GB/T 40266-2021 PDF EnglishUS$230.00 · In stock · Download in 9 seconds
GB/T 40266-2021: Quality general rules of oxides barrier transparent plastics laminated films and pouches for food packaging Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 40266-2021: Quality general rules of oxides barrier transparent plastics laminated films and pouches for food packaging---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT40266-2021 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.140.10 G 32 Quality General Rules of Oxides Barrier Transparent Plastics Laminated Films and Pouches for Food Packaging ISSUED ON: MAY 21, 2021 IMPLEMENTED ON: DECEMBER 1, 2021 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative References ... 4 3 Terms, Definitions and Abbreviations ... 5 4 Classification and Grading ... 6 5 Requirements ... 7 6 Test Methods ... 12 7 Inspection Rules ... 16 8 Packaging, Marking, Transportation and Storage ... 19 Quality General Rules of Oxides Barrier Transparent Plastics Laminated Films and Pouches for Food Packaging1 ScopeThis Standard specifies the classification, grading, requirements, test methods, inspection rules, packaging, marking, transportation and storage of oxides barrier transparent plastics laminated films and pouches for food packaging. This Standard is applicable to AlOx coated biaxially oriented polyester film, SiOx coated biaxially oriented polyester film and SiOx coated biaxially oriented polyamide film with top and bottom coatings as the main barrier layer, as well as oxides barrier transparent plastics laminated films and pouches for food packaging made through dry lamination or solvent-free lamination. This Standard is not applicable to oxides barrier transparent plastics laminated films and pouches for food packaging without top and bottom coatings, and laminated plastic cover films for food packaging.2 Normative ReferencesThe following documents are indispensable to the application of this document. In terms of references with a specified date, only versions with a specified date are applicable to this document. In terms of references without a specified date, the latest version (including all the modifications) is applicable to this document. GB/T 191 Packaging - Pictorial Marking for Handling of Goods GB/T 1037-1988 Test Method for Water Vapor Transmission of Plastic Film and Sheet - Cup Method GB/T 1038 Plastics - Film and Sheeting - Determination of Gas Transmission - Differential-pressure Method GB/T 1040.3-2006 Plastics - Determination of Tensile Properties - Part 3: Test Conditions for Films and Sheets GB/T 2410-2008 Determination of the Luminous Transmittance and Haze of Transparent Plastics GB/T 2828.1-2012 Sampling Procedures for Inspection by Attribute - Part 1: Sampling6 Test Methods6.1 Specimen Conditioning and Standard Test Environment In accordance with the standard environment specified in GB/T 2918-2018, conduct the test. The temperature is (23 ± 2) °C and the relative humidity is (50 ± 10) %; the duration of condition is not less than 4 h. In addition, conduct the test under such conditions. 6.2 Sampling The sampling package shall be intact, and the sampling size shall be sufficient to complete the test items. During the sampling of roll film, remove the three surface layers, then, along the width direction of the roll film, conduct cutting and sampling. 6.3 Appearance Quality Under natural light, conduct visual inspection. In addition, use a measuring instrument with an accuracy of not lower than 0.5 mm for the measurement. 6.4 Quality of Printing 6.4.1 Quality of intaglio printing In accordance with the stipulations of GB/T 7707, conduct the test. 6.4.2 Quality of flexographic printing In accordance with the stipulations of GB/T 17497.2, conduct the test. 6.4.3 Quality of bar code printing In accordance with the stipulations of GB/T 18348, conduct the test on bar code. For other one-dimensional barcodes, conduct the test in accordance with the stipulations of GB/T 14258. 6.5 Dimensional Deviations 6.5.1 Deviations of length and width The deviations of length and width shall be tested in accordance with the stipulations of GB/T 6673. 6.5.2 Deviation of thickness The deviation of thickness shall be tested in accordance with the stipulations of GB/T 6672. The average deviation of thickness shall be calculated in accordance with Formula (1): Where, S---the average deviation of thickness, expressed in (%); S---the average thickness, expressed in (mm); S0---the nominal thickness, expressed in (mm). 6.5.3 Inner diameter of roll film core For the inner diameter of the roll film core, use a vernier caliper to measure three values at equal angles on the inner diameter surface of the core; take the arithmetic mean value. 6.5.4 Sealing width of pouches Use a measuring instrument with an accuracy of not lower than 0.5 mm to measure the sealing width of the pouches. 