GB/T 1682-2014 PDF EnglishUS$70.00 · In stock · Download in 9 seconds
GB/T 1682-2014: Rubber, Vulcanized - Determination of Low temperature Brittleness - Single Test Piece Method Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 1682: Historical versions
Similar standardsGB/T 1682-2014: Rubber, Vulcanized - Determination of Low temperature Brittleness - Single Test Piece Method---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT1682-2014 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.060 G 40 Replacing GB/T 1682-1994 Rubber, Vulcanized - Determination of Low- temperature Brittleness - Single Test Piece Method Issued on. DECEMBER 31, 2014 Implemented on. JULY 1, 2015 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative References... 5 3 Terms and Definitions... 5 4 Test Equipment... 6 5 Sample... 8 6 Laboratory Temperature... 8 7 Test Procedure... 8 8 Test Result and Processing... 9 9 Test Report... 10ForewordThis Standard was drafted in accordance with the rules in GB/T 1.1-2009. This Standard serves as a replacement of GB/T 1682-1994 Rubber, Vulcanized - Determination of Low-temperature Brittleness (single test piece method). In comparison with GB/T 1682-1994, there are several main technical changes as follows. ---In order to satisfy the requirements of material testing and simplify test procedure, test procedure B is added, namely, the method of impacting test sample at a stipulated temperature and judging whether any fail is caused (please refer to Chapter 1; 7.2; 8.2; Chapter 9); ---“fail” is used to replace “embrittlement” (please refer to 3.2; 3.2 in Version 1994); ---“lifting device” is used to replace “lifting poker and lifting spring” (please refer to 4.1; 4.1 in Version 1994); ---Figure 1 is re-drawn; the title and keys of the figure are added (please refer to 4.1; 4.1 in Version 1994); ---The selection of cooling mode is added, namely, in the selection of refrigerant, except from dry ice and liquid nitrogen, other cooling modes may also be adopted (please refer to 4.4.2; 4.4.2 in Version 1994); ---Sample thickness is modified from (2.0 ± 0.3) mm into (2.0 ± 0.2) mm (please refer to 5.1; 5.1 in Version 1994); ---The requirement of sample temperature regulation and surface inspection before test is added (please refer to 5.2; 5.2 in Version 1994); ---The requirement “adjust to the needed temperature, or, slightly lower than the needed temperature, so that after sample is immersed, the temperature of freezing medium is exactly the needed temperature” is added (please refer to 7.1.2; 7.2 in Version 1994); ---The requirement “after the impact, take down the sample, place it still for at least 30 s, then, wipe off residual liquid on the sample surface, bend it; under bright light, observe whether the sample is failed, and record it” is added (please refer to 7.1.6; 7.6 in Version 1994); ---The content “test report shall include detailed description and the source of sample” is added (please refer to Chapter 9; Chapter 9 in Version 1994). This Standard was proposed by China Petroleum and Chemical Industry Association (CPCIA). This Standard shall be under the jurisdiction of General Test Method Subcommittee, National Technical Committee 35 on Rubber and Products of Standardization Administration of China (SAC/TC 35/SC 2). The drafting organizations of this Standard. AECC Beijing Institute of Aeronautical Materials, Jiangsu RONGCHANG Machinery Manufacturing Group Co., Ltd., Changzhou LANGBO Auto Parts Co., Ltd., Qingdao Rubber Six Conveyor Belt Co., Ltd., Beijing Research & Design Institute of Rubber Industry, Jiangsu Mingzhu Testing Machinery Co., Ltd. The main drafters of this Standard. Zhuhua, Zhang Juhua, Ding Feixia, Huang Shundao, Zhang Meiling, Zhangfeng, Yaofeng, Xie Junfang, Lijing, Zhuming. The issuing of previous versions of the standard replaced by this Standard is as follows. ---GB/T 1682-1979, GB/T 1682-1982, GB/T 1682-1994. Rubber, Vulcanized - Determination of Low- temperature Brittleness - Single Test Piece Method Warning. personnel adopting this Standard shall have practical experience of working in a regular laboratory. This Standard does not point out all the possible safety issues. Users of this Standard shall undertake the responsibility of adopting proper safety and health measures; guarantee the compliance with conditions stipulated in relevant national laws and regulations.1 ScopeThis Standard stipulates the method of adopting single test piece brittleness temperature testing machine to test vulcanized rubber’s brittleness temperature and judging whether vulcanized rubber is failed after being impacted at a stipulated temperature. The method includes two procedures. Procedure A is applicable to the test of brittleness temperature; Procedure B is applicable to the judgment of whether fail is caused after the impact at a stipulated temperature. NOTE. the brittleness temperature tested in this Standard