YY/T 0969-2023 PDF EnglishUS$200.00 · In stock · Download in 9 seconds
YY/T 0969-2023: Single-use medical face mask Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid YY/T 0969: Historical versions
Similar standardsYY/T 0969-2023: Single-use medical face mask---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/YYT0969-2023YY MEDICAL INDUSTRY STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 11.140 CCS C 48 Replacing YY/T 0969-2013 Single-use medical face mask Issued on: NOVEMBER 22, 2023 Implemented on: DECEMBER 01, 2025 Issued by. National Medical Products Administration Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Terms and definitions... 5 4 Technical requirements... 6 5 Test methods... 7 6 Marks... 10 7 Packaging, transportation and storage... 11 Bibliography... 12ForewordThis document was drafted in accordance with the rules given in GB/T 1.1-2020 "Directives for standardization - Part 1.Rules for the structure and drafting of standardizing documents". This document replaces YY/T 0969-2013 "Single-use medical face mask". Compared with YY/T 0969-2013, in addition to the structural adjustments and editorial modifications, the main technical changes in this document are as follows. a) Change the definition for "bacterial filtration efficiency" (see 3.1 of this Edition; 3.1 of Edition 2013); b) Change the definition for "airflow resistance" (see 3.2 of this Edition; 3.2 of Edition 2013); c) Change the requirements for "appearance" (see 4.1 of this Edition; 4.1 of Edition 2013); d) Change the requirements for "structure and dimensions" (see 4.2 of this Edition; 4.2 of Edition 2013); e) Change the requirements for "nose clip" (see 4.3 of this Edition; 4.3 of Edition 2013); f) Change the requirements for "mask strap" (see 4.4 of this Edition; 4.4 of Edition 2013); g) Change the requirements for "airflow resistance" (see 4.6 of this Edition; 4.6 of Edition 2013); h) Change the requirements for "microbiological indicators" (see 4.7 of this Edition; 4.7 of Edition 2013); i) Change the requirements for "cytotoxicity" (see 4.9.1 of this Edition; 4.9.1 of Edition 2013); j) Change the test method for "nose clip" (see 5.3 of this Edition; 5.3 of Edition 2013); k) Change the test method for "mask strap" (see 5.4 of this Edition; 5.4 of Edition 2013); l) Change the test method for "airflow resistance" (see 5.6 of this Edition; 5.6 of Edition 2013); m) Change the test method for "microbiological indicators" (see 5.7 of this Edition; 5.7 of Edition 2013); n) Change the test method for "ethylene oxide residual amount" (see 5.8 of this Edition; 5.8 of Edition 2013); o) Change the test method for "biocompatibility" (see 5.9 of this Edition; 5.9 of Edition 2013); p) Change "marks" (see Chapter 6 of this Edition; Chapter 6 of Edition 2013). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. The issuing authority shall not be held responsible for identifying any or all such patent rights. This document was proposed by National Medical Products Administration. This document shall be under the jurisdiction of National Standardization Working Group on Medical Protective Equipment (SAC/SWG 30). The drafting organizations of this document. Beijing Institute of Medical Device Inspection (Beijing Medical Biological Protective Equipment Inspection and Research Center), Guangdong Institute of Medical Device Quality Supervision and Inspection, Xinjiang Uygur Autonomous Region Drug Inspection Institute (Xinjiang Uygur Autonomous Region Medical Device Inspection and Testing Center), Beijing University of Chemical Technology, Jiangxi 3L Medical Products Group Co., Ltd., Yadu Holding Group Co., Ltd., Wenjiang Medical Products Co., Ltd., Zhende Medical Products Co., Ltd., Ogilvy Medical Products Co., Ltd., Ningbo Kangjiale Medical Equipment Co., Ltd. Main drafters of this document. Liu Simin, Luo Qingxiang, Sun Peng, Wang Dan, Tong Xiaofeng, Liu Mingyu, Yang Xiaomeng, Chen Ming, Cao Mengjie, Huang Lihao, Liu Keyang, Huang Yongfu, Zhang Yaping, Zhao Dan, Li Hua, Zhang Juan, Li Jian, Li Yueling, Hu Guangyong. Versions of standard substituted by this document are. - YY/T 0969-2013 that was first issued in 2013; - This is the first revision. Single-use medical face mask1 ScopeThis document specifies the technical requirements, test methods, marks, packaging, transportation and storage for single-use medical face mask. This document is applicable to single-use face masks that cover the user's mouth, nose and jaw, and are worn in general medical environments to block exhaled or sprayed pollutants from the oral and nasal cavities. This document does not apply to medical protective masks and medical surgical masks.