GB/T 45711.2-2025 PDF EnglishUS$215.00 · In stock · Download in 9 seconds
GB/T 45711.2-2025: Leather - Determination of tear load - Part 2: Double edge tear Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 45711.2-2025: Leather - Determination of tear load - Part 2: Double edge tear---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT45711.2-2025GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 59.140.30 CCS Y 46 Leather - Determination of Tear Load - Part 2.Double Edge Tear (ISO 3377-2.2016, Leather - Physical and mechanical tests - Determination of tear load - Part 2.Double edge tear, MOD) Issued on: MAY 30, 2025 Implemented on: DECEMBER 1, 2025 Issued by. State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 Introduction... 4 1 Scope... 5 2 Normative References... 5 3 Terms and Definitions... 5 4 Principle... 5 5 Instruments and Equipment... 5 6 Sampling and Specimen Preparation... 7 7 Test Procedures... 7 8 Result Presentation... 8 9 Test Report... 8 Appendix A (informative) Comparison of Structural No. between This Document and ISO 3377-2.2016... 10 Appendix B (informative) Technical Differences between This Document and ISO 3377-2.2016 and the Causes... 11 Leather - Determination of Tear Load - Part 2.Double Edge Tear1 ScopeThis document describes a test method for determining the tear load of leather using the double edge tear (i.e., Baumann tear) method. This document is applicable to the determination of the tear load of various types of leather.2 Normative ReferencesThe contents of the following documents constitute indispensable clauses of this document through the normative references in the text. In terms of references with a specified date, only versions with a specified date are applicable to this document. In terms of references without a specified date, the latest version (including all the modifications) is applicable to this document. GB/T 39364 Leather - Chemical, Physical, Mechanical and Fastness Tests - Sampling Location (GB/T 39364-2020, ISO 2418.2017, MOD) GB/T 45705 Leather - Physical and Mechanical Tests - Determination of Thickness (GB/T 45705-2025, ISO 2589.2016, MOD) QB/T 2707 Leather - Physical and Mechanical Tests - Sample Preparation and Conditioning3 Terms and DefinitionsThis document does not have terms or definitions that need to be defined.4 PrinciplePlace a rectangular specimen of specified shape (with a hole in the middle) on the test hooks of the upper and lower fixtures of the tensile testing machine, operate the tensile testing machine, and record the maximum force value during the tearing process of the specimen, which is the tear load of the specimen.5 Instruments and Equipment5.1 Tensile testing machine, which complies with the following conditions. ---Tensile test range is compatible with the specimen;6 Sampling and Specimen Preparation6.1 Sampling Perform in accordance with the provisions of GB/T 39364.If sampling from a standard location is not possible (e.g., directly from shoes or clothing), specimens shall be taken from any location within the available area; the specimens shall be representative, and this shall be noted in the test report. 6.2 Specimen Preparation Use a die cutter (5.4) to cut six specimens from the grain surface (if the grain surface cannot be identified, cut from the usable surface). Three of these specimens shall have their long sides parallel to the ridgeline, and the other three specimens shall have their long sides perpendicular to the ridgeline. If the ridgeline direction cannot be identified, respectively take specimens from two mutually perpendicular directions. If more than two samples from the same batch need to be tested, at least one specimen shall be cut from each sample in each direction, with a total of no less than three specimens in each direction. 6.3 Specimen Conditioning Perform in accordance with the provisions of QB/T 2707. 6.4 Thickness Determination Perform in accordance with the provisions of GB/T 45705.The measurement location is the midpoint of the perpendicular distance between A and B and their respective side lines (short sides).7 Test Procedures7.1 Adjust the tensile testing machine, so that the hook parts of the two test hooks are close to each other. Insert the hole of the specimen into the hook parts of the two test hooks, with the wide sides of the test hooks parallel to the straight sides of the specimen hole, to ensure that the specimen is supported on the support and does not fall off. 7.2 Operate the tensile testing machine, until the specimen tears. Record the maximum force during the test. 7.3 Repeat steps 7.1 ~ 7.2 to test the remaining specimens.8 Result Presentation8.1 Tear Load The result is the arithmetic mean of the test results for each specimen in each direction, accurate to 0.1 N. If necessary (e.g., upon requested by the customer), the result may be the arithmetic mean of the test results for all specimens. 8.2 Tear Strength The tear strength of the specimen is calculated in accordance with Formula (1). Where, T---the tear strength, expressed in (N/mm); F---the tear load, expressed in (N); t---the thickness of the torn side of the specimen (if both sides are torn at the same time, take the average thickness of the two points), expressed in (mm). The result is the arithmetic mean of the test results for each specimen in each direction, accurate to 0.1 N/mm. If necessary (e.g., upon request by the customer), the result may be the arithmetic mean of the test results for all specimens.9 Test ReportThe test report shall include the following contents. a) Serial No. of this document (i.e., GB/T 45711.2); b) Detailed information about the sample and any inconsistency with GB/T 39364 in sampling; c) If necessary, the thickness of the specimen (the thickness of the torn side); d) Test results; e) Specimen conditioning and the standard atmosphere used for testing (QB/T 2707); ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 45711.2-2025 be delivered?Answer: The full copy PDF of English version of GB/T 45711.2-2025 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 45711.2-2025_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 45711.2-2025_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 45711.2-2025 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 45711.2-2025?A step-by-step guide to download PDF of GB/T 45711.2-2025_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 45711.2-2025". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
