GB/T 1040.3-2006 PDF EnglishUS$70.00 · In stock · Download in 9 seconds
GB/T 1040.3-2006: Plastics -- Determination of tensile properties -- Part 3: Test conditions for films and sheets Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 1040.3-2006: Plastics -- Determination of tensile properties -- Part 3: Test conditions for films and sheets---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT1040.3-2006 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.080.01 G 31 GB/T 1040.3-2006 / ISO 527-3.1995 Replacing GB/T 1040-1992, GB/T 13022-1991 Plastics - Determination of tensile properties - Part 3. Test conditions for films and sheets (ISO 527-3.1995, IDT) Issued on: SEPTEMBER 1, 2006 Implemented on: FEBRUARY 1, 2007 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. 3. No action is required - Full-copy of this standard will be automatically & immediately delivered to your EMAIL address in 0~60 minutes. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Principle... 6 4 Definitions ... 6 5 Apparatus ... 6 6 Test specimens ... 6 7 Number of specimens ... 10 8 Conditioning ... 10 9 Procedure ... 10 10 Calculation and expression of results ... 10 11 Precision ... 10 12 Test report ... 10ForewordGB/T 1040 Plastics - Determination of tensile properties is divided into 5 parts. — Part 1. General principles; — Part 2. Test conditions for moulding and extrusion plastics; — Part 3. Test conditions for films and sheets; — Part 4. Test conditions for isotropic and orthotropic fibre-reinforced plastic composites; — Part 5. Test conditions for unidirectional fibre-reinforced plastic composites. This Part is Part 3 of GB/T 1040, which is equivalent to ISO 527-3.1995 Plastics - Determination of tensile properties - Part 3. Test conditions for films and sheets. For ease of use, the following editorial changes are made in this Part. a) CHANGE “this International Standard” into “this Standard” or “GB/T 1040”, “this Part of ISO 527” into “this Part of GB/T 1040” or “this Part”; b) DELETE the forward of ISO 527-3.1995; c) ADD the forward of national standard; d) REPLACE two of the three international standards in “Normative references” with the corresponding national standards equivalent to these two documents; e) MOVE the note in Subclause 1.2 to Subclause 1.1; f) USE our national decimal symbol “.” to replace the decimal symbol “,” in the international standards; g) The contents of Amendments 1 and 2 of ISO/TC 61/SC 11, respectively, issued in in 1998 and 2001, are incorporated into the text. This Part replaces GB/T 1040-1992 Plastics - Determination of tensile properties and GB/T 13022-1991 Plastics - Determination of tensile properties of films along with other parts. Compared with GB/T 1040-1992, the major changes in this Part are shown in the Foreword of GB/T 1040.1-2006. Compared with GB/T 13022-1991, the major changes in this Part are as follows. — DELETE 1 mm/min, 2 mm/min, 10 mm/min and 30 mm/min from the test speed. ADD 300 mm/min, that is, CHANGE from the original 9 kinds [(1, 2, 5, 10, 30, 50, 100, 200, 500) mm/min] into 6 kinds [(5, 50, 100, 200, 300, 500) mm/min]; — ABOLISH the Type I specimen in the GB/T 13022-1991; — INCORPORATE the Types II, III and IV specimens in the GB/T 13022- 1991 into this Part, and CHANGE the codes of the specimen types into Types 5, 1B and 2, respectively; — ADD Type 4 specimen, whose dimensions are completely different from the Type I specimen before revision; — DELETE the contents related to the modulus determination and calculation; — ADD the “Definition”, “Principle”, “Precision”, etc.; and — ADD more information in the contents of the test report. This Part was proposed by China Petroleum and Chemical Industry Association. This Part shall be under the jurisdiction of the Subcommittee of Methods and Products of the National Technical Committee for Standardization of Plastics (TC 15/SC 4). Responsible drafting organizations of this Part. National Quality Supervision and Inspection Center for Synthetic Resin, National Quality Supervision and Testing Centre of Plastic Product (Beijing), and National Quality Supervision and Testing Centre of Plastic Product (Fuzhou). Participating drafting organizations of this Part. Resin Application Research Institute of Beijing Yanhua Petrochemical Co., Ltd, National Petrochemical Quality Supervision and Inspection Center for Synthetic Resin and Organic Raw Materials, Zhonghao Chenguang Research Institute of Chemical Industry, Guangzhou Kingfa Science and Technology Co., Ltd, Shenzhen SANS Material Detection Co., Ltd, etc. Main drafters of this Part. Zhang Yan, Wang Yongming, He Peng and Liu Shansheng. The previous released editions of the Standards substituted by this Part are as follows. — GB/T 1040-1979, GB/T 1040-1992; and — GB/T 13022-1991. Plastics - Determination of tensile properties – Part 3. Test conditions for films and sheets1 Scope1.1 This Part of GB/T 1040 specifies the test conditions for determining the tensile properties of plastic films or sheets less than 1mm thick, based upon the general principles given in Part 1. Note. For sheets greater than 1mm thick, the user is referred to GB/T 1040.2. 1.2 SEE Subclause 1.2 in GB/T 1040.1-2006. 1.3 This Part is not normally suitable for determining the tensile properties of. a) cellular materials; b) plastics reinforced by textile fibres. 1.4 SEE Subclause 1.5 in GB/T 1040.1-2006.2 Normative referencesThe provisions in the following documents become the provisions of this Part through reference in this Part. For dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this Part. However, parties who reach an agreement based on this Part are encouraged to study if the latest editions of these documents are applicable. For undated references, the latest editions apply to this Part. GB/T 1040.1-2006 Plastics - Determination of tensile properties - Part 1. General principles (ISO 527-1.1993, IDT) GB/T 6672-2001 Plastics - Film and sheeting - Determination of thickness by mechanical scanning (idt ISO 4593.1993) ISO 4591.1992 Plastics - Film and sheeting - Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness)7 Number of specimensSEE Clause 7 in GB/T 1040.1-2006.8 ConditioningSEE Clause 8 in GB/T 1040.1-2006.9 ProcedureSEE Clause 9 in GB/T 1040.1-2006.10 Calculation and expression of resultsSEE Clause 10 in GB/T 1040.1-2006, except for “10.3 Modulus calculation” and “10.4 Poisson’s ratio, μ”.11 PrecisionThe precision of the test method is not known because inter-laboratory data are not available. When inter-laboratory data are obtained, a precision statement will be added at the following revision.12 Test reportThe test report shall include the following information. a) a reference to this Part of GB/T 1040, including the type of specimen and the test speed, written in the following format. Tensile test GB/T 1040.3/1B/50 Type of specimen Test speed b) to q), SEE b) to q) in Clause 12 of GB/T 1040.1-2006. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 1040.3-2006 be delivered?Answer: The full copy PDF of English version of GB/T 1040.3-2006 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 1040.3-2006_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1040.3-2006_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 1040.3-2006 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 1040.3-2006?A step-by-step guide to download PDF of GB/T 1040.3-2006_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 1040.3-2006". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
