GB/T 38912-2020 PDF EnglishUS$95.00 · In stock · Download in 9 seconds
GB/T 38912-2020: Test method for closed-end burst of zirconium tubes at room temperature Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 38912-2020: Test method for closed-end burst of zirconium tubes at room temperature---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT38912-2020GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.040.10 H 22 Test method for closed-end burst of zirconium tubes at room temperature ISSUED ON: JUNE 02, 2020 IMPLEMENTED ON: APRIL 01, 2021 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 4 4 Principle ... 5 5 Instruments and apparatuses ... 5 6 Sample ... 6 7 Test procedure ... 7 8 Test report ... 9 Test method for closed-end burst of zirconium tubes at room temperature1 ScopeThis Standard specifies the test method for closed-end internal pressure burst of zirconium tubes at room temperature of 10 °C ~ 35 °C. This Standard applies to the closed-end internal pressure burst test of zirconium tubes at room temperature of 10 °C ~ 35 °C, and is used for the determination of bursting strength and percent total circumferential elongation at the crevasse of zirconium tubes at room temperature.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document. GB/T 8170, Rules of rounding off for numerical values & expression and judgment of limiting values3 Terms and definitionsThe following terms and definitions are applicable to this document. 3.1 Maximum fluid pressure The maximum pressure value of the fluid acting on the end of the sample, during the entire loading process of the test. 3.2 Bursting strength The maximum stress value that is measured when the sample suddenly bursts, when the tube sample is subject to a burst test and a pressure is continuously applied through a liquid or other medium. 5.2.3 The pumping system shall be rigid, and its energy storage shall be as low as possible according to the actual situation. There shall be no pressure fluctuations in each stroke of the pump. 5.3 Valve The various valves in the testing machine shall have the functions of controlling and adjusting the pressure, and shall be able to ensure the safety of the test. 5.4 Pressure transmitter 5.4.1 The pressure transmitter shall have sufficient capacity to monitor the pressure of the system, and to ensure that the test software records the maximum fluid pressure reached during the test. 5.4.2 The measurement accuracy of the pressure transmitter shall be level-0.5 or better; the verification period shall not exceed 12 months. 5.4.3 The data collection location of the pressure transmitter shall be as close as possible to the sample. 5.5 Dimension measuring tools 5.5.1 Use an outside micrometer or other measuring tools of equivalent accuracy for the outer diameter measurement; the accuracy of the measuring tool shall not be less than 0.005 mm. 5.5.2 Use a micrometer for measuring pipe wall thicknesses or other measuring tools of equivalent accuracy for the wall thickness measurement; the accuracy of the measuring tool shall not be less than 0.005 mm. 5.5.3 Use a vernier caliper or other measuring tools of equivalent accuracy to measure the circumference after breaking; the accuracy of the measuring tool shall not be less than 0.05 mm.6 Sample6.1 General requirements 6.1.1 The sample cutting location and quantity shall be implemented in accordance with the relevant product technical requirements. The cut can be chamfered and deburred, but there shall be no deformation. 6.1.2 The sample cutting length shall be able to ensure that the unsupported length is not less than 10 times the nominal outer diameter of the sample. 6.2 Sample preparation ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 38912-2020 be delivered?Answer: The full copy PDF of English version of GB/T 38912-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 38912-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 38912-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 38912-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 38912-2020?A step-by-step guide to download PDF of GB/T 38912-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 38912-2020". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
