GB/T 16608.1-2023 English PDFUS$1014.00 · In stock
Delivery: <= 6 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 16608.1-2023: Electromechanical telecom elementary relays of assessed quality - Part 1: Generic specification and blank detail specification Status: Valid GB/T 16608.1: Historical versions
Basic dataStandard ID: GB/T 16608.1-2023 (GB/T16608.1-2023)Description (Translated English): Electromechanical telecom elementary relays of assessed quality - Part 1: Generic specification and blank detail specification Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L25 Classification of International Standard: 29.120.70 Word Count Estimation: 56,597 Date of Issue: 2023-03-17 Date of Implementation: 2023-10-01 Older Standard (superseded by this standard): GB/T 16608.1-2003,GB/T 16608.50-2012,GB/T 16608.51-2012,GB/T 16608.52-2012,GB/T 16608.53-2012,GB/T 16608.54-2012,GB/T 16608.55-2012 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 16608.1-2023: Electromechanical telecom elementary relays of assessed quality - Part 1: Generic specification and blank detail specification---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. ICS29:120:70 CCSL25 National Standards of People's Republic of China GB/T 16608:1-2023/IEC 61811-1:2015 Replacing GB/T 16608:1-2003, GB/T 16608:50~16608:55-2012 Basic electromechanical relays for telecommunications with qualification Part 1: General specification and blank detail specification (IEC 61811-1:2015, IDT) Released on 2023-03-17 2023-10-01 implementation State Administration for Market Regulation Released by the National Standardization Management Committee table of contentsPreface V Introduction VII 1 Scope 1 2 Normative references 1 3 Terms and Definitions 2 3:1 Relay Type 2 3:2 Contact category 2 3:3 Contact failure and contact failure3 3:4 Relay failure and relay failure 3 3:5 Relay structure category 3 3:6 Test level and sample size 4 4 rating 4 4:1 General 4 4:2 Coil rated voltage 4 4:3 Contact circuit resistance4 4:4 Dielectric withstand voltage test 4 4:5 Impulse voltage test 4 4:6 Insulation resistance 5 4:7 Number of cycles to determine electrical durability5 4:8 Contact failure rate for test evaluation5 5 Signs and Documents 5 5:1 General 5 5:2 Relay mark 5 5:3 Packaging mark 5 5:4 Manufacture date code 5 6 Blank detail specification and formulation of detail specification 5 7 Quality assessment procedure 6 7:1 Initial manufacturing stage 6 7:2 Structure-similar relays 7 7:3 Appraisal and approval procedure 7 7:4 Quality Consistency Inspection 7 7:5 Inspection cycle (period between each inspection) 9 8 Inspection Form 9 8:1 Test sequence 9 8:2 Relay category, based on environmental protection (RT: relay manufacturing process) 9 8:3 Contact application category 9 8:4 Test sequence 9 8:5 Inspection groups and inspection groups 10 9 trials 14 9:1 Standard conditions for testing 14 9:2 Installation of test samples during the test 14 9:3 General conditions for testing 14 10 Ordering Information 14 Appendix A (Informative) Relay Reliability---Failure Rate Data 15 A:1 General 15 A:2 Range15 A:3 Relay description 15 A:4 Failure and failure rate data 15 A:5 Data sources16 A:6 Weibull method16 A:7 Weibull Bayesian method 16 Appendix B (Normative) Relay Characteristics 19 B:1 General parameters 19 B:2 Coil parameters 19 B:3 Contact parameters 20 B:4 Installation 21 B:5 Environmental parameters 21 B:6 Packaging of automatic operation relays (when applicable) 21 Appendix C (Normative) Blank detail specification and detail specification 22 C:1 Home page example 22 C:2 Accreditation approval process 28 C:3 Quality Consistency Inspection 29 C:4 Composition of inspection lot 29 Appendix D (Informative) Grouping Definitions 46 Reference 47 Figure A:1 Comparison of Weibull Bayesian lines for new and old relay designs18 Table 1 Group A 10 Table 2 Group B 11 Table 3 Group C 12 Table B:1 dielectric withstand voltage test voltage 19 Table B:2 Impulse test voltage 19 Table B:3 Coil parameters 20 Table B:4 Electrical durability test and overload test load, contact circuit resistance limit value, number of cycles and cycle rate 20 Table C:1 Quality Consistency Inspection 29 Table C:2 Qualification Approval Inspection 43 Table C:3 Industrial application qualification 45forewordThis document is in accordance with the provisions of GB/T 1:1-2020 "Guidelines for Standardization Work Part 1: Structure and Drafting Rules for Standardization Documents" drafting: This document is Part 1 of GB/T 16608 "Basic Electromechanical Relays for