GB 25723-2010 English PDFUS$434.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. GB 25723-2010: Utility lighters -- Safety and quality Status: Valid
Basic dataStandard ID: GB 25723-2010 (GB25723-2010)Description (Translated English): Utility lighters -- Safety and quality Sector / Industry: National Standard Classification of Chinese Standard: Y73 Classification of International Standard: 97.180 Word Count Estimation: 22,274 Date of Issue: 2010-12-23 Date of Implementation: 2011-06-01 Adopted Standard: ISO 22702-2003, IDT Regulation (derived from): Announcement of Newly Approved National Standards No. 10 of 2010 (No. 165 overall) Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This Chinese standard applies to point guns (also known as grill lighters, fireplace lighters, ignition rods, gas matches) can produce flames all consumer goods, and similar terms defined 2, 6 ignition device. This standard does not apply to matches, nor does it apply to lit cigarettes, cigars and pipes and other products that produce flames. GB 25723-2010: Utility lighters -- Safety and quality---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Utility lighters.Safety and quality ICS 97.180 Y73 National Standards of People's Republic of China Point guns Safety and Quality (ISO 22702.2003, Utilitylighters-Generalconsumer-safetyrequirements, IDT) Published 2010-12-23 2011-06-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China issued Table of ContentsIntroduction Ⅲ Introduction Ⅳ 1 Scope 1 2 1 Terms and definitions Functional requirements 3 2 4 structural integrity in claim 5 5 Repeat the fuel filling 6 6 Instructions and warnings 6 Test Method 7 9 8 Product labeling 15 Annex A (informative) manufacturer standard limit and additional limits on the flame characteristics in terms of 3.2.2 - 3.2.7 Reception quality limit (AQL) 16 Reference 17ForewordChapter 3 of this standard, Chapter 4, Section 5, Chapter 6, Section 7 is mandatory, the rest are recommended. This standard is identical with ISO 22702.2003 "point guns consumer safety standards" (in English). This standard incorporates ISO 22702.2003/Amd.1.2008 of amendments, the provisions of these amendments has been involved through its Vertical wire outer margin position (‖) were marked. For ease of use, this standard the following editorial changes made. a) use "present standard" instead of "this International Standard"; b) with the symbols instead of decimal decimal symbol "," "."; c) Delete international standards foreword. Appendix A of this standard is an informative annex. The standard proposed by China Light Industry Federation. This standard by the National Standardization Technical Committee hardware (SAC/TC174). This standard is drafted. Ningbo Xinhai Electric Co., Ltd.; participated in the drafting. the State Administration of Quality Supervision, Inspection and Quarantine risk Central Laboratory of dangerous goods, Zhejiang Tiger Lighter Co., Ltd., Ningbo Xingda fire Manufacturing Co., Ltd., Ningbo lighter industry association of Wenzhou City Lighter Industry Association, Hunan People's Republic of China Entry-Exit Inspection and Quarantine Bureau. The main drafters. Wang Libing, Running an, Zhou Dahu, Liu Gang, Lining Tao, Sun Ningwei, Li Jing, Pang Zi.IntroductionThis standard covers commonly referred to as guns point (also referred to as grill lighters, fireplace lighters, ignition rods, gas matches) all produce Consumer flame ignition device and the like. This standard specifies the number of points required guns to ensure that the user during normal use, or Reasonably safe under the foreseeable improper use. Point guns as a tool to produce flame, flame and other sources as potentially harmful to the user. This standard does not exclude all Harm, but try to minimize the potential harm to the user to a minimum. Point guns Safety and Quality Warning. This standard does not point out all of the safety problems associated with the application of this standard. Therefore, before using the standard user's responsibility Establish appropriate safety and health practices, determine the applicable Regulations.1 ScopeThis standard covers commonly referred to as guns point (also referred to as grill lighters, fireplace lighters, ignition rods, gas matches) all produce Consumer flame, and an ignition means defined in terms similar to 2.6. This standard does not apply to matches; does not apply to products for lit cigarettes, cigars and pipes and other produce flame.2 Terms and DefinitionsThe following terms and definitions apply to this standard. 2.1 Combustion valve valve Controlling the fuel supply member and a release point guns. 2.2 Combustion nozzle the orifice The top of the fuel valve to release fuel. 2.3 Flame height flameheight Top visible flame to the linear distance of the barrel. 2.4 Flashover flaring Height change from the stable state to the unstable state of the flame. 