QB/T 2280-2016 PDF EnglishUS$145.00 · In stock · Download in 9 seconds
QB/T 2280-2016: Office furniture. Office chair Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid QB/T 2280: Historical versions
Similar standardsQB/T 2280-2016: Office furniture. Office chair---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/QBT2280-2016QB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 97.140 Y 81 Record Number. 53766-2016 Replacing QB/T 2280-2007 Office Furniture-Office Chair Issued on. JANUARY 15, 2016 Implemented on. JULY 1, 2016 Issued by. Ministry of Industry and Information Technology of the People's Republic of China Table of ContentsForeword... 3 1 Scope... 5 2 Normative References... 5 3 Terminologies and Definitions... 6 4 Product Classification... 8 5 Requirements... 9 6 Test Methods... 17 7 Inspection Rules... 37 8 Marking, Packaging, Transportation and Storage... 39 Appendix A (Normative) 64kg Load Module... 41 Appendix B (Normative) Impact Bag... 421 ScopeThis standard specifies the terminologies and definitions, product classification, requirements, test methods, inspection rules and marking, packaging, transportation and storage of office chairs. This standard is applicable to office chairs; chairs of similar uses in other occasions may refer to this standard.2 Normative ReferencesThe following documents for the application of this document are essential. Any dated reference, just dated edition applies to this document. For undated references, the latest edition (including any amendments) applies to this document. GB/T 2828.1 Sampling Procedures for Inspection by Attributes - Part 1. Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection GB/T 3325-2008 Metal Furniture - General Technical Requirements GB/T 3920 Textiles - Tests for Colour Fastness - Colour Fastness to Rubbing GB 5296.6 Instructions for Use of Products of Consumer Interest - Part 6. Furniture GB/T 6343 Cellular Plastics and Rubbers - Determination of Apparent Density GB/T 6669-2008 Flexible Cellular Polymeric Materials - Determination of Compression Set GB/T 6670-2008 Flexible Cellular Polymeric Materials - Determination of Resilience by Ball Rebound GB/T 9286 Paints and Varnishes - Cross Cut Test for Films GB/T 10357.2 Test of Mechanical Properties of Furniture - Part 2.Stability of Chairs and Stools GB/T 10357.3-2013 Test of Mechanical Properties of Furniture - Part 3.Strength and Durability of Chairs and Stools GB 17927.1 Upholstered Furniture - Assessment of the Resistance to Ignition of Mattress and Sofa - Part 1.Smouldering Cigarette GB 17927.2 Upholstered Furniture - Assessment of the Resistance to Ignition of Mattress and Sofa - Part 2.Match Flame Equivalent GB/T 18204.2-2014 Examination Methods for Public Places - Part 2.Chemical Pollutants3 Terminologies and DefinitionsFor the purposes of this standard, the terminologies and definitions established in GB/T 29525-2013 and the following ones apply. 3.1 Office chair An individual chair used when doing office work. 3.2 Adjuster device Mechanism changing the relative position, angle or rigidity of seat parts. 3.3 Locking device Device which makes moving parts of chair in position and locks them up. 3.4 Shape symmetry Extent of the error in symmetry planes where chair parts are located, diagonals or circle diameter. 3.5 Seat plane deviation The extent of the plane where the bilaterally symmetric points at seat's hard edge tilts to the ground level. 3.6 Back eccentric Distance between a vertical line through forced points at back top and a line through support points at outermost side of base.4 Product ClassificationOffice chairs are classified into the following types by adjustment mode.5 Requirements5.1 Main dimensions Main product dimensions shall be in accordance with those specified in Table 1.See Figures 4, 5 and 6 and Table 1 for codes and deviation requirements. The dimensions with special requirements shall be indicated by the supplier and the purchaser in the contract. 5.2 Shape and position tolerances Product shape and position tolerances shall be in accordance with those specified in Table 2. 5.3 Appearance 5.3.1 Appearance of plastic parts 5.3.5 Coating and plating 5.3.5.1 Wooden parts coating shall be flat and smooth without scratch, fog lights, white ridge, flake, sagging, deposited powder, lag or visible color difference.