Telecommunications with Quality Assessment": GB/T 16608 has issued Published the following sections: --- Part 1: General specification and blank detail specification: This document replaces GB/T 16608:1-2003 "Electromechanical relays with or without foundation with quality assessment - Part 1: General specification", GB/T 16608:50-2012 "with or without electrical relays - Part 50: sub-standard for telecommunications with or without quality assessment of electrical relays Electrical appliances", GB/T 16608:51-2012 "With or without electrical relays Part 51: Blank detailed specification for telecommunications with quality assessment Non-standard types and structures of electromechanical relays with or without electromechanical relays", GB/T 16608:52-2012 " electromechanical relays with or without electromechanical relays - Part 52: Empty White detailed specification for quality-assessed electrical relays with or without two sets of changeover contacts for telecommunications, 20mm×10mm base", GB/T 16608:53-2012 "With or without electrical relays - Part 53: Blank detailed specification for telecommunications with or without quality assessment Two sets of changeover contacts for electromechanical relays, 14mm×9mm base", GB/T 16608:54-2012 "With or without electromechanical relays No: 54 Part: Blank detailed specification for quality-assessed electrical relays with or without two sets of changeover contacts for telecommunications, 15mm x 7:5mm base "Relay", GB/T 16608:55-2012 "With or without electrical relay - Part 55: Blank detailed specification for telecommunications with quality assessment Or two sets of changeover contacts for inorganic electrical relays, 11 mm × 7:5 mm (maximum) base", and GB/T 16608:1-2003, Compared with GB/T 16608:50~16608:55-2012, except for structural adjustment and editorial changes, the main technical changes are as follows: --- Changed the scope of application (see Chapter 1, Chapter 1 of GB/T 16608:1-2003): This document identically adopts IEC 61811-1:2015 "Basic electromechanical relays for telecommunications with quality assessment - Part 1: General specification and space White Detailed Specification": The following editorial changes have been made to this document: --- Changed the list of normative references in Chapter 2; --- 4:8 added note; ---Corrected the unnumbered error of the formula in A:7:4 of IEC 61811-1:2015, and increased the formula number (A:2); ---Corrected the name error in Figure A:1 in IEC 61811-1:2015, by "Weibull Bayesian of new compressor design and old design Line Contrast" was corrected to "Weibull Bayes Line Contrast of New vs: Old Relay Design"; --- Corrected the nature of Appendix B and Appendix C according to the reference in the text; ---Corrected the error in B:1 in IEC 61811-1:2015, from "dielectric withstand voltage: see Table B:2" to "impulse test voltage: see Table B:2"; ---Corrected the error in the test number A0-1 "coil resistance" of Table C:1 of IEC 61811-1:2015, by "value according to Table B:2 "Regulations" is corrected to "the values are in accordance with the provisions of Table B:3"; ---Corrected the error in the test number 11 "Solderability (D)" of Table C:1 of IEC 61811-1:2015, changed from "value according to the specifications in Table B:5 "Setting" is corrected to "the value is in accordance with the provisions of Table B:1"; ---Corrected the error in Table C:1 Test No: 12 "Electrical Durability, Cable Load (D)" of IEC 61811-1:2015: The provisions of B:4 in GB/T 21711:7-2018" were corrected to "according to the provisions of C:4 in GB/T 21711:7-2018"; ---Corrected the error in the test number 38 "Soldering heat resistance (D)" of Table C:1 of IEC 61811-1:2015, from "Through-hole type: 4:25:3, Test 2" was corrected to "through-hole type: 4:25:2, Test 2"; --- Corrected errors in Table C:2 and Table C:3 of IEC 61811-1:2015 in the test item "Electrical Durability", GB/T 21711:7- There is no "method 1" in 4:30 of:2018, and it is changed from "method 1" to "method 1 (severity level A)": Please note that some contents of this document may refer to patents: The issuing agency of this document assumes no responsibility for identifying patents: This document is proposed by the Ministry of Industry and Information Technology of the People's Republic of China: This document is under the jurisdiction of the National Standardization Technical Committee (SAC/TC217) with or without electrical relays: This document is drafted by: Xiamen Hongfa Acoustics Co:, Ltd:, Sichuan Hongfa Acoustics Co:, Ltd:, China