GB/T 39373-2020 PDF EnglishUS$165.00 · In stock · Download in 9 seconds
GB/T 39373-2020: Leather - Tests for colour fastness - Colour fastness to solvents Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 39373-2020: Leather - Tests for colour fastness - Colour fastness to solvents---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT39373-2020GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 59.140.30 Y 46 Leather - Tests for Colour Fastness - Colour Fastness to Solvents (ISO 11643:2009, Leather – Tests for Colour Fastness – Colour Fastness of Small Samples to Solvents, MOD) ISSUED ON: NOVEMBER 19, 2020 IMPLEMENTED ON: JUNE 01, 2021 Issued by: State Administration for Market Regulation; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative References ... 5 3 Principle ... 5 4 Apparatus and Materials ... 6 5 Sampling and Preparation of Specimen ... 7 6 Test Procedures ... 7 7 Representation of Results ... 8 8 Test Report ... 8 Appendix A (Informative) Clause Comparison between this Standard and ISO 11643:2009 ... 10 Appendix B (Informative) Technical Differences and the Causes between this Standard and ISO 11643:2009 ... 11 Appendix C (Informative) Method for Preparing Dry-Cleaning Solution Containing Surfactant ... 13 Leather – Tests for Colour Fastness – Colour Fastness to Solvents1 ScopeThis Standard specifies the test method for the colour fastness of leather to solvents. This Standard is applicable to the determination of the colour fastness of unused and unwashed leather to solvents. This Standard is neither applicable to leather composite materials and finished leather garments, nor does it apply to the evaluation of the dry-cleaning effect of leather garments.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this document. GB/T 250 Textiles - Tests for Colour Fastness - Grey Scale for Assessing Change in Colour (GB/T 250-2008, ISO 105-A02:1993, IDT) GB/T 251 Textiles - Tests for Colour Fastness - Grey Scale for Assessing Staining (GB/T 251-2008, ISO 105-A03:1993, IDT) GB/T 7568.7 Textiles - Tests for Colour Fastness - Standard Adjacent Fabrics - Part 7: Multifibre (GB/T 7568.7-2008, ISO 105-F10:1989, MOD) GB/T 39364 Leather - Chemical, Physical, Mechanical and Fastness Tests - Sampling Location (GB/T 39364-2020, ISO 2418:2017, MOD)3 PrincipleThe leather specimen is attached to the lining fabric, agitated in a solvent, and then remove the solvent by squeezing. After drying, the colour change of the specimen and the staining of the lining fabric are evaluated by a grey scale. petroleum solvents. If tetrachloroethylene does not affect the colour of the specimen, neither petroleum solvents shall affect it, but the reverse is not necessarily true. 4.6 Triglyceride (cis-9-octadecanoic acid ethyl ester) (also known as glyceryl trioleate), industrial grade. NOTE: The stock solution is stored in the refrigerator at 0°C~4°C, and the validity period is 1 month; the working solution is stored in the refrigerator at 0°C~4°C, and the validity period is 2 weeks. 4.7 Gray scale, including the following two types: --- Gray scale for evaluating discoloration, which shall comply with the provisions of GB/T 250; --- Gray scale for staining evaluation, which shall comply with the provisions of GB/T 251. 4.8 Heavy blocks: about 4.5kg, uniform texture, flat bottom.5 Sampling and Preparation of Specimen5.1 Sampling It shall be performed according to the provisions of GB/T 39364. 5.2 Preparation of specimen Cut a 40mm×100mm leather specimen. Fit it with a piece of about 40mm×100mm multi-fibre lining fabric (4.4), so that the flesh side (or non-wearing side) of the leather specimen is attached to the fabric. Then the formed and combined specimen is stapled at one end of the specimen, or the combined specimen may be stitched along one end of the specimen.6 Test Procedures6.1 Solvent ratio The solvent ratio shall comply with the provisions of Table 1. 6.2 Test procedures 6.2.1 Put the combined sample, (100±5) mL of solvent (6.1) and 20 PTFE rotors (4.3) into the container (4.2), and place it in the stirring device (4.1) at the speed (40±5) r/min and temperature at (30±2) °C to stir for 30min. NOTE: If necessary, before adding the specimen, it can be preheated to about 30°C by setting the temperature control device in the stirring device. 6.2.2 Take out the combined specimen; sandwich it between two absorbent papers; and place a 4.5kg weight block (4.8) on the absorbent paper and squeeze it evenly for 1min. Separate the specimen and the lining fabric; and place them in a fume hood respectively. And volatilize at room temperature to remove the residual solvent. 6.2.3 Using the untested leather specimen and the multi-fibre lining fabric (4.4) as references, the grey scale (4.7) is used to evaluate the discoloration of the specimen and the staining of the lining fabric. NOTE: After drying, the transparent tape may be used to carefully remove the fibres or loose materials adhered to the lining fabric.7 Representation of ResultsThe colour fastness to solvent of the specimen is expressed by the colour change grade of the specimen and the staining grade of the lining fabric. If necessary, any changes on the coating surface of the specimen may be recorded.8 Test ReportThe test report shall include the following: a) Number of this Standard; ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 39373-2020 be delivered?Answer: The full copy PDF of English version of GB/T 39373-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 39373-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 39373-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 39373-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 39373-2020?A step-by-step guide to download PDF of GB/T 39373-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 39373-2020". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
