YD/T 2722-2014 PDF EnglishUS$370.00 · In stock · Download in 9 seconds
YD/T 2722-2014: RF technical requirements and test methods for 60GHz radio equipment Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsYD/T 2722-2014: RF technical requirements and test methods for 60GHz radio equipment---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/YDT2722-2014YD COMMUNICATION INDUSTRY STANDARD ICS 33.060.20 M 36 RF technical requirements and test methods for 60GHz radio equipment Issued on. OCTOBER 14, 2014 Implemented on. OCTOBER 14, 2014 Issued by Ministry of Industry and Information Technology of PRC Table of ContentsForeword... 3 1 Scope... 4 2 Normative references... 4 3 Terms, definitions and abbreviations... 4 3.1 Terms and definitions... 4 3.2 Abbreviations... 5 4 Technical requirements... 5 4.1 Environmental requirements... 5 4.2 Conformity requirements... 6 5 Test method... 8 5.1 Environmental conditions of the test... 8 5.2 Test results and uncertainty... 8 5.3 Test configuration... 9 Appendix A (Normative) Test field for radiation test... 19 Appendix B (Normative) General test method for radiated spurious... 21 References... 23ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard shall be under the jurisdiction of China Communications Standards Association. Drafting organizations of this standard. National Radio Monitoring Center Testing Center, ZTE Corporation, Telecommunication Research Institute of the Ministry of Industry and Information Technology. The main drafters of this standard. Liu Xiaoyong, Song Qizhu, Lin Lei, Wang Junfeng, Xu Ling, Wang Hongbo, Tao Hongbo, Zhang Mingyuan, Zhang Junchi. RF technical requirements and test methods for 60GHz radio equipment1 ScopeThis standard specifies the technical requirements and test methods for the equivalent isotropic radiation power, antenna port output power, transmitter spurious emission, receiver spurious emission, carrier frequency tolerance, out- of-band emission for radio equipment operating in the 60 GHz frequency band. This standard applies to radio equipment operating in the frequency range of 59 GHz ~ 64 GHz.2 Normative referencesThe following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this standard. For undated references, the latest version (including all amendments) applies to this document. GB 9254-2008 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement ITU-R SM.1539-1 (2002) Variation of the boundary between the out-of-band and spurious domains required for the application of Recommendations ITU- R SM.1541 and ITU-R SM. 3293 Terms, definitions and abbreviations3.1 Terms and definitions The following terms and definitions apply to this document. 3.2 Abbreviations The following abbreviations apply to this document.4 Technical requirements4.1 Environmental requirements The equipment manufacturer shall declare in advance the environmental conditions under which the equipment works; the equipment shall work in its nominal working environment. 4.2 Conformity requirements 4.2.1 Peak equivalent isotropic radiated power 4.2.2 Average equivalent isotropic radiated power 4.2.2.1 Overview The product of the average power output to the antenna relative to the antenna gain of the isotropic antenna in the specified direction. 4.2.3.1 Overview The peak power output to the antenna port. 4.2.3.2 Limit When the transmitter is working at the maximum power level, the antenna port output power’s limit is 10 dBm. 4.2.4 Transmitter’s spurious emissions 4.2.4.2 Limit value The transmitter spurious limits are as shown in Table 2. 4.2.5 Receiver spurious emissions 4.2.5.1 Overview Receiver spurious emission refers to the unwanted emission in the spurious domain when the device is in the receiving state. 4.2.6 Carrier frequency tolerance 4.2.6.1 Overview Frequency range Transmit state limit Transmitter standby or idle state a Test bandwidth 4.2.7 Out-of-band emission 4.2.7.1 Overview The out-of-band emission in this standard specifically refers to the maximum power spectral density of the transmitter in the frequency range of 57 GHz ~ 59 GHz and 64 GHz ~ 66 GHz. 4.2.7.2 Limit value The out-of-band emission limit is. -5 dBm/MHz 4.2.8 Integrated antenna The device shall have an integrated antenna structure, to prevent users from disassembling the integrated antenna and installing antenna connectors to replace other antennas during use.5 Test method5.1 Environmental conditions of the test The test items as defined in this standard shall be carried out under normal working environmental conditions. These environmental conditions shall be within the limit operating environment stated by the manufacturer. 5.3 Test configuration 5.3.1 Product Information The device under test shall provide the following information before the start of the test. 5.3.2 Modulation method, frequency and configuration 5.3.2.1 Modulation method The test modulation used shall be representative of the normal use of the equipment. If the equipment cannot conduct continuous emission during normal use, the test shall be able to ensure. 5.3.3 Peak equivalent isotropic radiated power The peak equivalent isotropic radiated power shall be measured using the test field as described in Appendix A and the method in Appendix B. 5.3.6 Transmitter spurious emissions 5.3.6.1 Configuration requirements Transmitter's unwanted emissions shall be measured using the test field as described in Appendix A and the method in Appendix B. YD/T 2722-2014 YD COMMUNICATION INDUSTRY STANDARD ICS 33.060.20 M 36 RF technical requirements and test methods for 60GHz radio equipment Issued on. OCTOBER 14, 2014 Implemented on. OCTOBER 14, 2014 Issued by Ministry of Industry and Information Technology of PRCTable of ContentsForeword... 