GB/T 4893.2-2020 PDF EnglishUS$170.00 · In stock · Download in 9 seconds
GB/T 4893.2-2020: Test of surface coatings of furniture - Part 2: Determination of resistance to wet heat Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 4893.2: Historical versions
Similar standardsGB/T 4893.2-2020: Test of surface coatings of furniture - Part 2: Determination of resistance to wet heat---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT4893.2-2020 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 97.140 Y 80 Replacing GB/T 4893.2-2005 Test of surface coatings of furniture - Part 2: Determination of resistance to wet heat ISSUED ON: JULY 21, 2020 IMPLEMENTED ON: FEBRUARY 01, 2021 Issued by: State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Terms and definitions ... 5 4 Principle ... 6 5 Test conditions ... 6 6 Reagents and materials ... 6 7 Instruments and equipment... 7 8 Sample ... 8 9 Test steps ... 8 10 Test data processing ... 10 11 Test report ... 10 Bibliography ... 12 Test of surface coatings of furniture - Part 2: Determination of resistance to wet heat1 ScopeThis Part of GB/T 4893 specifies the method for determination of resistance to wet heat on furniture surface. This Part is applicable to all cured surfaces of painted furniture, and tests conducted on the surface of unused furniture or test panels. This Part is not applicable to leather and textile surfaces.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 3190, Wrought aluminium and aluminium alloys - Chemical composition limits GB/T 3505, Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters GB/T 10610, Geometrical product specifications(GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture JB/T 9262, Liquid-in-glass industrial thermometers and laboratorial thermometers JB/T 9263.4, The types and fundamental sizes of solid-stem common thermometers3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply. 3.1 test panel 6.3 Water Use deionized water or distilled water. 6.4 Insulation pad It is made of inorganic materials. The thickness is about 25mm. The size is about 150mm×150mm, or larger.7 Instruments and equipment7.1 Thermometer A thermometer that complies with JB/T 9262 and JB/T 9263.4, can be inserted into the bottom center of the heat source block (see 7.2) OR other temperature measuring equipment; the accuracy is ±1°C. 7.2 Heat source block The heat source block (see Figure 1) is made of AlMgSi (including alloy 6060 and alloy 64430) specified in GB/T 3190. The roughness Ra value of the bottom surface shall be (2±1) μm. Determine according to GB/T 3505 and GB/T 10610. The tolerances are as follows: - Length: ±0.2mm; - Angle: ±2°. 7.3 Oven An oven capable of heating the heat source block to at least 10°C higher than the test temperature. 7.4 Diffuse light source On the test area, provide uniform diffused light and reach (1200±400)lx illuminance in the test area. Diffuse natural light or diffuse artificial light can be used. NOTE: Daylight shall not be affected by surrounding trees. When using artificial daylight, it is recommended that the correlated color temperature of the light is (6500±50)K, color rendering index Ra is greater than 92 and use a colorimetric box that complies with GB/T 9761-2008 to obtain this light. accommodate the number of tests required. Between adjacent test surfaces, between the periphery of the test surface and the edge of the template, at least 15mm space shall be left. At the same time at the unfolded as the test, the periphery of the test surface shall be separated by at least 50mm. If there is any reason to believe that the performance of the test surface may change, two identical tests shall be carried out at the same time. 9.3 Before the test, use a cleaning cloth (see 6.1) to wipe the test surface gently. 9.4 Use an oven (see 7.3) to heat the heat source block (see 7.2) to at least 10°C higher than the specified test temperature. The test temperature shall be selected from the following temperatures according to the test requirements: 55°C, 70°C, 85°C, 100°C. Then transfer the heat source block to the insulation pad (see 6.4). 9.5 Insert a thermometer (see 7.1) or other temperature measuring equipment into the center hole of the heat source block. If the temperature is lower than the specified test temperature, the heat source block shall be placed in the oven again until it reaches 10°C higher than the specified test temperature. 9.6 Place the white polyamide fiber cloth (see 6.2) in the center of the test surface. Spray (2±0.2) mL of distilled water or deionized water evenly on the cloth surface (see 6.3). Make it cover the entire area of the white polyamide fiber cloth. NOTE: It is advisable to use a scaled dropper for spraying. 9.7 When the temperature of the heat source block reaches the specified test temperature ±1°C, immediately place the heat source block in the center of the white polyamide fiber cloth. 9.8 After placing for 20min, remove the heat source block. 9.9 When the test surface has cooled, use a cleaning cloth to dry the test surface. 9.10 Record the location and temperature of each test surface. 9.11 Place the test surface for 16h~24h without interference. 9.12 Use a cleaning cloth to wipe each test surface. Under the light source condition, carefully check the damage of each test surface, such as fading, tarnishing and discoloration, blistering, swelling and other defects. For this purpose, the surface is illuminated with a diffuse light source (see 7.4) from different angles, including angle combination, to reflect light from the test surface to the observer's eyes. The observation distance shall be 0.25m~1.0m. Changes caused by the test shall also be determined by touching the surface. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 4893.2-2020 be delivered?Answer: The full copy PDF of English version of GB/T 4893.2-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 4893.2-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 4893.2-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 4893.2-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 4893.2-2020?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 4893.2-2020 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 4893.2-2020?A step-by-step guide to download PDF of GB/T 4893.2-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 4893.2-2020". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |