GB/T 9573-2013 PDF EnglishUS$125.00 · In stock · Download in 9 seconds
GB/T 9573-2013: Rubber and plastics hoses and hose assemblies -- Methods of measurement of the dimensions of hoses and the lengths of hose assemblies Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 9573: Historical versions
Similar standardsGB/T 9573-2013: Rubber and plastics hoses and hose assemblies -- Methods of measurement of the dimensions of hoses and the lengths of hose assemblies---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT9573-2013 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 23.040.70 G 42 GB/T 9573-2013 / ISO 4671:2007 Replacing GB/T 9573-2003 Rubber or plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671:2007, IDT) ISSUED ON: JULY 19, 2013 IMPLEMENTED ON: DECEMBER 01, 2013 Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. GB/T 9573-2013 Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Test piece conditioning and measurement temperature ... 5 4 Measurement of inner-diameter ... 6 5 Measurement of outer-diameter ... 7 6 Measurement of diameter over reinforcement ... 8 7 Measurement of wall thickness ... 9 8 Measurement of concentricity ... 10 9 Measurement of lining and cover thickness ... 11 10 Measurement of length and identification of measurement point ... 13 11 Verification of through-bore of hose assemblies ... 16 12 Test report ... 16 Bibliography ... 18 GB/T 9573-2013ForewordThis Standard is drafted according to the rules given in the GB/T 1.1-2009. This Standard replaces GB/T 9573-2003 “Rubber or plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies”. Compared with GB/T 9573-2003, the main changes of this Standard are as follows: - ADD test piece conditioning and measurement temperature (see Chapter 3); - ADD method of using tapered gauges to measure inner-diameter (see 4.2); - ADD measuring method of inner-diameter (see 4.8); - ADD measuring method of outer-diameter (see 5.6); - ADD the readings parts of measuring methods for different wall thicknesses (see 7.1); - ADD the readings parts of measuring methods for concentricity (see 8.1); - ADD three methods of measuring concentricity (see 8.4, 8.5, 8.6); - REVISE the measuring methods for the thickness of the lining and cover (see 9.2; Chapter 8 in 2003 edition); - REVISE verification of through-bore of hose assemblies (see Chapter 11; Chapter 10 in 2003 edition). This Standard uses translation method and equivalently adopts ISO 4671:2007 “Rubber or plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies” (English edition). The editorial amendments in this Standard are as follows: - ISO 3611 “Micrometer callipers for observation and measurement” in the Chapter 2 normative references of ISO 4671:2007 is deleted because it is not cited in main text. This Standard was proposed by China Petroleum and Chemical Industry Federation. This Standard shall be under the jurisdiction of National Technical Committee on Rubber and Products of Standardization Administration of China (SAC/TC 35/SC 1). Drafting organizations of this Standard: Shandong Mei Chen Technology Co., Ltd., Shenyang Rubber Research & Design Institute, and Shenyang Institute of Product GB/T 9573-2013 Rubber or plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies1 ScopeThis Standard specifies methods of measuring the inner-diameter, outer-diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity and lining and cover thickness of hoses, methods of measurement and identification of the lengths of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies.2 Normative referencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this document. ISO 463 Geometrical Product Specifications (GPS) - Dimensional measuring equipment design and metrological characteristics of mechanical dial gauges ISO 3599 Vernier calipers reading to 0.1 and 0.05 mm3 Test piece conditioning and measurementtemperature 3.1 Conditioning of test pieces Unless otherwise specified, test pieces shall be taken at least 16 h after manufacture of the hose and conditioned at 173-23 °C for at least 3 h before measurement. This 3 h can be included in the 16 h. 3.2 Measurement temperature Unless otherwise specified, the measurement temperature shall be 173-23 °C. GB/T 9573-2013 4.4 Method 3 For all inner-diameters up to and including 100 mm, the internal jaws of vernier slide callipers complying with the requirements of ISO 3599 may be used. Make two measurements at right angles to each other and take their average as the inner-diameter. Take care not to distort the hose when making the measurements. Callipers of suitable size may be used for nominal bores above 100 when greater accuracy than is obtainable by Method 5 (see 4.6) is required. 4.5 Method 4 For all inner-diameters, an internal calliper dial gauge (see ISO 463) with rounded feet designed for use in bores made of elastomeric material may be used, a calliper size being chosen which is suitable for the inner-diameter to be measured. Make two measurements at right angles to each other and take their average as the inner-diameter. 4.6 Method 5 For inner-diameters above 100 mm, a sufficient degree of accuracy for normal purposes is obtained by the use of a graduated steel rule. Alternatively, digital callipers or a digital micrometer may be used. Make two measurements at right angles to each other and take their average as the inner-diameter. 4.7 Method 6 For suitable diameters, and where the hose cross-section has not been distorted by the cutting operation, an optical magnifier with a scale graduated in 0.1 mm divisions may be used. Make two measurements at right angles to each other and take their average as the inner-diameter. 4.8 Method 7 For inner-diameters above 300 mm, a sufficient degree of accuracy for normal purposes is obtained by measuring the inner circumference of the hose with a measuring tape. The inner-diameter is obtained by dividing the measured value by pi (π). A measuring tape graduated in centimetres may be used.5 Measurement of outer-diameter5.1 General Measurements made by methods 1 to 5 may be made either on a full length of hose or on a test piece (minimum length 150 mm) cut from a full length. Measurements shall be made at a minimum distance of 25 mm from the ends of the hose [Translator’s reminder: In ISO 4671:2007/Amd.1:2011(E), this sentence was modified as “Measurements shall be made at a minimum distance of 25 mm from the ends of the hose in methods 1, 2, 3 and 5 and at the end of the hose in method 4”. However, ISO ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 9573-2013 be delivered?Answer: The full copy PDF of English version of GB/T 9573-2013 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 9573-2013_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 9573-2013_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 9573-2013 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 9573-2013?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 9573-2013 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 9573-2013?A step-by-step guide to download PDF of GB/T 9573-2013_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 9573-2013". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
