GB/T 14442-2008 English PDFUS$229.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 14442-2008: Safety and health regulation for fur manufacture Status: Valid GB/T 14442: Historical versions
Basic dataStandard ID: GB/T 14442-2008 (GB/T14442-2008)Description (Translated English): Safety and health regulation for fur manufacture Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: C70 Classification of International Standard: 13.100 Word Count Estimation: 10,143 Date of Issue: 2008-12-15 Date of Implementation: 2009-10-01 Older Standard (superseded by this standard): GB/T 14442-1993 Regulation (derived from): Announcement of Newly Approved National Standards No. 21 of 2008 (No. 134 overall) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the fur production industry safety and health requirements and technical measures. This standard applies to the raw percutaneous preparation, tanning, dyeing and processing into the dual- skin leather fur or wool fur production enterprises, workshops and workplaces. GB/T 14442-2008: Safety and health regulation for fur manufacture---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Safety and health regulation for fur manufacture ICS 13.100 C70 National Standards of People's Republic of China Replacing GB/T 14442-1993 Fur production safety and health regulations Posted 2008-12-15 2009-10-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThis standard replaces GB/T 14442-1993 "fur production safety and health regulations." This standard and GB/T 14442-1993 compared to the main changes are as follows. --- Update the normative references; --- Increasing the plant and some provisions of occupational health in the workplace; --- Deletion of some provisions, adjusted some text. This standard was proposed by the State Administration of Work Safety. This standard by the National Safe Production Standardization Technical Committee (SAC/TC288) centralized. This standard was drafted. Capital University of Economics and Trade, China Leather Association. The main drafters of this standard. Wang Yongyi, Guo Wenhong, Guo Jianzhong, Jiang Kang, Lin Xiushan. This standard June 10, 1993 was first released in 2008, the first revision. Fur production safety and health regulations1 ScopeThis standard specifies the requirements and technical measures for fur production industry safety and health. This standard applies to raw materials percutaneous preparation, tanning, dyeing and processing into fur or wool leather dual-skin fur production enterprises, workshops and for Industry sites.2 Normative referencesThe following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. GB 2893 Safety colors GB 2894 Safety Signs and use guidelines GB 5083 production equipment with safety and health General GB 15603 commonly used hazardous chemicals stored General GB 18218 identification of major hazard GB 50016 architectural design code for fire protection GB 50052 power supply and distribution system design specifications GB 50054 low voltage power distribution design specifications GB 50058 Explosion and fire hazard electrical installation design specifications3 factories and workplaces3.1 Plant structure should be strong, building materials should have a strong resistance to corrosion and moisture performance; wet work plant should be preferred storey building. 3.2 plant should have good lighting, heating facilities; high temperature, high humidity and noxious fumes of the plant should be appropriate heightening, leave enough window area. 3.3 wet job shop floor should comply with corrosion resistance and thermal conductivity small request. According to the amount of water and other liquids, the ground should be designed and built Corresponding drainage facilities, drainage slope and leave enough to make non-slip handle. 3.4 proper storage of semi-finished fur workshop and retain appropriate width of safe passage. 3.5 raw hides warehouses and workplaces should be built in the dry, not flooded area; the scope of land should be chosen to meet the health and epidemic prevention The relevant provisions; ground should drain and sewage discharge facilities; roof and walls should be smooth, seamless. 3.6 fire protection shall comply with the provisions of GB 50016. 3.7 installation of electrical equipment, use should be consistent with GB 50052, GB 50054 and GB 50058 of the relevant provisions. 3.8 Total industrial enterprises disposed plane, under the premise of the project to meet the needs of the body, and the workplace should be provided separately from non-work areas; pollution Dyeing facilities away from serious harm non-polluting facilities; produce dust workshop and produce poison workshops separately; generating occupational hazards and workshop CHP has some other green belt between the workshop and living area. 3.9 workplace should not be used as a circulating hot air heating and air conditioning. Machinery and equipment 4 4.1 safety guards and safety technical measures 4.1.1 the relevant provisions of the production equipment used should be consistent with GB 5083 might harm people on rotating machinery parts, such as ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 14442-2008_English be delivered?Answer: Upon your order, we will start to translate GB/T 14442-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 14442-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 14442-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 14442-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 14442-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