2.5 Ignition ignite Operation of the ignition device and a fuel delivery system, the dots in a predetermined manner to produce a flame guns. 2.6 Point guns utilitylighter And a handheld device with manual ignition operation of the ignition system, in the fully extended state, the length is greater than or equal to 100mm, with a filling 2.9 Fuel defined terms, the following items mainly used to ignite, such as candles, fuel fireplace, a carbon type or a gas grill, camping stoves, lanterns, burning Means gas or beacon. 2.7 Adjustable point guns utilitylighter, adjustable A user-flame height can be adjusted by manual operation of the firing gun mode. 2.8 Disposable point guns utilitylighter, disposable Point guns having pre-filling of the fuel, and the user can repeat the filling. 2.9 Fuel fuel 24 ℃ when the vapor pressure exceeds 103kPa normal butane, isobutane, propane, or other liquid hydrocarbons or mixtures thereof. 2.10 Lighter not adjustable utilitylighter, non-adjustable Flame height set by the manufacturer without flame height adjustment means point guns. 2.11 Filling can be repeated spot guns utilitylighter, refilable Refilling the fuel from outside the fuel tank or replaceable point guns. 2.12 Self extinguishing point guns utilitylighter, self-extinguishing Once ignited, the force required to maintain continuous flame, the flame goes out as external termination point guns. 2.13 Non-self-extinguishing point guns utilitylighter, non-self-extinguishing Effective external force need not be applied continuously to sustain a flame upon ignition, but specifically requires manual operation to extinguish the flame point guns. 2.14 Barrel shield Lighter completely or partially encapsulating the structure of the orifice combustion. 2.15 Continuous automatic ignition sustainedself-ignition Since the ignition operation of conscious non-human, for example, drop point guns, resulting in the ignition device is activated, and causes the flame to continue to burn phenomenon. 2.16 Burst fire spitting Splashing fire sputtering Non-atomized fuel splashes or droplets of liquid fuel to the combustion state of a phenomenon of detachment from the main flame. 2.17 The fuel tank fuelreservoir The fuel storage before release. 2.18 Ignition system ignitionsystem The fuel ignited by a spark generating systems, such as a battery or a piezoelectric device. 2.19 Premixing Lighter premixingburnerutilitylighter The fuel and air mix before ignition point guns. 2.20 After mixing type Lighter postmixingburnerutilitylighter The fuel and air at the ignition point of the mixed guns. 2.21 Flame flame Result of the combustion of the fuel, the process generates heat and low light conditions or under normal naked eye can see the light.3 Functional requirements3.1 flame generation To minimize the possibility of accidental ignition and auto-ignition point guns application specially lit manual operation. This operation should be at least Follow one of the following requirements. a) the user needs to operate effectively in order to produce and maintain a flame combustion system; b) two or more times the user needs to operate independently of the system to produce a flame; c) generating a flame force required should be equal to or greater system 15N (see FIG. 1 in test mode). Press 3.1c FIG. 1) generate a sample measured as described flame detection apparatus operation force 3.2 flame height 3.2.1 General The maximum point guns can reach the flame height should, or both, by way limit set in advance or product design. To be Adjustable point guns, in the first operation of the user, the initial flame height should be restricted. These limits shall comply with the provisions of 7.1 Provisions. After the mixed-type non-adjustable 3.2.2 Lighter After mixing type utility lighter can not be adjusted for the terms defined by the terms of 2.10 and 2.20, in the hands of a user, in accordance with the terms of Test 7.1 , The maximum flame point guns in the vertical upward direction height should not exceed 100mm. See Appendix A reception quality in Chapter A.1 Limit the number of reference samples (the AQL) and references therein. 3.2.3 can not be adjusted before mixing formula Lighter You can not be adjusted before mixing for spot guns defined terms and provisions 2.10 2.19, in the hands of a user, in accordance with the terms of Test 7.1 , The maximum flame point guns in the vertical upward direction height should not exceed 75mm. See Appendix A reception quality in Chapter A.1 Limit the number of reference samples (the AQL) and references therein. 3.2.4 adjustable spot mixed guns After mixing for spot guns can be adjusted 2.7 and terms defined in terms of 2.20, when a user intentionally adjusted to a high manufacturer's maximum flame Of the design limits, in accordance with the terms of test time of 7.1, the flame point guns in the vertical upward direction height should not exceed 150mm. See attached A record in Chapter A.1 reception quality limit (the AQL) the number of reference samples and the reference literature. 3.2.5 adjustable front spot mixed guns 2.7 for terms and conditions defined in 2.19 adjustable front spot mixed guns, high when a user intentionally adjusted to the manufacturer's maximum flame Of the design limits, in accordance with the terms of test time of 7.1, the flame point guns in the vertical upward direction height should not exceed 75mm. See attached A record in Chapter A.1 reception quality limit (the AQL) the number of reference samples and the reference literature. 