QC/T 29106-2014 PDF EnglishUS$125.00 · In stock · Download in 9 seconds
QC/T 29106-2014: Technical Specification of Automobile Wire Harness Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid QC/T 29106: Historical versions
Similar standardsQC/T 29106-2014: Technical Specification of Automobile Wire Harness---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/QCT29106-2014ICS 43.040.10 E 36 QC Automobile Industry Standard of the People’s Republic of China Replacing QC/T 29106-2014 Technical Specification of Automobile Wire Harness Issued on. MAY 06, 2014 Implemented on. OCTOBER 1, 2014 Issued by. Ministry of Industry and Information Technology of the People's Republic of China Ministry of Industry and Information Technology of the People's Republic of China Table of ContentsForeword... 8 1 Scope... 10 2 Normative References... 10 3 Terms and Definitions... 12 4 Requirements... 13 5 Test Method... 25 6 Inspection Rules... 33 7 Marking, Packaging, Storage and Custody... 35 Annex A (Normative) Requirements for the Cross-section of Crimping Area and Crimping Juncture of Terminals and Wire Conductors... 37 Annex B (Normative) Heat-shrinkable Double-wall Tubes for Automobile Wire Harnesses... 39 Annex C (Normative) Pressure-sensitive Adhesive Tapes for Automobile Wire Harnesses... 42 Annex D (Normative) Bellows for Automobile Wire Harnesses... 441 ScopeThis Standard specifies the requirements, test methods, inspection rules, marking, packaging, storage and custody of automobile wire harnesses (hereinafter referred to as wire harnesses). This Standard applies to various automobile wire harnesses with the nominal voltage less than 60 V (including single-wire assemblies).2 Normative ReferencesThe following documents are essential to the application of this Standard. For the dated references, only the dated editions apply to this Standard. For the undated references, the latest edition (including all amendments) applies to this Standard. GB/T 2423.1-2008 Environmental Testing - Part 2.Test method - Test A. Cold GB/T 2423.2-2008 Environmental Testing - Part 2.Test method - Test B. Dry heat GB/T 2423.17-2008 Environmental Testing for Electric and Electronic Products - Part 2.Test Method - Test Ka. Salt mist GB/T 2423.22-2002 Environmental Testing for Electric and Electronic Products - Part 2.Test Method - Test N. Change of Temperature GB/T 2828.1-2012 Sampling Procedures for Inspection by Attributes – Part 1. Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-Lot Inspection GB/T 4086 Glass Cleaning Agent3 Terms and DefinitionsThose listed below and the definitions in QC/T 417.1-2001 are adopted in this Standard. 3.1 Main Stem A portion of a wire harness in which two or more wires are taped together, as shown in Figure 1. 3.2 Lateral A portion of a wire harness in which the ends of the wires are not taped or a single wire, as shown in Figure 1. 3.3 Embranchment Point The intersection of main stem and main stem or main stem and lateral center line in the wire harness, as shown in Figure 1. 3.4 Juncture The connection point of wire and wire, as shown in Figure 1. Figure 1 Diagram of Wire Harness 3.8 Clip A component mounted on a wire harness for fixing with a vehicle body or other corresponding components. 3.9 Desiccation Bound The area which requires no special waterproofing treatment because a wire harness is installed in cab, compartment, trunk or other parts.4 Requirements4.1 General Requirements 4.2 Appearance 4.2.1 The installation of wires and parts, the position of embranchment points and the embranchment direction shall meet the requirements of drawings and technical requirements. 4.2.2 The wires and parts shall be free from the defects including damage, and deformation. 4.2.3 The terminals shall not come off the protection sleeve. 4.2.4 After the terminals with seal plug for insulated crimping are installed with the protection sleeves, the seal plug shall not retreat from the protection sleeves. 4.2.7 The wire harness banded with adhesive tape, as shown in Figure 3 and Figure 4, shall meet the following requirements. 4.3 Size of Wire Harness 4.3.1 The length of main stems and protection sleeves shall not be less than 50 mm. 4.4 Connection of Terminals and Wires 4.4.1 Crimp connection. The connection of terminals and the wires shall give priority to the crimping method shown in Figure 9. 4.8 Temperature Resistance Performance The wire harnesses shall meet the requirements of 4.2 and 4.7 after low temperature, high temperature and temperature change resistance tests according to the lower limit working temperature Tmin and upper limit working temperature Tmax provided in drawings and technical documents.5 Test Method5.1 Test Conditions Unless otherwise specified, the test sample shall be tested after stabilization for 24 h under the conditions as follows. 5.3 Dimensional Inspection 5.3.1 Use a steel tap to measure the basic dimensions of wire harnesses and the dimensions of taping. 5.3.2 Use a special gauge or protractor to measure the direction of wire harness branching and the direction of clips. 5.4 Test of Terminal and Wire Connection 5.4.1 Take visual inspection for a), b), c) and d) in 4.4.2 Conductor crimping and 4.4.4 and 4.4.8. 5.4.5 Connection strength test. Conductor crimp Cut-off position Wire Cut-off position. It shall not be close to the location of front and back R; it shall be close to the middle position of the crimping area while avoiding the interior reinforcing bar of terminals. 5.5.4 Water immersion test of damp bound juncture. 5.5.6 Crimping juncture cross-section. implement in accordance with 5.4.4. 5.6 Waterproof Performance Test of Rubber Parts 5.6.1 Test facility. partition board, φ16 mm spray water hose, high pressure water pump, water pressure regulator and chronograph. 5.6.2 Test sample. take samples from actual products; the samples shall be 100 mm at least longer than the waterproof portion of rubber parts.7 Marking, Packaging, Storage and Custody7.1 Marking 7.1.1 The wire harnesses shall be provided with a distinctive mark which is not easily detached. 7.1.2 When it is not required by drawings and technical documents, the product marking shall include the items as follows. 7.2 Packaging Packing documents. 7.3 Storage and Custody The storage and storage of the product shall meet the relevant requirements of QC/T 238.The shelf life of the product is normally 2 years. The product shall continue to meet the mentioned requirements of this standard after 2 years' shelf life. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of QC/T 29106-2014 be delivered?Answer: The full copy PDF of English version of QC/T 29106-2014 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of QC/T 29106-2014_English with my colleagues?Answer: Yes. The purchased PDF of QC/T 29106-2014_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- QC/T 29106-2014 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version QC/T 29106-2014?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version QC/T 29106-2014 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of QC/T 29106-2014?A step-by-step guide to download PDF of QC/T 29106-2014_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "QC/T 29106-2014". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