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 14233.1-2022, Test methods for infusion, transfusion, injection equipment for medical use -- Part 1.Chemical analysis methods GB/T 16886.5, Biological evaluation of medical devices -- Part 5.Tests for in vitro cytotoxicity GB/T 16886.10, Biological evaluation of medical devices -- Part 10.Tests for irritation and skin sensitization GB/T 16886.12, Biological evaluation of medical devices -- Part 12.Sample preparation and reference materials YY 0469, Sterile drainage catheters and accessory devices for single use Part IV of Edition 2020 of the Pharmacopoeia of the People's Republic of China3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply. 3.1 bacterial filtration efficiency; BFE Under specified testing conditions, the mask's ability to filter out bacteria-containing suspended particles. NOTE. It is usually expressed as a percentage. 3.2 airflow resistance The resistance of the mask under the specified area and specified flow rate. NOTE. It is expressed as pressure difference per unit area.4 Technical requirements4.1 Appearance The mask shall be clean in appearance and in good shape. There shall be no obvious defects such as damage, stains, sharp protrusions, etc. on the surface. 4.2 Structure and dimensions After the mask is worn, it shall cover the wearer's mouth, nose and chin. It shall comply with the marked dimensions and allowable deviations specified by the manufacturer. The design of the mask shall be able to distinguish its inner and outer sides. 4.3 Nose clip 4.3.1 The mask shall be equipped with a nose clip or a structure that replaces the nose clip. 4.3.2 The structure of the nose clip or nose clip replacement shall be such that the mask can be effectively fixed on the nose and fit well to the nose area. The length of the nose clip shall be no less than 50% of the marked length on the side where the nose clip is located. 4.4 Mask strap 4.4.1 Earhook mask The sum of the breaking strengths of each mask strap and the two connection points between each mask strap and the mask body shall not be less than 15 N. 4.4.2 Strap mask The breaking strength of each mask strap and the connection between each mask strap and the mask body shall be no less than 10 N. If there is no fixed connection point between the mask strap and the mask body, the breaking strength of each mask strap shall be no less than 10 N. 4.5 Bacterial filtration efficiency (BFE) The bacterial filtration efficiency of the mask shall be no less than 95%. 4.6 Airflow resistance The airflow resistance for gas exchange on both sides of the mask shall be less than 40 Pa. 4.7 Microbial indicators 4.7.1 Microbiological limits (products supplied in a non-sterilized manner) The total number of microorganisms shall be ≤30 CFU/g. 4.7.2 Sterility (products supplied in a sterilized manner) Masks shall undergo a confirmed sterilization process and the product shall be sterile. 4.8 Residual amount of ethylene oxide (if applicable) If the mask has been sterilized or disinfected with ethylene oxide, the residual ethylene oxide content shall not exceed 10 μg/g. 4.9 Biocompatibility5 Test methods5.1 Appearance Carry out the test on at least 3 samples. Conduct visual inspection. 5.2 Structure and dimensions Carry out the test on at least 3 samples. Actually wear it and measure it with a general or special measuring tool. 5.3 Nose clip Carry out the test on at least 3 samples. Conduct visual inspection. Measure with general or special measuring tools, and perform actual wearing. 5.4 Mask strap 5.4.1 Earhook mask Carry out the test on at least 3 samples. Fix the main part of the mask above the two connection points of the test mask strap so that the mask maintains its natural shape and the two connection points are horizontal. Apply a static pulling force of 15 N in the middle of the mask belt to make the mask strap and the mask body in the same plane, as shown in Figure 1a). Maintain 5 s. Take the other side of the same mask and repeat the above test. If the sample mask strap and any connection points are not disconnected, the breaking strength is recorded as ≥15 N. If disconnection occurs, record the disconnection location (mask strap or connection point) and the breaking strength < 15 N. 5.4.2 Strap mask Carry out the test on at least 3 samples. Fix the mask body so that the mask strap and the mask body are on the same plane. Apply a static pulling force of 10 N to the end of the mask strap in the direction shown in Figure 1b). Maintain 5 