GB/T 8170-2008 PDF EnglishUS$75.00 · In stock · Download in 9 seconds
GB/T 8170-2008: Rules of rounding off for numerical values and expression and judgement of limiting values Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 8170: Historical versions
Similar standardsGB/T 8170-2008: Rules of rounding off for numerical values and expression and judgement of limiting values---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT8170-2008 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 03.120.30 A 41 Replacing GB/T 1250-1989, GB/T 8170-1987 Rules of rounding off for numerical values & expression and judgement of limiting values Issued on. JULY 16, 2008 Implemented on. JANUARY 01, 2009 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Terms and definitions... 5 3 Rules of rounding off for numerical values... 6 4 Expression and judgment of limiting value... 9 Bibliography... 151 ScopeThis Standard specifies the rules for rounding off values, the expression and determination of numerical limits, relevant terms and their symbols, and the method for comparing measured values or their calculated values with the limiting values specified in the standard. This Standard applies to various values obtained through testing and calculation in scientific, technological and production activities. When the obtained values need to be rounded off, they should be rounded off according to the rules given in this standard. This Standard is applicable to the preparation of various standards or other technical specifications and the determination of test results.2 Terms and definitionsFor the purposes of this Standard, the following terms and definitions apply. 2.1 rounding off for numerical values The process of omitting the last several digits of the original numerical value and then adjusting the last reserved digit to make the final obtained value approximately equal to the original numerical value. 2.2 rounding interval The minimum numerical value unit of the rounding value. 2.3 limiting values The boundary values of the index values which are presented in number, in compliance with the standard (or other technical specifications) and has to be assessed as required by the standard (or other technical specifications).3 Rules of rounding off for numerical values3.1 Determination of rounding interval 3.2 Rules of rounding off 3.2.1 The numerical value is rounded down if the leftmost one of the numbers intended to be discarded is less than 5; and the reserved numbers keep unchanged. Example. Round 12.1498 to the single digit, 12 is obtained. Round 12.1498 to one decimal place, then 12.1 is obtained. 3.2.5 When rounding off the negative number, first round its absolute value according to those specified in 3.2.1~3.2.4 and then add the negative sign at the front of the obtained value. 3.3 Continuous rounding off is not permissible 3.3.1 The rounding number shall be obtained by rounding the numerical value only once after the rounding interval or rounding digits are specified. More than one time of continuous rounding off in accordance with 3.2 is not permissible. (expressed as -0.036 in specified occasions)4 Expression and judgment of limiting value4.1 General principles for written limiting values 4.1.1 The limiting value shall be provided for the index or parameter which is presented in numbers and has to be assessed as required in the standard (or other technical specifications). 4.2 Terms expressing the limiting values 4.2.1 Basic terms 4.2.1.1 The basic terms and symbols expressing the limiting values is detailed in Table 1. 4.2.1.2 The basic terms may be used by combination to indicate the scope of limiting value. 4.2.2 Values with limit deviations 4.2.2.1 Basic value A with upper deviation +b1 of absolute limit and lower deviation - b2 of absolute limit refers to the values fromA-b2 to A+b1 meet the requirements and it is expressed as. 4.3 Comparison method of the measured value or its calculated value and the limiting value specified in the standard 4.3.1 General provisions 4.3.1.1 When judging whether the measured value or its calculated value meet the standard requirements of not, the measured value of test or its calculated value shall be compared with the limiting value specified in the standard, and any of the following methods may be adopted for comparison; 4.3.1.3 If one of comparative methods is specified in the standard or relevant document, it shall not be changed once been determined. 4.3.2 Complete numerical comparison method Do not round off the measured value or calculated value (or even though the value has been rounded off, it shall be indicated that it has been rounded down, up or neither of them) and then compare this value with specified limiting value; 4.3.3 Rounded-off-value comparison method 4.3.3.1 Round off the measured value or its calculated value, and the rounding off digit shall be consistent with the digit of the specified limiting value. 4.3.3.2 Compare the rounded off values and the specified limiting value, if this value exceeds the specified range of limiting value (no matter large or not), it will be judged as do not meet the requirements. See Table 3 for examples. Table 3 (continued) 4.3.4 Comparison of two kinds of judgment methods ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 8170-2008 be delivered?Answer: The full copy PDF of English version of GB/T 8170-2008 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 8170-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 8170-2008_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 8170-2008 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 8170-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 8170-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 8170-2008?A step-by-step guide to download PDF of GB/T 8170-2008_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 8170-2008". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