3.2.6 adjustable rear-mixing point guns (first ignition flame height) For mixed-type point guns after 2.7 Terms and conditions can be defined by regulation 2.20, the manufacturer shall regulate the height of the flame point guns, user First firing does not change the position adjustment means, according to the terms of 7.1 test, flame point guns in the vertical upward direction height of more than 100mm. See Appendix A with reference to the number of samples in the reception quality limit (the AQL) Chapter A.1 and references therein. 3.2.7 adjustable front spot mixed guns (first ignition flame height) Terms and conditions for 2.7 2.19 defined adjustable front mixing type point guns, the manufacturer shall regulate the height of the flame point guns, user First firing does not change the position adjustment means, according to the terms of 7.1 test, flame point guns in the vertical upward direction height of more than 60mm. See Appendix A with reference to the number of samples in the reception quality limit (the AQL) Chapter A.1 and references therein. 3.2.8 adjustable rear mixed guns spot (the minimum height of the flame in the set) After mixing for spot guns can be adjusted 2.7 and terms defined in terms of 2.20, it is adjusted to a minimum when the user manufacturers to design high flame When degrees, according to the terms of test 7.1, point guns in a vertically upward direction to reach the height of the flame should not exceed 75mm. 3.2.9 adjustable front spot mixed guns (set the lowest flame height) Flame definition for terms and conditions 2.7 2.19 Height adjustable front spot mixed guns, when the user adjusts the manufacturer design most Small flame height, according to the terms of test time of 7.1, the flame point guns in the vertical upward direction should be not more than 50mm. 3.3 Flame height adjustment 3.3.1 2.7 Terms defined flame height adjustable point guns, in normal use, the user should deliberately action requires To be able to reduce or increase flame height. 3.3.2 If the flame point guns guns surface height adjusting apparatus prominent points in the entire operating range, should be at least 1N force Adjusting the tangential direction (see FIG. 2). Example 2 is applied to predetermined flame height adjustment 3.3.2 described force detection apparatus of FIG. 3.3.3 For the flame vertical flame rotary adjusting device adjustable point guns, should be able to do the following. a) a flame guns point adjustment means fixed to the vertically upward flame, fire adjusting means facing the user, the adjusting knob should drop Zuo Xuan Low flame height; Lighter adjustable b) a flame in a direction parallel to the axis direction of the flame adjusting means adjusting the flame, should be able to increase the movement direction Save flame height; c) If the flame adjusting means located at the bottom point of guns, the user faces the thermal transfer means should reduce the flame adjustment knob clockwise height. Adjustable point guns should be decreased or increased with the flame flag represents the required apparatus the direction of motion of the height adjustment. Adjusting means It indicates a direction to be permanently engraved or printed on the point guns. These tags should be located near the point of the flame guns adjusting means, the user should clearly see And to understand. 3.4 Fire Blast, fire and flashover splash 2.6 to point guns tested in accordance with the terms defined in clause 7.2, there should be provided in the flame height 2.16 at maximum flame height Burst fire-defined models, splashing fire or 2.4 Terms defined flashover. 3.5 flame goes out 3.5.1 adjustable spot mixed guns After the test spot mixed guns adjustable, the maximum flame height provided at a position in accordance with the terms of 7.3, after combustion 10s, when Lighter When turned off in a predetermined manner, such as a release button or lever, any flame is extinguished completely exposed in the 3s. For mixing after the barrel has a spot Guns, burning time delay allows for increased 3s, but during the flame should not exceed barrel. 3.5.2 adjustable and non-adjustable spot mixed guns 7.3 according to the terms of the mixed-type point guns can be adjusted, the flame height provided at a position 100mm (when the maximum flame height of less than or When 100mm, the maximum flame height is provided at its flame height position), or permanent set after the non-adjustable flame height mixed guns for spot Test, combustion 20s, when the point guns extinguished in a predetermined manner, such as a release button or lever, any exposed flame is completely put in the 3s Off. For mixing after the barrel has a spot guns, allowing increased burning time delay 3s, but should not exceed the flame during the barrel. 