GB/T 39381.1-2020 PDF EnglishUS$440.00 · In stock · Download in 9 seconds
GB/T 39381.1-2020: Cardiovascular implants - Vascular device-drug combination products - Part 1: General requirements Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 39381.1-2020: Cardiovascular implants - Vascular device-drug combination products - Part 1: General requirements---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT39381.1-2020 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 11.040.40 C 45 Cardiovascular Implants - Vascular Device-Drug Combination Products - Part 1: General Requirements (ISO 12417-1:2015, Cardiovascular Implants and Extracorporeal Systems – Vascular Device-Drug Combination Products – Part 1: General Requirements, MOD) ISSUED ON: NOVEMBER 19, 2020 IMPLEMENTED ON: DECEMBER 01, 2021 Issued by: State Administration for Market Regulation; Standardization Administration of PRC. Table of ContentsForeword ... 3 Introduction ... 5 1 Scope ... 6 2 Normative References ... 7 3 Terms and Definitions ... 8 4 Intended Performance ... 12 5 Design Attributes ... 13 6 Materials ... 15 7 Design Evaluation ... 15 8 Manufacturing ... 32 9 Sterilization ... 35 10 Packaging ... 36 11 Information Supplied by the Manufacturer ... 36 Annex A (Informative) Definitions of Potential Clinical and Technical Events . 40 Bibliography ... 46ForewordGB/T 39381 Cardiovascular Implants – Vascular Device-Drug Combination Products consists of the following 2 parts: --- Part 1: General Requirements; --- Part 2: Local Regulatory Guidance. This Part is Part 1 of GB/T 39381. This Part was drafted as per the rules specified in GB/T 1.1-2009. This Part uses re-drafting method to modify and adopt ISO 12417-1:2015 Cardiovascular Implants and Extracorporeal Systems – Vascular Device-Drug Combination Products – Part 1: General Requirements. Compared with ISO 12417-1:2015, the technical differences and causes of this Part are as follows: --- For the normative references, this Part adjusts according to the technical differences, so as to adapt to China’s technical conditions. The adjustment is reflected in Clause 2 “Normative References”, which are specially as follows: Use GB/T 16886.1 that equivalently adopts the international standard to replace ISO 10993-1; Use GB/T 16886.2 that equivalently adopts the international standard to replace ISO 10993-2; Use GB/T 16886.7 that equivalently adopts the international standard to replace ISO 10993-7; Use GB/T 19633.1 that equivalently adopts the international standard to replace ISO 11607-1; Use GB/T 19974 that equivalently adopts the international standard to replace ISO 14937; Use YY 0285.4 that equivalently adopts the international standard to replace ISO 10555-4; Use YY 0450.1 that equivalently adopts the international standard to replace ISO 11070; Use YY/T 0466.1 that equivalently adopts the international standard to replace ISO 15223-1; Use YY/T 0663.2 that equivalently adopts the international standard to replace ISO 25539-2. --- Add the "solvent residue" to supplement the relevant requirements for the design attributes of the drug-containing part of the device-drug combination products (see 7.2.4.3.8 of this Edition). --- Delete the "clinical evaluation" to avoid inconsistencies with Guidelines for Medical Devices Clinical Evaluation (see 7.3 of ISO12417-1:2015). This Part made the following editorial modifications: --- Modify the standard name; --- Delete the Annex B of ISO 12417-1:2015. Please note some contents of this document may involve the patents. The issuing agency of this document shall not assume the responsibility to identify these patents. This Part was proposed by National Medical Products Administration. This Part shall be under the jurisdiction of National Technical Committee for Standardization of Implants for Surgery and Orthopaedic Devices (SAC/TC 110). Drafting organizations of this Part: Tianjin Medical Device Quality Supervision and Inspection Centre; Centre for Medical Device Evaluation, NMPA; Shanghai Microport Medical (Group) Co., Ltd.; Lepu Medical Technology (Beijing) Co., Ltd.; and Medtronic (Shanghai) Management Co., Ltd. Chief drafting staffs of this Part: Duan Qingjiao, Ma Jinzhu, Zhu Lili, Cheng Maobo, Han Zheng, Zhang Xiangmei, Li Yong, Xu Jiajia, and Chen Huimin. Cardiovascular Implants – Vascular Device-Drug