* 5.3.5.2 Wooden parts coating shall be free from swelling, wrinkling, sticking and holiday. 5.3.6 Other appearance requirements 5.3.6.1 The parts of the product shall be free from damage. 5.3.6.2 Fixed positions shall be joined firmly without looseness, lack of parts, nail missing or exposure. 5.3.6.3 All the external angles of the product and positions in contact with human body shall be blunted without burr, cutting edge or corner angle. 5.4 Physical and chemical properties Physical and chemical properties of the product shall meet those specified in Table 3. Table 3 -- Physical and Chemical Properties 5.5 Mechanical properties Mechanical properties of the product shall meet those specified in Table 4. 5.8 TVOC TVOC of office chair shall not be greater than 0.5 mg/m2h. 5.9 Safety (only applicable to office chair with gas spring) 5.9.1 Basic safety Isolation measures shall be taken between the bottom of the seat and the gas spring, steel plate or chassis not less than 2 mm in thickness may be adopted for isolation.6 Test Methods6.1 Precision Unless otherwise specified, the following measuring precision shall be adopted. 6.2 Main dimensions 6.2.1 Determination of Point A Put a 64 kg-load module (see Appendix A) on the seat with center line as symmetry plane, ensuring that the center of guiding axle of the main weight is consistent with the center of the seat's rotation axle. Before the test, the seat shall be loaded before being unloaded, repeat 5 times. 6.2.3 Seat height As shown in Figure 8, put the seat on a flat and hard plate, determine Point A with a 64 kg-load module (see Appendix A), measure the distance from Point A to the plate H1 (see Figure 8). 6.2.4 Lift travel Measure the highest seat height and the lowest seat height in accordance with 6.2.3, and calculate the difference. 6.2.5 Other main dimensions Other main dimensions shall be determined according to the requirements of 5.1 in GB/T 3325-2008. 6.3 Shape and position tolerances 6.3.1 Back eccentricity Rotate the test piece to where it is easiest to overturn, measure the horizontal distance e between the connecting line of support points at the outermost side of the base and vertical lead of the force bearing point, d, at the top of the back. 6.3.2 Shape symmetry Measure the distance between two diagonals of the symmetry plane (component), then measure the distance between support points of support castor for the base, and the difference between them is the shape symmetry. 6.4 Appearance 6.4.1 Decoloration Inspect 3 positions on the product's external finished parts or plastic parts, wipe each position with white soft damp cloth or white degreased gauze properly for 3 times for a distance of 200 mm ~300 mm. Observe if the soft damp cloth or white degreased gauze has the color of the finished parts. 6.5 Physical and chemical properties 6.5.1 Flexible polyurethane foam 6.5.2 Color fastness to dry friction of textile fabric It shall be tested according to the requirements of GB/T 3920. 6.5.3 Metal parts coating 6.5.3.1 Resistance to salt spray It shall be tested according to the requirements of QB/T 3826. 6.5.3.2 Adhesive force It shall be tested according to the requirements of GB/T 9286. 6.5.4 Resistance to salt spray of galvanized coating It shall be tested according to the requirements of QB/T 3826. 6.6 Mechanical property 6.6.1 Stability It shall be tested according to the requirements of GB/T 10357.2. 6.6.3 Static load on seat and back 6.6.3.1 Static load on seat It shall be tested according to the requirements of 4.3.1 in GB 10357.3-2013. 6.6.3.2 Static load on back It shall be tested according to the requirements of 4.3.2 in GB 10357.3-2013. 6.6.6 Reciprocating abrasion on castor Connect the chair and the circulating equipment together. Put the chair on a hard and smooth surface with 3 obstacles (see Figure 14), as shown in Figure 15. 6.6.7 Static load on base As shown in Figure 17, put inside steel block or other similar supporting objects instead of roller / sliding feet (roller / sliding toe pool may be kept). The axis of roller / sliding feet provides support. The height of the steel block or supporting object shall be enough for the central axis or chair leg not to touch the test bed in the test process. Remove the support device and height adjusting device on the base. Directly load on the support bar in a vertical way, or apply load vertically by conical test device or the test device similar to base interface. 