is characteristic temperature of vulcanized rubber. It does not represent the lower limit of operating temperature of vulcanized rubber and its products. Through brittleness temperature, the strengths and weaknesses of low-temperature performance of different rubber materials or different formulas of vulcanized rubber may be compared. Therefore, in the quality inspection and production process control of rubber materials and their products, it is of certain practical value.2 Normative ReferencesThe following documents are indispensable to the application of this document. In terms of references with a specific date, only versions with the specific date are applicable to this document. In terms of references without a specific date, the latest versions (including all the modification orders) are applicable to this document. GB/T 2941-2006 Rubber - General Procedures for Preparing and Conditioning Test Pieces for Physical Test Methods (ISO 23529.2004, IDT)3 Terms and DefinitionsThe following terms and definitions are applicable to this document. 3.1 Brittleness Point (single test piece method) Brittleness point refers to the highest temperature when sample is failed after being impacted under certain conditions.4 Test Equipment4.1 Composition Equipment is constituted of workbench, lifting clamp holder, impact device, low- temperature thermometer, cryogenic container which holds freezing medium, and blender, etc. 4.2 Lifting Clamp Holder Lifting clamp holder is constituted of clamp and lifting device. The distance from the impacted part of sample, to the lower end of the clamp is (11.0 ± 0.5) mm, as it is shown in Figure 1. 4.3 Impact Device Impact device is constituted of impactor and impact spring, etc. 4.4 Low-temperature Thermometer Adopt low-temperature thermometer, whose minimum division value is not more than 1 °C, to test the temperature of freezing medium. Low-temperature thermometer, thermocouple and resistance thermometer may be used. Low-temperature thermometer shall be internal standard type of semi-dipping. 4.5 Freezing Medium Freezing medium is prepared by appropriate heat-transfer medium and refrigerant. 4.5.1 Heat-transfer medium At test temperature, liquid that can maintain its flowability and exert no additional influence on sample may be considered as heat-transfer medium. Generally speaking, this type of heat-transfer medium uses ethanol, and also, acetone and siloxane, etc.5 Sample5.1 Specification Sample length. (25.0 ± 0.5) mm; width. (6.0 ± 0.5) mm; thickness. 5.2 Requirements Before test, sample shall be placed and adjusted at standard laboratory temperature for at least 3 h.6 Laboratory TemperatureLaboratory temperature shall comply with relevant stipulations in GB/T 2941-2006.7 Test Procedure7.1 Procedure A 7.1.1 Test preparation. lower the lifting clamp holder; place the low-temperature thermometer; place the thermometer’s temperature measurement point in the same horizontal position as the lower end of the clamp. Inject heat-transfer medium into the cryogenic container; the injection volume shall guarantee that the distance from the lower end of the clamp to the liquid level is (75 ± 10) mm. 7.1.4 Lower the lifting clamp holder. Start to freeze the sample, meanwhile, start the timing. The stipulated freezing time is. During sample freezing time, temperature fluctuation of the freezing medium shall not exceed ± 1 °C. 7.1.5 Raise the lifting clamp holder; make the impactor impact the sample within 0.5 s. 7.1.6 Take down the sample; place it still for at least 30 s. Then, wipe off residual liquid on the sample surface. In accordance with the impact direction, bend the sample into 180°. Under bright light, meticulously observe whether there is any fail; record it. When the sample is failed, record the specific phenomena of the fail. 7.2 Procedure B Conduct the test in accordance with the steps in 7.1.1 ~ 7.1.6.A group of test needs at least 3 samples.8 Test Result and Processing8.1 Procedure A 8.2 Procedure B If no sample manifests fail in a group of samples, then, the test result is non-fail. If 2 or more than 2 samples manifest fail in a group of samples, then, the test result fails.9 Test ReportTest report shall include the following content. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 1682-2014 be delivered?Answer: The full copy PDF of English version of GB/T 1682-2014 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 1682-2014_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1682-2014_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 1682-2014 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 1682-2014?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 1682-2014 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 1682-2014?A step-by-step guide to download PDF of GB/T 1682-2014_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 1682-2014". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