Combination Products – Part 1: General Requirements1 ScopeThis part of GB/T 39381 specifies the requirements for the intended performance, design attributes, materials, design evaluation, manufacturing, sterilization, packaging, and information provided by the manufacturer, etc. of the vascular device-drug combination products (VDDCPs). NOTE 1: Due to variations in the design of combination products covered by this Part and due to the relatively recent development of some of these combination products, acceptable standardized in vitro test results and clinical study results are not always available. As further scientific development and clinical data accumulation, appropriate revision of this Part might be necessary. Delivery systems or parts of the delivery system are included in the scope of this Part, if they comprise an integral component of the vascular device and if they are drug- covered (e.g.: drug-covered balloon catheters and drug-covered guidewires). This Part is also applicable to the non-permanent implantable VDDCPs. Devices whose PMOA is to provide a conduit for delivery of a drug, are excluded from the scope of this Part (e.g.: infusion catheters), unless they contain a drug component that is intended to have an ancillary action to the device part (e.g.: antimicrobial coated central venous catheter). Procedures and devices used prior to and following the introduction of the VDDCP (e.g.: balloon angioplasty devices) are excluded from the scope of this Part if they do not affect the drug-related aspects of the device. This Part includes the requirements for the absorbable components (such as coating) related to the device drug in the VDDCPs. NOTE 2: See also ISO/TS 17137. This Part does not address issues associated with viable or non-viable biological materials such as tissues, cells, or proteins. This Part does not address issues associated with active surgical implants (i.e.: implants that require power not generated by the human body or gravity).2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this document. GB/T 16886.1 Biological Evaluation of Medical Devices - Part 1: Evaluation and Testing within a Risk Management Process (GB/T 16886.1-2011, ISO 10993- 1:2009, IDT) GB/T 16886.2 Biological Evaluation of Medical Devices - Part 2: Animal Welfare Requirements (GB/T 16886.2-2011, ISO 10993-2:2006, IDT) GB/T 16886.7 Biological Evaluation of Medical Devices - Part 7: Ethylene Oxide Sterilization Residuals (GB/T 16886.7-2015, ISO 10993-7:2008, IDT) GB/T 19633.1 Packaging for Terminally Sterilized Medical Devices - Part 1: Requirements for Materials, Sterile Barrier Systems and Packaging Systems (GB/T 19633.1-2015, ISO 11607-1:2006, IDT) GB/T 19974 Sterilization of Health Care Products - General Requirement for Characterization of a Sterilization Agent and the Development, Validation and Routine Control of a Sterilization Process for Medical Devices (GB/T 19974-2018, ISO 14937:2009, IDT) YY 0285.4 Intravascular Catheters - Sterile and Single-Use Catheters - Part 4: Balloon Dilatation Catheters (YY 0285.4-2017, ISO 10555-4:2013, MOD) YY/T 0316-2016 Medical Devices - Application of Risk Management to Medical Devices (ISO 14971:2007 corrected version, IDT) YY 0450.1 Accessory Devices for Sterile Single-Use Intravascular Catheters - Part 1: Introducers (YY 0450.1-2003, ISO 11070:1998, IDT) YY/T 0466.1 Medical Devices - Symbols to be Used with Medical Device Labels, Labelling and Information to be Supplied - Part 1: General Requirements (YY/T 0466.1-2016, ISO 15223-1:2012, IDT) YY/T 0640-2016 Non-Active Surgical Implants - General Requirements (ISO 14630:2012, IDT) YY/T 0663.2 Cardiovascular Implants Endovascular Devices - Part 2: Vascular Stems (YY/T 0663.2-2016, ISO 25539-2:2012, MOD) ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 39381.1-2020 be delivered?Answer: The full copy PDF of English version of GB/T 39381.1-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 39381.1-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 39381.1-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 39381.1-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 39381.1-2020?A step-by-step guide to download PDF of GB/T 39381.1-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 39381.1-2020". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