6.10 Safety 6.10.1 Basic safety The steel plate thickness shall be measured by straight steel ruler or tape with division value of 1mm. 6.10.2 Sealing performance Remove the parts above the seat of the sample. Keep the gas spring compressed, then measure the seat height according to 6.2.3; and measure the seat height again according to 6.2.3 after storing for 72 h at normal temperature. 6.10.3 High and low temperature resistance The prepared sample shall be subjected to high/low temperature treatment. firstly, put it into a (-30±2)℃ low temperature test chamber for 48h, take it out, then put it into a (60±5)℃ high temperature test chamber for another 48h. Take out the gas spring and calculate the decrement of its nominal force Fa. 6.10.4 Cycle life The gas spring piston rod undergone high/low temperature storage test shall be clamped on the testing machine downward for cycling life test at the frequency of 8 times / min - 12 times / min, and the temperature of the wall of outer drum shall not be larger than 50℃ during the test. After cycling for 50,000 times, measure the decrement of nominal force Fa.7 Inspection Rules7.1 Inspection classification Product inspection may be classified into type inspection and end-of-manufacturing inspection. Type inspection evaluates the compliance of all inspection items in addition to those specified in the contract. While end-of-manufacturing inspection judges the compliance of the items specified in 5.1, 5.2 and 5.4 of this standard. 7.2 End-of-manufacturing inspection 7.2.1 End-of-manufacturing inspection shall be carried out at the end of manufacturing of the product or in case of delivery. The items specified in 5.1, 5.2 and 5.3 of this standard are end-of-manufacturing inspection items. 7.2.3 End-of-manufacturing inspection shall be carried out by the quality inspection department of the enterprise within the validity of the type inspection of product. 7.2.4 All the inspection items without "*" in main dimension, tolerances of form and position and appearance are qualified; while those with "*" and with no more than 5 defects are judged as qualified in the end-of-manufacturing inspection, otherwise they shall be judged as unqualified. 7.2.5 Unqualified products shall not leave the factory. 7.3 Type inspection 7.3.1 Type inspection is about comprehensive assessment on product quality. Type inspection shall be carried out under one of the following conditions. 7.3.2 Sampling and product grouping rules In sampling, 7 samples, 1 component base, 1 gas spring and a set of castor shall be randomly taken from the same batch within an inspection period, except that 3 samples shall be sealed for storing, the rest shall be delivered for inspection. If the supplier and the purchaser have other contract provisions, then samples shall be taken according to those specified in the Contract. 7.3.5 Reinspection 7.3.5.1 Re-inspection may be carried out in case either party has disagreement on the inspection results during inspection and to the objectionable items of un-accepted products within the specified period during delivery. 7.3.5.2 Re-inspection shall be directly carried out to stand-by samples. 7.3.5.3 The items unqualified last time or failing to be inspected last time due to damage of sample shall be subjected to re-inspection and noted with "re-inspected" in the report.8 Marking, Packaging, Transportation and Storage8.1 Marking The products shall be provided with marking and application instruction, and shall meet the requirements of GB 5296.6.The contents of product instructions shall at least include. 8.2 Packaging The product shall be appropriately packaged to avoid damage. 8.3 Transportation The products shall be provided with gasket and cover during transportation to avoid damage, sun and rain. 8.4 Storage The products shall be stored in the well-ventilated, dry and clean environment to avoid contamination, sun and rain. QB/T 2280-2016 QB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 97.140 Y 81 Record Number. 