GB/T 40126-2021 PDF EnglishUS$155.00 · In stock · Download in 9 seconds
GB/T 40126-2021: Liquid silicone rubber - Application for baby nipple Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 40126-2021: Liquid silicone rubber - Application for baby nipple---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT40126-2021GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.060 CCS G 35 Liquid silicone rubber - Application for baby nipple ISSUED ON: MAY 21, 2021 IMPLEMENTED ON: DECEMBER 01, 2021 Issued by: State Administration for Market Regulation; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 5 4 Classification and designations ... 5 5 Requirements ... 6 6 Test methods ... 6 7 Inspection rules ... 7 8 Marks, packaging, transportation, storage ... 8 Annex A (normative) Linear shrinkage test ... 10 Liquid silicone rubber - Application for baby nipple1 ScopeThis Standard specifies classification and designation, technical requirements, test methods, inspection rules, packaging, marks, transportation and storage for liquid silicone rubber for baby nipple (hereinafter referred to as silicone rubber for baby nipple). This Standard is applicable to liquid silicone rubber that is used to produce nipples and pacifiers used by infants and young children and other similar use products.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 528, Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties GB/T 529, Rubber, vulcanized -determination of tear strength (trouser, angle and crescent test pieces) GB/T 531.1, Rubber vulcanized or thermoplastic - Determination of indentation hardness - Part 1: Shore hardness tester method (Shore hardness) GB/T 533, Rubber vulcanized or thermoplastic - Determination of density GB/T 1681, Rubber - Determination of rebound GB/T 2941, Rubber - General procedures for preparing and conditioning test pieces for physical test methods GB 4806.11, National Food Safety Standard - Food Contact Rubber Materials and Articles GB/T 36804, Liquid silicone rubber - Classification and system nomenclature than 16h. 6.2.3 Hardness Determine according to GB/T 531.1. 6.2.4 Density Determine according to GB/T 533. 6.2.5 Tensile properties In accordance with GB/T 528, use type 1 specimen to determine the tensile strength and elongation at break. The number of specimens is not less than 5. 6.2.6 Tear strength Determine according to GB/T 529. Use crescent specimen. 6.2.7 Resilience Determine according to GB/T 1681. 6.2.8 Volatile compound content Determine in accordance with Annex A. 6.3 Hygienic properties Determine according to GB 4806.11.7 Inspection rules7.1 Type inspection The type inspection items are all items specified in Chapter 5. In one of the following situations, type inspection should be carried out: a) when the product is stereotyped, the production is transferred to another factory or the product is resumed after the production is stopped for more than half a year; b) when there are changes in raw materials, formulas or process conditions; c) when there is a big difference between the exit-factory inspection results and the previous type inspection; d) when it shall be carried out every six months during normal production. 7.2 Exit-factory inspection The exit-factory inspection items shall include: appearance, hardness, density, tensile strength, elongation at break, tear strength, resilience. 7.3 Batching and sampling Take the products not more than 2000kg but of the same raw materials, the same formula, and the same process as a batch. 2kg of samples are randomly selected from each batch. 7.4 Qualification judgement If the inspection items meet the requirements of Chapter 5, the batch of products is qualified. If any item of the inspection result is not in conformity, double sampling may be used to re-inspect the unqualified items. If the re- inspection result meets the requirements, the batch of products is qualified. If the re-inspection results still do not meet the requirements, the batch of products is not qualified.8 Marks, packaging, transportation, storage8.1 Marks The surface of the product or packaging shall at least indicate the following information: a) Manufacturer's name (or trademark) and address; b) Reference to this Standard; c) Product name; d) Designation; e) Batch number; f) Date of manufacture; g) Net weight or capacity. 8.2 Packaging The product is packed in clean, dry and well-sealed iron or plastic drums. Other packaging methods agreed between the manufacturer and the user can also be used. Each batch of products shall be accompanied by a product certificate, quality inspection report and product instruction manual.Annex A(normative) Linear shrinkage test A.1 Overview Dry the specimen at high temperature. Determine the content of volatile compounds by mass change. A.2 Instruments and equipment A.2.1 Oven: 200°C±5°C, ventilated. A.2.2 Desiccator. A.2.3 Balance: the accuracy is 0.1mg. A.2.4 Shallow aluminum foil box. A.2.5 Mold: 2mm thick. A.3 Specimen preparation Weigh a certain amount of unvulcanized liquid silicone rubber. Mix well according to the product manual. After vacuum deaeration, put it into the cold- mold mold. Refer to the product manual for specific curing conditions. The specimen shall be smooth and clean, uniform in thickness, and free of bubbles. The specimen size shall meet the requirements of each test performance. A.4 Test steps A.4.1 Cut the vulcanized rubber test piece into a small square with a side length of about 1cm. Weigh about 10g of specimen. Place in a desiccator (A.2.2) and park at room temperature for 48h. A.4.2 Weigh the weight of the shallow aluminum foil box (A.2.4) with a balance (A.2.3). Record as m0. Remove the specimen from the desiccator and place it in an aluminum foil box. Weigh it and record as m1. Then put it into an oven (A.2.1) at a temperature of 200°C±5°C and keep it for 4h. Take it out. Put it in a desiccator to cool for 1h. Take it out and weigh. Record as m2. A.4.3 If the test material is a paste, only need to take 10g ± 0.5g of specimen ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 40126-2021 be delivered?Answer: The full copy PDF of English version of GB/T 40126-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 40126-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 40126-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 40126-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 40126-2021?A step-by-step guide to download PDF of GB/T 40126-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 40126-2021". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
