 1.General requirements and measurement methods1 ScopeThis part of GB/T 21021 describes the passive interaction generated by two or more transmission signals in passive radio frequency and microwave components. General requirements and measurement methods for level adjustment. The test procedures in this section specify the general requirements and measurement of undesired intermodulation signals generated when transmitting two signals method. Each part of GB/T 21021 describes the measurement method of passive intermodulation (PIM), but does not involve the long-term performance of products related to this performance. Reliability. This part is used in conjunction with other parts of GB/T 21021.2 Normative referencesThere are no normative references in this section.3 AbbreviationsThe following abbreviations apply to this document. CATV. Cable Television (communityantennatelevision) DUT. device under test (deviceundertest) IM. Intermodulation (intermodulation) PIM. Passive Intermodulation (passive intermodulation)4 Characteristics of intermodulation productsPIM interference is caused by a variety of unknown characteristics, locations and states of nonlinear sources, such as metal-to-metal contact, material selection, and corrosion Products, stains, etc. Due to mechanical stress, temperature changes, material properties changes (such as cold flow, etc.), and climate changes, most of these effects follow Time changes. Intermodulation products are generated from various point sources inside the DUT and propagate in all directions that can be propagated. The production of PIM products may not follow the usual quadratic nonlinear equations. Therefore, it is impossible to accurately calculate the resulting intermodulation Other power levels. The comparison of PIM should be performed at the same power level. In addition, the generation of PIM may be related to frequency. When the generation of PIM depends on frequency, the performance of PIM should be improved in a specific frequency band. Line research.5 Principle of the test procedureCombine the two signals f1 and f2 with equal power levels and input them into the DUT, and test the harmonic signal or self-intermodulation signal contained in the signal The signal level should be at least 10dB lower than the expected intermodulation level in the DUT. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 21021.1-2021_English be delivered?Answer: Upon your order, we will start to translate GB/T 21021.1-2021_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 21021.1-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 21021.1-2021_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 21021.1-2021?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 21021.1-2021 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