53766-2016 Replacing QB/T 2280-2007 Office Furniture-Office Chair Issued on. JANUARY 15, 2016 Implemented on. JULY 1, 2016 Issued by. Ministry of Industry and Information Technology of the People's Republic of ChinaTable of ContentsForeword... 3 1 Scope... 5 2 Normative References... 5 3 Terminologies and Definitions... 6 4 Product Classification... 8 5 Requirements... 9 6 Test Methods... 17 7 Inspection Rules... 37 8 Marking, Packaging, Transportation and Storage... 39 Appendix A (Normative) 64kg Load Module... 41 Appendix B (Normative) Impact Bag... 421 ScopeThis standard specifies the terminologies and definitions, product classification, requirements, test methods, inspection rules and marking, packaging, transportation and storage of office chairs. This standard is applicable to office chairs; chairs of similar uses in other occasions may refer to this standard.2 Normative ReferencesThe following documents for the application of this document are essential. Any dated reference, just dated edition applies to this document. For undated references, the latest edition (including any amendments) applies to this document. GB/T 2828.1 Sampling Procedures for Inspection by Attributes - Part 1. Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection GB/T 3325-2008 Metal Furniture - General Technical Requirements GB/T 3920 Textiles - Tests for Colour Fastness - Colour Fastness to Rubbing GB 5296.6 Instructions for Use of Products of Consumer Interest - Part 6. Furniture GB/T 6343 Cellular Plastics and Rubbers - Determination of Apparent Density GB/T 6669-2008 Flexible Cellular Polymeric Materials - Determination of Compression Set GB/T 6670-2008 Flexible Cellular Polymeric Materials - Determination of Resilience by Ball Rebound GB/T 9286 Paints and Varnishes - Cross Cut Test for Films GB/T 10357.2 Test of Mechanical Properties of Furniture - Part 2.Stability of Chairs and Stools GB/T 10357.3-2013 Test of Mechanical Properties of Furniture - Part 3.Strength and Durability of Chairs and Stools GB 17927.1 Upholstered Furniture - Assessment of the Resistance to Ignition of Mattress and Sofa - Part 1.Smouldering Cigarette GB 17927.2 Upholstered Furniture - Assessment of the Resistance to Ignition of Mattress and Sofa - Part 2.Match Flame Equivalent GB/T 18204.2-2014 Examination Methods for Public Places - Part 2.Chemical Pollutants3 Terminologies and DefinitionsFor the purposes of this standard, the terminologies and definitions established in GB/T 29525-2013 and the following ones apply. 3.1 Office chair An individual chair used when doing office work. 3.2 Adjuster device Mechanism changing the relative position, angle or rigidity of seat parts. 3.3 Locking device Device which makes moving parts of chair in position and locks them up. 3.4 Shape symmetry Extent of the error in symmetry planes where chair parts are located, diagonals or circle diameter. 3.5 Seat plane deviation The extent of the plane where the bilaterally symmetric points at seat's hard edge tilts to the ground level. 3.6 Back eccentric Distance between a vertical line through forced points at back top and a line through support points at outermost side of base.4 Product ClassificationOffice chairs are classified into the following types by adjustment mode.5 Requirements5.1 Main dimensions Main product dimensions shall be in accordance with those specified in Table 1.See Figures 4, 5 and 6 and Table 1 for codes and deviation requirements. The dimensions with special requirements shall be indicated by the supplier and the purchaser in the contract. 5.2 Shape and position tolerances Product shape and position tolerances shall be in accordance with those specified in Table 2. 5.3 Appearance 5.3.1 Appearance of plastic parts 5.3.5 Coating and plating 5.3.5.1 Wooden parts coating shall be flat and smooth without scratch, fog lights, white ridge, flake, sagging, deposited powder, lag or visible color difference.* 5.3.5.2 Wooden parts coating shall be free from swelling, wrinkling, sticking and holiday. 5.3.6 Other appearance requirements 5.3.6.1 The parts of the product shall be free from damage. 5.3.6.2 Fixed positions shall be joined firmly without looseness, lack of parts, nail missing or exposure. 5.3.6.3 All the external angles of the product and positions in contact with human body shall be blunted without burr, cutting edge or corner angle. 