GB/T 41875-2022 PDF EnglishUS$170.00 · In stock · Download in 9 seconds
GB/T 41875-2022: Seamless thin-wall molybdenum tubes Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 41875-2022: Seamless thin-wall molybdenum tubes---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT41875-2022GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.150.99 CCS H 63 Seamless thin-wall molybdenum tubes 无缝薄壁钼管 ISSUED ON: OCTOBER 12, 2022 IMPLEMENTED ON: MAY 1, 2023 Issued by: State Administration for Market Regulation; Standardization Administration of the PRC. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 4 4 Classification and marking ... 4 5 Technical requirements ... 5 6 Test methods ... 8 7 Inspection rules ... 8 8 Marking, packaging, transportation, storage, and accompanying documents ... 10 9 Content of order form ... 12 Seamless thin-wall molybdenum tubes1 ScopeThis document specifies the classification and marking, technical requirements, test methods, inspection rules, marking, packaging, transportation, storage, accompanying documents, and order form content of seamless thin-wall molybdenum tubes. This document is applicable to seamless thin-wall molybdenum and molybdenum-alloy tubes with a wall thickness not greater than 1.5 mm produced by pressure processing. They are mainly used as nuclear cladding tubes, heat tubes, high-temperature fuel protection tubes, draft tubes, tubular electrodes, thermocouple protection tubes, and high-temperature furnace components, etc.2 Normative referencesThe contents of the following documents, through normative references in this text, constitute indispensable provisions of this document. Among them, for dated references, only the edition corresponding to that date applies to this document. For undated references, the latest edition (including all amendments) applies to this document. GB/T 228.1 Metallic materials - Tensile testing - Part 1: Method of test at room temperature GB/T 241 Metal materials - Tube - Hydrostatic pressure test GB/T 1031 Geometrical product specifications (GPS) - Surface texture: Profile method - Surface roughness parameters and their values GB/T 4325 (all parts) Methods for chemical analysis of molybdenum3 Terms and definitionsThis document does not have terms and definitions that need to be defined.4 Classification and marking4.1 Product classification Products are divided into six categories according to chemical composition: MG-Mo, MG-MoLa, MG-MoCe, MG-MoY, MG-MoW, MG-MoRe. 5.6.3 After acid and alkali washing, the surface of the product shall have a silvery white metallic luster.6 Test methods6.1 The determination of the chemical composition of the product shall be carried out in accordance with the provisions of GB/T 4325 (all parts). The analysis methods for elements not included in GB/T 4325 (all parts) shall be determined through consultation between the supplier and the purchaser. 6.2 The dimensions of the product are measured using measuring tools with corresponding precision. 6.3 The mechanical properties of the product are determined according to the provisions of GB/T 228.1. 6.4 The hydrostatic pressure test of the product shall be carried out according to the provisions of GB/T 241. 6.5 The surface roughness of the product shall be measured according to the provisions of GB/T 1031; or determined through consultation between the supplier and the purchaser. 6.6 The appearance quality of the product shall be inspected visually.7 Inspection rules7.1 Inspection and acceptance 7.1.1 The product shall be inspected by the supplier or a third party, to ensure that the product quality complies with the provisions of this document and the order form. 7.1.2 The purchaser can inspect the received products according to the provisions of this document. If the inspection results are inconsistent with the provisions of this document and the order form, it shall be submitted to the supplier in written form; the supplier and the purchaser shall negotiate to resolve it. Objections pertaining to appearance quality shall be raised within one month from the date of receipt of the product. Objections pertaining to other performances shall be raised within three months from the date of receipt of the product. If arbitration is required, it shall be determined by consultation or sampling made jointly by both parties at the purchaser place. 7.2 Lot grouping Products shall be submitted for acceptance in lots. Each lot consists of products of the 7.5.5 If the surface roughness does not meet the requirements of this document, it is allowed to take double number of samples to repeat the test. If any result of the repeated test is nonconformity, this lot of products shall be judged as nonconformity. 7.5.6 If the appearance quality does not meet the requirements of this document, the product shall be judged as nonconformity. 8 Marking, packaging, transportation, storage, and accompanying documents 8.1 Marking 8.1.1 Product marking The following marks shall be printed on the products that have passed the inspection: a) Category; b) Status; c) Specification; d) Lot number. 8.1.2 Package marking Products shall be packed into boxes. Each box shall be marked with: a) Supplier name and trademark; b) Product name and category; c) There shall be obvious "moisture-proof" signs or words on the packaging; d) Lot number. 8.2 Packaging, transportation, and storage 8.2.1 Packaging Products shall be packaged piece by piece. The packaging materials shall be moisture- proof paper, oil-proof paper, foam paper, or other suitable materials. Place the packaged products in paper (wooden) boxes one by one; fix them with soft filling materials around them. If there are special requirements, the packaging method negotiated between the supplier and the purchaser can be used. 8.2.2 Transportation When the product is transported, moisture or acidic-alkaline gases shall be prevented. Bumping is strictly prohibited. 8.2.3 Storage The storage room shall be dry, ventilated, and free of acid and alkali. The storage period should not exceed two months. 8.3 Accompanying documents Each lot of products shall be accompanied by accompanying documents. In addition to supplier information, product information, number of this document, exit-factory date, or packaging date, it should include the following contents. a) Product quality assurance letter; the content is as follows: Main performance and technical parameters of the product; Product characteristics (including characteristics of manufacturing process and raw materials); Responsibility for product quality; Quality certification obtained by the product; various analysis and inspection results with inspection seals of the supplier's technical supervision department. b) Product conformity certificate; the content is as follows: Inspection items and their results or inspection conclusions; Lot size or lot number; Inspection date; Inspector's signature or seal. c) Inspection reports in the process of product quality control AND finished-product inspection reports. d) Product instructions: Correct handling, use, storage methods, etc. e) Other. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 41875-2022 be delivered?Answer: The full copy PDF of English version of GB/T 41875-2022 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 41875-2022_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 41875-2022_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 41875-2022 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 41875-2022?A step-by-step guide to download PDF of GB/T 41875-2022_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 41875-2022". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