6.5.5 Distance between seal and edge Use a measuring instrument with an accuracy of not lower than 0.5 mm to measure the distance between seal and edge. 6.6 Physical and Mechanical Properties 6.6.1 Breaking force and nominal strain at break In accordance with the stipulations of GB/T 1040.3-2006, conduct the test. Adopt a long specimen, with a length of ≥ 150 mm and a width of 15 mm; the fixture spacing is (100 ± 5) mm; the tensile speed of the specimen (no-load) is (200 ± 20) mm/min. 6.6.2 Peeling force In accordance with the stipulations of Method A in GB/T 8808-1988, conduct the test. 6.6.3 Heat-sealing strength In accordance with the stipulations of QB/T 2358-1998 (2009), conduct the test. The heat-sealing conditions are: heat-sealing pressure is 0.35 MPa; heat-sealing duration is 1 s; heat-sealing temperature shall be determined by the demand-side and the supply-side through negotiation. The test direction: for the roll film type, test the longitudinal and horizontal directions; for the pouch type, test each sealed edge. 6.6.4 Oxygen transmission rate In accordance with the stipulations of GB/T 1038 or GB/T 19789, conduct the test. During the test with the differential-pressure method, the content contact surface faces the low-pressure side of oxygen or the low-concentration side of oxygen. GB/T 19789 is the arbitration method. 6.6.5 Water vapor transmission rate In accordance with the stipulations of Method A in GB/T 1037-1988 or GB/T 26253, conduct the test. During the test, the content contact surface faces the low-pressure side of water vapor or the low-concentration side of water vapor; the test temperature is (38 ± 0.6) °C and the relative humidity is (90 ± 2)%. GB/T 26253 is the arbitration method. 6.6.6 Anti-rubbing performance In accordance with Method D of ASTM F392/F392M-M(2015), conduct the test. After the film and pouch are placed still under the standard environment for 24 h, from the film and pouch, cut a 200 mm 280 mm rectangular specimen. Fix the width direction of the specimen on the fixture; start to rotate and rub it at a uniform speed; the conditions of the rubbing are as follows: a) Frequency of rubbing: 45 times/min; b) Angle of rubbing: 440°; c) Linear movement stroke: 155 mm; d) Number of rubbings: 20 times. After the rubbing is completed, horizontally flatten the specimen. The oxygen transmission rate shall be tested in accordance with the stipulations of 6.6.4; the water vapor transmission rate shall be tested in accordance with the stipulations of 6.6.5. 6.6.7 Pressure resistance of pouches 6.6.7.1 Test device See the test device of pressure resistance of the pouches in Figure 1. are disqualified items in the inspection results, double specimens shall be taken from the batch for a re-inspection of the disqualified items. If there are still disqualified items, then, it shall be determined as non-conforming to this Standard. 7.3.4 Qualification determination of batch If the batch is qualified in all the requirements of appearance quality, printing quality, and physical and mechanical properties, then, it shall be determined as conforming to this Standard. 7.4 Exit-factory Inspection Items Conduct exit-factory inspection on each batch of products. The inspection items are: appearance quality, printing quality, dimensional deviations, peeling force and heat- sealing strength. 7.5 Type Inspection Type inspection items are all items specified in Chapter 5. Except for water vapor transmission rate, oxygen transmission rate, pressure resistance of pouches, drop performance and heat resistance of pouches, which shall receive type inspection every 3 months, the type inspection shall also be conducted under one of the following circumstances: a) In the trial production and appraisal of new products; b) When there are relatively significant changes in raw materials and processes that may affect product performance; c) When the production has been suspended for more than half a year, and then, resumed; d) When there are relatively significant differences between the exit-factory inspection results and the previous type inspection; e) When it is requested by a national supervision institution; f) During normal production, it shall be carried out once a year. If all the type inspection items are qualified, the type inspection shall be determined as conforming to this Standard. If there are disqualified items in the type inspection, re- sampling is allowed for a re-inspection. After the re-inspection, if there are still disqualified items, then, the type inspection shall be determined as non-conforming to this Standard. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 40266-2021 be delivered?Answer: The full copy PDF of English version of GB/T 40266-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 40266-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 40266-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 40266-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 40266-2021?A step-by-step guide to download PDF of GB/T 40266-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 40266-2021". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