5.4 Physical and chemical properties Physical and chemical properties of the product shall meet those specified in Table 3. Table 3 -- Physical and Chemical Properties 5.5 Mechanical properties Mechanical properties of the product shall meet those specified in Table 4. 5.8 TVOC TVOC of office chair shall not be greater than 0.5 mg/m2h. 5.9 Safety (only applicable to office chair with gas spring) 5.9.1 Basic safety Isolation measures shall be taken between the bottom of the seat and the gas spring, steel plate or chassis not less than 2 mm in thickness may be adopted for isolation.6 Test Methods6.1 Precision Unless otherwise specified, the following measuring precision shall be adopted. 6.2 Main dimensions 6.2.1 Determination of Point A Put a 64 kg-load module (see Appendix A) on the seat with center line as symmetry plane, ensuring that the center of guiding axle of the main weight is consistent with the center of the seat's rotation axle. Before the test, the seat shall be loaded before being unloaded, repeat 5 times. 6.2.3 Seat height As shown in Figure 8, put the seat on a flat and hard plate, determine Point A with a 64 kg-load module (see Appendix A), measure the distance from Point A to the plate H1 (see Figure 8). 6.2.4 Lift travel Measure the highest seat height and the lowest seat height in accordance with 6.2.3, and calculate the difference. 6.2.5 Other main dimensions Other main dimensions shall be determined according to the requirements of 5.1 in GB/T 3325-2008. 6.3 Shape and position tolerances 6.3.1 Back eccentricity Rotate the test piece to where it is easiest to overturn, measure the horizontal distance e between the connecting line of support points at the outermost side of the base and vertical lead of the force bearing point, d, at the top of the back. 6.3.2 Shape symmetry Measure the distance between two diagonals of the symmetry plane (component), then measure the distance between support points of support castor for the base, and the difference between them is the shape symmetry. 6.4 Appearance 6.4.1 Decoloration Inspect 3 positions on the product's external finished parts or plastic parts, wipe each position with white soft damp cloth or white degreased gauze properly for 3 times for a distance of 200 mm ~300 mm. Observe if the soft damp cloth or white degreased gauze has the color of the finished parts. 6.5 Physical and chemical properties 6.5.1 Flexible polyurethane foam 6.5.2 Color fastness to dry friction of textile fabric It shall be tested according to the requirements of GB/T 3920. 6.5.3 Metal parts coating 6.5.3.1 Resistance to salt spray It shall be tested according to the requirements of QB/T 3826. 6.5.3.2 Adhesive force It shall be tested according to the requirements of GB/T 9286. 6.5.4 Resistance to salt spray of galvanized coating It shall be tested according to the requirements of QB/T 3826. 6.6 Mechanical property 6.6.1 Stability It shall be tested according to the requirements of GB/T 10357.2. 6.6.3 Static load on seat and back 6.6.3.1 Static load on seat It shall be tested according to the requirements of 4.3.1 in GB 10357.3-2013. 6.6.3.2 Static load on back It shall be tested according to the requirements of 4.3.2 in GB 10357.3-2013. 6.6.6 Reciprocating abrasion on castor Connect the chair and the circulating equipment together. Put the chair on a hard and smooth surface with 3 obstacles (see Figure 14), as shown in Figure 15. 6.6.7 Static load on base As shown in Figure 17, put inside steel block or other similar supporting objects instead of roller / sliding feet (roller / sliding toe pool may be kept). The axis of roller / sliding feet provides support. The height of the steel block or supporting object shall be enough for the central axis or chair leg not to touch the test bed in the test process. Remove the support device and height adjusting device on the base. Directly load on the support bar in a vertical way, or apply load vertically by conical test device or the test device similar to base interface. 6.10 Safety 6.10.1 Basic safety The steel plate thickness shall be measured by straight steel ruler or tape with division value of 1mm. 6.10.2 Sealing performance Remove the parts above the seat of the sample. Keep the gas spring compressed, then measure the seat height according to 6.2.3; and measure the seat height again according to 6.2.3 after storing for 72 h at normal temperature. 