3.5.3 adjustable and non-adjustable premixing Lighter 7.3 in accordance with the provisions of the adjustable front spot mixed guns, flame height provided at the position 75mm (or when the maximum flame height of less than 75mm When the flame height provided maximum flame height), the height of the flame front or permanently set mixing type test point guns, post-combustion 20s, when the point When the guns off in a predetermined manner, such as a release button or lever, any exposed flame should be extinguished in the 6s. Note. All 6s delay burning time specified in this standard, will regularly reconsider, with the technological advances gradually reduced. 3.6 volumetric displacement Treat delivery point guns be tested in accordance with clause 7.11, the proportion of the liquid portion of utility lighter fuel should not exceed the total volume of the fuel tank 85%. Structural integrity in claim 4 4.1 General Point guns should have the complete structure of the provisions of clause 4.2 to 4.9. 4.2 drop resistance 4.2.1 7.4 according to the terms of the clause 2.6 Lighter-defined test point guns should withstand 3 times the height of (1.5 ± 0.1) m down Off, the fuel tank rupture does not occur, there are no defined in terms of duration 2.15 auto-ignition, fuel leakage rate of less than 15mg/min and It does not affect the subsequent safe to use. 4.2.2 4.2.1 comply with the terms and to point guns lit in a predetermined way, shall comply with the provisions of 3.1 to 3.5 (including 3.1 and clause 3.5) Regulation Given all the requirements. 4.2.3 can not point guns lit in a predetermined manner deemed qualified. 4.3 resistance to high temperature 7.5 4.3.1 tested in accordance with the terms of point guns should be subjected to a temperature of 65 deg.] C for 4h. 4.3.2 4.3.1 compliance terms and ignite the point guns in a predetermined manner after stable at (23 ± 2) ℃ environment, should be subject to the terms All requirements of 3.1 to 3.5 (including the terms of 3.1 and 3.5). 4.4 Combustion behavior 4.4.1 flame height provided maximum flame height position adjustable point guns, or permanently set non-adjustable flame height of ignition Gun, 10s should be subjected to the following two different positions of combustion. a) Flame vertically upward; b) inclined downward flame 45 ° angle from horizontal. 4.4.2 First flame point guns vertically upward combustion test, the combustion should not occur any member or lead to dangerous situations Deformation. 4.4.2 and 4.4.3 with the terms can be ignited in a predetermined way point guns, at (23 ± 2) ℃ ambient stable after 5min, the flame Inclined at 45 ° to the horizontal test, as shown in FIG. It should not be any member or lead to dangerous situations combustion modification. The position of the test sample according to FIG. 3 described combustion 4.4.3 4.5 Anti-sustained combustion Test in accordance with clause 7.6, point guns should withstand continuous burning 2min, and should not lead to dangerous situations. 4.6 Anti-cycle combustion Tested in accordance with clause 7.7, point guns should withstand combustion 20s, the combustion cycle is repeated 10 times. 4.7 Appearance When a point of use or holding guns in a predetermined manner, the surface should point guns may be caused by sharp edges with a user scratches or wear. 4.8 Fuel Compatibility Tested in accordance with the terms of 7.8, 2.6 point guns terms defined in prolonged contact with the manufacturers recommend the use of a fuel component which is not It should damage deterioration, so that the point guns do not meet the standards or cause gas leakage rate exceeds 15mg/min. 4.9 The anti-press 7.9 tested in accordance with the terms of, the fuel tank should withstand point guns firing gun manufacturers recommend the use of fuel generated at two times 55 ℃ Vapor pressure. Repeated filling of the fuel 5 5.1 2.11 reusable terms defined by filling spot guns, application and should contain clear instructions for use and warnings in Chapter 6. 5.2 when tested in accordance with the terms of 7.10, repeatable filling spot guns repeated recharging valve should be reliable, the gas leakage rate of no more than 15mg/min.6 Instructions and warnings6.1 Safety Information 6.1.1 General All point guns with safety information should be the proper use of the expression (such as instructions or warnings, or both), with text Safety or symbolic form to replace all existing text instructions and warnings, or both are used, the use of the correct report Appeal to the user. 6.1.2 Location Safety information should be on the point guns gun, or on the packaging with the product instructions and manuals, point of sale or at the time of sale of product packaging on. Style safety information should be emphasized that such a warning is ideal for point guns. This safety information should be clearly marked on the position, background color Color, size, style should be a clear distinction with other information. 6.1.3 Content 6.1.3.1 For all point guns, should be specially marked word "Warning" in the Security Information Service. 6.1.3.2 For ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB 25723-2010_English be delivered?Answer: Upon your order, we will start to translate GB 25723-2010_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB 25723-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB 25723-2010_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
