GB/T 1633-2000 PDF EnglishUS$65.00 · In stock · Download in 9 seconds
GB/T 1633-2000: Plastics - Thermoplastic materials - Determination of vicat softening temperature (VST) Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure GB/T 1633: Historical versions
Similar standardsGB/T 1633-2000: Plastics - Thermoplastic materials - Determination of vicat softening temperature (VST)---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT1633-2000 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.080.20 G 31 idt ISO 306:1994 Replacing GB/T 1633-1979 (1989) Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) ISSUED ON: JULY 31, 2000 IMPLEMENTED ON: MARCH 01, 2001 Issued by: State Bureau of Quality Technical Supervision Table of ContentsForeword ... 3 ISO Foreword ... 5 1 Scope ... 6 2 Normative references ... 6 3 Principle ... 7 4 Instruments ... 7 5 Specimens ... 9 6 State conditioning ... 10 7 Operating steps ... 10 8 Test report ... 11 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)1 ScopeThis standard specifies four test methods for determining the Vicat softening temperature (VST) of thermoplastics. A50 method -- Using a force of 10 N, the heating rate is 50 °C/h B50 method -- Using a force of 50 N, the heating rate is 50 °C/h A120 method -- Using a force of 10 N, the heating rate is 120 °C/h B120 method -- Using a force of 50 N, the heating rate is 120 °C/h The four methods specified in this standard are only applicable to thermoplastics. The temperature measured is the temperature at which thermoplastics begin to soften rapidly.2 Normative referencesThe provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard shall explore the possibility of using the latest version of the following standards. GB/T 2918-1998 Plastics - Standard atmospheres for conditioning and testing (idt ISO 291:1997) GB/T 9352-1988 Plastic - Compression moulding of test specimens of thermoplastic materials (neq ISO 293:1986) GB/T 11997-1989 Plastic - Multipurpose test specimens (eqv ISO 3167:1983) GB/T 17037.1-1997 Injection moulding of test specimens of thermoplastic materials - Part 1: General principles and moulding of multipurpose and bar test specimens (idt ISO 294-1: 1996) ISO 2818:1994 Plastics - Preparation of test specimens by machining nickel-iron alloy or borosilicate glass), blank tests are performed for each instrument including the temperature range in which it is used. A correction term is determined for each temperature. If the correction term is 0.02 mm or greater, it shall note its algebraic sign, which is added to the apparent penetration by algebraic methods. This correction term is applied to each test. It is recommended to use instruments made of low expansion alloys. 4.2 The indenter, preferably a cylinder made of hardened steel with a length of 3 mm and a cross-sectional area of 1.000 mm2 ± 0.015 mm2. Fixed to the bottom of the load rod, the lower surface of the indenter shall be flat, perpendicular to the axis of the load rod, free of burrs. 4.3 A calibrated micrometer (or other suitable measuring instrument) capable of measuring the penetration of the indenter into the specimen by 1 mm ± 0.01 mm and recording the thrust of the micrometer as part of the thrust of the specimen. Note: 1. In this type of instrument, the micrometer spring force is upward and shall be subtracted from the load; if this force is downward, it shall be added to the load. 2. During the entire stroke, since the force applied to the micrometer spring changes significantly, this force shall be measured throughout the stroke. 4.4 Load plate is mounted on the load rod, which has a suitable weight in the center, so that the total thrust applied to the specimen reaches 10 N ± 0.2 N for A50 and A120, or 50 N ± 1 N for B50 and B120. The downward thrust of the load rod, indenter, load plate micrometer spring combination shall not exceed 1 N. 4.5 Heating equipment uses a heating bath, which is filled with liquid, OR a forced blast nitrogen circulation oven. The heating equipment shall be equipped with a controller, that can heat up at a uniform rate of 50 °C/h ± 5 °C/h or 120 °C/h ± 10 °C/h as required. During the test, if the temperature change every 6 minutes is 5 °C ± 0.5 °C or 12 °C ± 1 °C, respectively, the heating rate shall be considered to meet the requirements. Adjust the instrument so that when the specified indentation is reached, the heater is automatically cut off and an alarm sounds. 4.5.1 Heating bath contains the liquid in which the specimen is immersed and is equipped with an efficient stirrer; the specimen is immersed to a depth of at least 35 mm. Make sure that the selected liquid is stable at the use temperature and has no effect on the test material, such as expansion or cracking. When a heating bath is used, the temperature of the liquid near the specimen is measured as the Vicat softening temperature (VST) (see 7.5). Liquid paraffin, transformer oil, glycerine, silicone oil are all suitable heat transfer 5.3 For sheet materials, the specimen thickness shall be equal to the original sheet thickness, except as follows: a) If the specimen thickness exceeds 6.5 mm, it shall be reduced to 3 ~ 6.5 mm by mechanical processing on one side in accordance with ISO 2818, leaving the other surface intact. The test surface shall be the original surface. b) If the sheet thickness is less than 3 mm, up to three specimens shall be directly superimposed together, so that the total thickness is between 3 ~ 6.5 mm, with the thickness of the upper sheet being at least 1.5 mm. Superimposing sheets of smaller thickness may not necessarily give the same test results. 5.4 The test results obtained may be related to the molding conditions used to prepare the specimens, although such dependence is uncommon. When the test results depend on the molding conditions, special annealing or pretreatment steps may be used before testing after agreement between the parties concerned.6 State conditioningUnless there are provisions or requirements for the materials under test, the specimen shall be conditioned according to GB/T 2918.7 Operating steps7.1 Place the specimen horizontally under the unloaded indenter. The indenter shall be no less than 3 mm from the edge of the specimen; the specimen surface in contact with the instrument base shall be flat. 7.2 Place the assembly in the heating device and start the agitator. At the beginning of each test, the temperature of the heating device shall be 20 ~ 23 °C. When using a heating bath, the mercury ball of the thermometer or the sensing part of the temperature measuring instrument shall be at the same level as the specimen and as close to the specimen as possible. If the preliminary test shows that starting the test at other temperatures will not cause errors for the test material, other starting temperatures can be used. 7.3 After 5 min, with the indenter in a stationary position, add sufficient weight to the load plate, so that the total thrust on the specimen is 10 N ± 0.2 N for A50 and A120 and 50 N ± 1 N for B50 and B120. Then, take the reading of the dial gauge (or other indentation measuring instrument) or zero the instrument. 7.4 Raise the temperature of the heating device at a rate of 50 °C/h ± 5 °C/h or 120 °C/h ± 10 °C/h; when using a heating bath, stir the liquid thoroughly during the test; for arbitration tests, use a heating rate of 50 °C/h. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 1633-2000 be delivered?Answer: The full copy PDF of English version of GB/T 1633-2000 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 1633-2000_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1633-2000_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 1633-2000 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 1633-2000?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 1633-2000 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 1633-2000?A step-by-step guide to download PDF of GB/T 1633-2000_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 1633-2000". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