3 1 Scope... 4 2 Normative references... 4 3 Terms, definitions and abbreviations... 4 3.1 Terms and definitions... 4 3.2 Abbreviations... 5 4 Technical requirements... 5 4.1 Environmental requirements... 5 4.2 Conformity requirements... 6 5 Test method... 8 5.1 Environmental conditions of the test... 8 5.2 Test results and uncertainty... 8 5.3 Test configuration... 9 Appendix A (Normative) Test field for radiation test... 19 Appendix B (Normative) General test method for radiated spurious... 21 References... 23ForewordThis standard was drafted in accordance with the rules given in GB/T 1.1-2009. This standard shall be under the jurisdiction of China Communications Standards Association. Drafting organizations of this standard. National Radio Monitoring Center Testing Center, ZTE Corporation, Telecommunication Research Institute of the Ministry of Industry and Information Technology. The main drafters of this standard. Liu Xiaoyong, Song Qizhu, Lin Lei, Wang Junfeng, Xu Ling, Wang Hongbo, Tao Hongbo, Zhang Mingyuan, Zhang Junchi. RF technical requirements and test methods for 60GHz radio equipment1 ScopeThis standard specifies the technical requirements and test methods for the equivalent isotropic radiation power, antenna port output power, transmitter spurious emission, receiver spurious emission, carrier frequency tolerance, out- of-band emission for radio equipment operating in the 60 GHz frequency band. This standard applies to radio equipment operating in the frequency range of 59 GHz ~ 64 GHz.2 Normative referencesThe following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this standard. For undated references, the latest version (including all amendments) applies to this document. GB 9254-2008 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement ITU-R SM.1539-1 (2002) Variation of the boundary between the out-of-band and spurious domains required for the application of Recommendations ITU- R SM.1541 and ITU-R SM. 3293 Terms, definitions and abbreviations3.1 Terms and definitions The following terms and definitions apply to this document. 3.2 Abbreviations The following abbreviations apply to this document.4 Technical requirements4.1 Environmental requirements The equipment manufacturer shall declare in advance the environmental conditions under which the equipment works; the equipment shall work in its nominal working environment. 4.2 Conformity requirements 4.2.1 Peak equivalent isotropic radiated power 4.2.2 Average equivalent isotropic radiated power 4.2.2.1 Overview The product of the average power output to the antenna relative to the antenna gain of the isotropic antenna in the specified direction. 4.2.3.1 Overview The peak power output to the antenna port. 4.2.3.2 Limit When the transmitter is working at the maximum power level, the antenna port output power’s limit is 10 dBm. 4.2.4 Transmitter’s spurious emissions 4.2.4.2 Limit value The transmitter spurious limits are as shown in Table 2. 4.2.5 Receiver spurious emissions 4.2.5.1 Overview Receiver spurious emission refers to the unwanted emission in the spurious domain when the device is in the receiving state. 4.2.6 Carrier frequency tolerance 4.2.6.1 Overview Frequency range Transmit state limit Transmitter standby or idle state a Test bandwidth 4.2.7 Out-of-band emission 4.2.7.1 Overview The out-of-band emission in this standard specifically refers to the maximum power spectral density of the transmitter in the frequency range of 57 GHz ~ 59 GHz and 64 GHz ~ 66 GHz. 4.2.7.2 Limit value The out-of-band emission limit is. -5 dBm/MHz 4.2.8 Integrated antenna The device shall have an integrated antenna structure, to prevent users from disassembling the integrated antenna and installing antenna connectors to replace other antennas during use.5 Test method5.1 Environmental conditions of the test The test items as defined in this standard shall be carried out under normal working environmental conditions. These environmental conditions shall be within the limit operating environment stated by the manufacturer. 5.3 Test configuration 5.3.1 Product Information The device under test shall provide the following information before the start of the test. 5.3.2 Modulation method, frequency and configuration 5.3.2.1 Modulation method The test modulation used shall be representative of the normal use of the equipment. If the equipment cannot conduct continuous emission during normal use, the test shall be able to ensure. 5.3.3 Peak equivalent isotropic radiated power The peak equivalent isotropic radiated power shall be measured using the test field as described in Appendix A and the method in Appendix B. 5.3.6 Transmitter spurious emissions 5.3.6.1 Configuration requirements Transmitter's unwanted emissions shall be measured using the test field as described in Appendix A and the method in Appendix B. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of YD/T 2722-2014 be delivered?Answer: The full copy PDF of English version of YD/T 2722-2014 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of YD/T 2722-2014_English with my colleagues?Answer: Yes. The purchased PDF of YD/T 2722-2014_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- YD/T 2722-2014 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of YD/T 2722-2014?A step-by-step guide to download PDF of YD/T 2722-2014_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "YD/T 2722-2014". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