Electronic Technology Standardization Research Institute Academy: The main drafters of this document: Li Huiping, Lin Weilin, Zhang Desheng, Wang Jue: This document was first published as GB/T 16608-1996 in:1996; when it was revised for the first time in:2003, it was published in parts: According to GB/T 16608:1-2003 "Basic or non-basic electromechanical relays with quality assessment - Part 1: General specification"; this is the second revision This revision incorporates the contents of GB/T 16608:50~16608:55-2012:IntroductionIn order to standardize the quality evaluation of basic electromechanical relays for telecommunications in my country, guide the formulation of product standards for enterprises, and promote product development and production GB/T 16608 aims to establish general specifications and blank detailed specifications applicable to basic electromechanical relays for telecommunications, and to provide industrial and other equipment with relays for reference: GB/T 16608 is proposed to be divided into the following parts: --- Part 1: General specification and blank detail specification: The purpose is to establish suitable for telecommunications equipment, industrial equipment and other equipment relay General specification for electrical appliances and for use in detailed specifications developed in accordance with this document: --- Part 2: sub-standard: The purpose is to establish sectional specifications applicable to basic electromechanical relays for specific applications: Basic electromechanical relays for telecommunications with qualification Part 1: General specification and blank detail specification1 ScopeThis document applies to basic electromechanical relays for telecommunications: Relays conforming to this document are suitable for use in telecommunication equipment, but as a basic Basic electromechanical relays are also suitable for use in specific industrial and other equipment: This document selects the appropriate test methods from IEC 61810 (all parts) and other documents for the detailed specification developed in accordance with this document use: Basic inspection tables are also specified in this document, applicable to detail specifications developed in accordance with this document: Detailed inspection tables are specified in the detail specification:2 Normative referencesThe contents of the following documents constitute the essential provisions of this document through normative references in the text: Among them, dated references For documents, only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to this document: GB/T 2423:23-2013 Environmental testing Part 2: Test method Test Q: Sealing (IEC 60068-2-17:1994, IDT) GB/T 2691-2016 Marking codes for resistors and capacitors (IEC 60062:2004, IDT) GB/T 21711:7-2018 Basic electromechanical relays Part 7: Test and measurement procedures (IEC 61810-7:2006, IDT) Note: GB/T 2828 (all parts) counting sampling inspection procedures [ISO 2859 (all parts)] and guidance) Note: GB/T 2423:1-2008 Environmental testing for electric and electronic products Part 2: Test method Test A: Low temperature (IEC 60068-2-1:2007, IDT) IEC 60068-2-20:2008 Environmental testing Part 2-20: Test method Test T: Solderability and reliability of terminal components Note: GB/T 2423:28-2005 Environmental testing for electric and electronic products Part 2: Test method Test T: Soldering (IEC 60068-2-20:1979, IDT) IEC 60068-2-58:2004 Environmental testing No: 2-58: Test method Test Td: Solderability of surface mount components (SMD) utes) IEC 60695-11-5:2004 Fire Hazard Tests for Electrical and Electronic Products Test Methods for Flame Needle Flame Test Devices and Confirmation Tests Methods and guidelines (Firehazardtesting-Testflames-Needle-flametestmethod-Apparatus, confirmatory Note: GB/T 5169:5-2020 Fire Hazard Tests for Electrical and Electronic Products Part 5: Test Flame Needle Flame Test Method Device, Confirmation Test Method ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 16608.1-2023_English be delivered?Answer: Upon your order, we will start to translate GB/T 16608.1-2023_English as soon as possible, and keep you informed of the progress. The lead time is typically 4 ~ 6 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 16608.1-2023_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 16608.1-2023_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 16608.1-2023?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 16608.1-2023 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