6.10.3 High and low temperature resistance The prepared sample shall be subjected to high/low temperature treatment. firstly, put it into a (-30±2)℃ low temperature test chamber for 48h, take it out, then put it into a (60±5)℃ high temperature test chamber for another 48h. Take out the gas spring and calculate the decrement of its nominal force Fa. 6.10.4 Cycle life The gas spring piston rod undergone high/low temperature storage test shall be clamped on the testing machine downward for cycling life test at the frequency of 8 times / min - 12 times / min, and the temperature of the wall of outer drum shall not be larger than 50℃ during the test. After cycling for 50,000 times, measure the decrement of nominal force Fa.7 Inspection Rules7.1 Inspection classification Product inspection may be classified into type inspection and end-of-manufacturing inspection. Type inspection evaluates the compliance of all inspection items in addition to those specified in the contract. While end-of-manufacturing inspection judges the compliance of the items specified in 5.1, 5.2 and 5.4 of this standard. 7.2 End-of-manufacturing inspection 7.2.1 End-of-manufacturing inspection shall be carried out at the end of manufacturing of the product or in case of delivery. The items specified in 5.1, 5.2 and 5.3 of this standard are end-of-manufacturing inspection items. 7.2.3 End-of-manufacturing inspection shall be carried out by the quality inspection department of the enterprise within the validity of the type inspection of product. 7.2.4 All the inspection items without "*" in main dimension, tolerances of form and position and appearance are qualified; while those with "*" and with no more than 5 defects are judged as qualified in the end-of-manufacturing inspection, otherwise they shall be judged as unqualified. 7.2.5 Unqualified products shall not leave the factory. 7.3 Type inspection 7.3.1 Type inspection is about comprehensive assessment on product quality. Type inspection shall be carried out under one of the following conditions. 7.3.2 Sampling and product grouping rules In sampling, 7 samples, 1 component base, 1 gas spring and a set of castor shall be randomly taken from the same batch within an inspection period, except that 3 samples shall be sealed for storing, the rest shall be delivered for inspection. If the supplier and the purchaser have other contract provisions, then samples shall be taken according to those specified in the Contract. 7.3.5 Reinspection 7.3.5.1 Re-inspection may be carried out in case either party has disagreement on the inspection results during inspection and to the objectionable items of un-accepted products within the specified period during delivery. 7.3.5.2 Re-inspection shall be directly carried out to stand-by samples. 7.3.5.3 The items unqualified last time or failing to be inspected last time due to damage of sample shall be subjected to re-inspection and noted with "re-inspected" in the report.8 Marking, Packaging, Transportation and Storage8.1 Marking The products shall be provided with marking and application instruction, and shall meet the requirements of GB 5296.6.The contents of product instructions shall at least include. 8.2 Packaging The product shall be appropriately packaged to avoid damage. 8.3 Transportation The products shall be provided with gasket and cover during transportation to avoid damage, sun and rain. 8.4 Storage The products shall be stored in the well-ventilated, dry and clean environment to avoid contamination, sun and rain. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of QB/T 2280-2016 be delivered?Answer: The full copy PDF of English version of QB/T 2280-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of QB/T 2280-2016_English with my colleagues?Answer: Yes. The purchased PDF of QB/T 2280-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- QB/T 2280-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version QB/T 2280-2016?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version QB/T 2280-2016 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of QB/T 2280-2016?A step-by-step guide to download PDF of QB/T 2280-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "QB/T 2280-2016". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
