GB/T 17505-2016 PDF EnglishUS$135.00 · In stock · Download in 9 seconds
GB/T 17505-2016: Steel and steel products -- General technical delivery requirements Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 17505: Historical versions
Similar standardsGB/T 17505-2016: Steel and steel products -- General technical delivery requirements---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT17505-2016GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.140.01 H 40 Replacing GB/T 17505-1998 Steel and steel products – General technical delivery requirements (ISO 404.2013, MOD) Issued on. FEBRUARY 24, 2016 Implemented on. JANUARY 1, 2017 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration Committee. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Terms and definitions... 6 4 Ordering information provided by user... 9 5 Manufacturing process... 10 6 Supply by intermediary... 10 7 Requirements... 11 8 Inspection and testing... 13 9 Reclassification and repair... 19 10 Marks... 19 11 Objection... 20 Annex A... 22 Bibliography... 24ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard replaces GB/T 17505-1998 Steel and Steel Products - General Technical Delivery Requirements. Compared with GB/T 17505-1998, the main technical changes are as follows. - changed the name of standard to “Steel and steel products - General technical delivery requirements”; - moved “This Standard must be used together with other technical standards; it cannot be used for ordering” from “Foreword” to “Scope” (see NOTE in Clause 1 of this edition; Foreword of 1998 edition); - deleted terms and definition, relevant requirements of continuous inspection (see 3.3, 8.1.2 of 1998 edition); - added terms and definitions for “manufacturer” and “intermediary”; defined the respective rights and obligations (see 3.14, 3.15, 6.4 of this edition); - modified the definition of “inspection representative” as well as its relevant rights and obligations (see 3.6, 8.3.1.3 of this edition; 3.5, 8.3.1.3 of 1998 edition); - modified the definition of “cast analysis”; added relevant instructions and general provisions on methods for chemical analysis (see 3.11, 7.2 of this edition; 3.12, 7.2 of 1998 edition); - modified the name of Clause 4 from “Ordering content” to “Ordering information provided by user” (see Clause 4 of this edition); - modified requirements for “intermediary” (see Clause 6 of this edition); - specified requirements for “inspection documents” and “quality certificate” (see 6.1, Clause 8 of this edition); - supplemented with relevant surface quality inspection standards (see NOTE in 7.4.1.2 of this edition; 7.4.1 of 1998 edition); - added requirements for “welding repair” (see 7.4.4.1 of this edition; 7.4.4 of 1998 edition); - added requirements for protection of “safety and health” (see 7.1 of this edition; 7.1 of 1998 edition); - modified “ordering content” (see 8.3.1.1 of this edition; 8.3.1.1 of 1998 edition); - modified “the composition of test unit” (see 8.3.2.1 of this edition; 8.3.2.1 of 1998 edition); - added preparation requirements for sample (see 8.3.3.1 of this edition; 8.3.3.1 of 1998 edition); - modified “rounding of test results” (see 8.5 of this edition; 8.5 of 1998 edition); - added “Technical differences and reasons between this Standard and ISO 404.2013” (see Annex A of this edition); - added “common standards for other test methods of steel products” (see 8.3.4.1.4 and Bibliography of this edition). This Part uses redrafting method to modify and adopt ISO 404.2013 Steel and steel products - General technical delivery requirements. This Standard is basically consistent with ISO 404.2013.However, when using ISO 404.2013, in content, it made modification by combining China’s national conditions. Relevant technical differences have been incorporated into the body and marked on the margin of the involved provisions. The technical differences and reasons are given in Annex A for reference. This Standard was proposed by China Iron and Steel Association. This Standard shall be under the jurisdiction of National Technical Committee on Steel of Standardization Administration of China (SAC/TC 183). The drafting organization of this Standard. China Metallurgical Information & Standardization Institute. Main drafters of this Standard. Luan Yan, Dai Qiang, Yan Chengming. The previous version replaced by this Standard is as follows. - GB/T 17505-1998. Steel and steel products – General technical delivery requirements1 ScopeThis Standard specifies general technical delivery requirements for steel and steel products contained in GB/T 15574 (excluding steel and powder metallurgy products).2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 1467 Method for chemical analysis of metallurgy product - General rules and regulations3 Terms and definitionsFor the purposes of this document, the terms and definitions given in GB/T 13304.1, GB/T 13304.2 and GB/T 15574 and the following terms and definitions apply. before delivery, according to the technical requirements of contract, conduct the inspection and testing for delivered products or partial products so as to verify if they meet the contract’s requirements4 Ordering information provided by userThe contract shall include all content required to describe the product characteristics and the following details about delivery.5 Manufacturing processUnless there is an agreement at the time of order or as otherwise specified in the product standard, the manufacturing process shall be selected by the manufacturer.6 Supply by intermediaryIf the intermediary changes the product size, it shall provide an additional document which is in line with the new state. It is also applicable to all special requirements not contained in manufacturer’s inspection document or quality certificate.7 RequirementsUnless otherwise specified that it is product analysis, the requirements related to chemical composition all refer to cast analysis. The analysis method shall comply with the provisions of GB/T 1467. When required, the special technology for defect detection (such as X-ray detection, ultrasonic inspection, magnetic particle testing, etc.) as well as its number of product testing unit, processing method of test results shall be in accordance with product standard or determined via negotiation during ordering.8 Inspection and testingDuring testing, manufacturer shall ensure the traceability between sample product, sample, test piece and test unit. Sequential testing results shall be assessed by the following methods (take impact testing results as an example).9 Reclassification and repairManufacture has right to conduct reclassification or repair to unqualified product before or after re-inspection (for example. heat treatment, cutting, rolling, drawing, etc.), then according to 8.3.2, submit those products for acceptance as new test units.10 MarksManufacture shall make marks according to product standard or contract requirements for product or delivery batch.11 ObjectionIn case of any dispute, the sample conditions and testing methods used to determine the controversial characteristic values shall be performed according to the provisions of corresponding national standards or industrial standard, or the provisions of 8.3.3 and 8.3.4. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 17505-2016 be delivered?Answer: The full copy PDF of English version of GB/T 17505-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 17505-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 17505-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 17505-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 17505-2016?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 17505-2016 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 17505-2016?A step-by-step guide to download PDF of GB/T 17505-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 17505-2016". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