s. Take the other side of the same mask and repeat the above test. If the sample mask straps and connections are not disconnected, the breaking strength is recorded as ≥10 N. If disconnection occurs, record the disconnection location (mask strap or connection) and the breaking strength < 10 N. If there is no fixed connection between the mask strap and the mask body, the mask strap shall be removed. One end is fixed, and the other end is loaded with a static tension force of 10 N. Maintain 5 s. If the mask strap is not broken, the breaking strength is recorded as ≥10 N. If breakage occurs, record the breaking strength as < 10 N. 5.5 Bacterial filtration efficiency (BFE) Carry out the test on at least 3 samples. The test method is carried out according to the test method for bacterial filtration efficiency in YY 0469.Determine whether the results meet the requirements of 4.5. 5.6 Airflow resistance Number of samples. use at least 5 samples for testing. Test process. the test location shall be at the center of the mask (mouth and nose when worn). Select 3 non-overlapping test areas. The gas flow rate for testing needs to be adjusted to (8.0±0.2) L/min. The diameter of the sample test area is 25 mm. The test area is 4.9 cm2. Calculate airflow resistance (ΔP) according to formula (1). Results are reported as pressure difference per square centimeter of area (Pa). If the calculated average of the results of the three test areas of each sample meets the requirements of 4.6, it will be judged to be qualified. 5.7 Microbial indicators 5.7.1 Microbial Limits The test is conducted in accordance with the membrane filtration method specified in Microbial Enumeration Method in Microbial Limit Examination of Non-sterile Products (General Chapter 1105) in Part IV of Edition 2020 of the Pharmacopoeia of the People's Republic of China. The total number of aerobic bacteria, mold and yeast is added together. Preparation of test solution. At least 2 minimum packages are randomly selected. Take no less than 10 g of the test sample. Cut into pieces and use a diluent containing 0.1% (mL/mL) polysorbate 80 (or other non-bacterial surfactant), such as pH 7.0 sterile sodium chloride-peptone buffer, or pH 7.2 phosphate. buffer, or 0.9% sterile sodium chloride solution. Prepare a 1.50 (g/mL) test solution. Mix thoroughly. 5.7.2 Sterility Carry out in accordance with the test methods specified in the Sterility Inspection Act (General Chapter 1101) in Part IV of Edition 2020 of the Pharmacopoeia of the People's Republic of China. The treatment of the test article and the inoculation culture medium shall be carried out according to the provisions of dressing the test article in the direct inoculation method.6 MarksThe minimum sales unit of masks shall have clear Chinese marks. The mark shall at least include. a) product name; b) model, specifications and information showing dimensions; c) production date and/or batch number; d) use period or expiration date; e) manufacturer’s name and contact information; f) product technical requirement number; g) product registration certificate number; h) identification of the inner and outer sides and instructions on how to wear them; i) storage conditions; j) "single-use" words or symbols; k) if it is a sterilized product, there shall be a corresponding sterilization mark, and the sterilization method used shall be indicated; l) scope of application.7 Packaging, transportation and storage7.1 Packaging 7.1.1 Masks shall be packaged to prevent mechanical damage and contamination before use. 7.1.2 If ethylene oxide is used for disinfection or sterilization, the packaging shall be made of breathable materials. 7.2 Transportation and storage Carry out in accordance with the conditions stipulated in the contract or the requirements of the instructions for use. Bibliography ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of YY/T 0969-2023 be delivered?Answer: The full copy PDF of English version of YY/T 0969-2023 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of YY/T 0969-2023_English with my colleagues?Answer: Yes. The purchased PDF of YY/T 0969-2023_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- YY/T 0969-2023 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version YY/T 0969-2023?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version YY/T 0969-2023 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of YY/T 0969-2023?A step-by-step guide to download PDF of YY/T 0969-2023_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "YY/T 0969-2023". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
