GB/T 38796-2020 PDF EnglishUS$110.00 · In stock · Download in 9 seconds
GB/T 38796-2020: Performance requirements and test methods of automobile blow-out emergency safety device Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 38796-2020: Performance requirements and test methods of automobile blow-out emergency safety device---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT38796-2020 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 43.040.99 T 34 Performance requirements and test methods of automobile blow-out emergency safety device ISSUED ON: JUNE 02, 2020 IMPLEMENTED ON: JUNE 01, 2021 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 5 4 Technical requirements ... 5 5 Test method ... 7 6 Same type determination ... 10 Appendix A (Normative) Performance requirements and test methods of mechanical automobile blow-out emergency safety device ... 12 Performance requirements and test methods of automobile blow-out emergency safety device1 ScopeThis Standard specifies the terms and definitions, technical requirements, test methods and the same type determination of automobile blow-out emergency safety device. This Standard applies to automobile blow-out emergency safety devices and M2, M3, N2, N3 automobiles which are installed with automobile blow-out emergency safety devices; other types of automobiles can implement by reference.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document. GB/T 2423.1-2008, Environmental testing for electric and electronic products - Part 2: Test methods - Tests A: Cold GB/T 2423.2-2008, Environmental testing for electric and electronic products - Part 2: Test methods - Tests B: Dry heat GB/T 5909-2009, Performance requirements and test methods of commercial vehicles wheels GB/T 10125-2012, Corrosion tests in artificial atmospheres - Salt spray tests GB/T 12534, Motor vehicles - General rules of road test method GB 12676, Technical requirements and testing methods for commercial vehicle and trailer braking systems GB/T 15089, Classification of power-driven vehicles and trailers GB/T 28046.3-2011, Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 4.2.4 Other requirements During the test, the automobile blow-out emergency safety device shall not have failure phenomenon such as obvious deformation, falling off, cracking and fracture.5 Test method5.1 Test conditions 5.1.1 Test equipment The installation of measuring instruments must not affect the driving safety of the vehicle. The measuring instruments and accuracy are as follows: a) Speedometer: 1%; b) Braking distance tester: 1%; c) Time measuring instrument: 1%; d) Steering wheel dynamometer: 1%. 5.1.2 Test vehicle and mass status 5.1.2.1 The technical status of the test vehicle that is equipped with an automobile blow-out emergency safety device shall meet the requirements of GB/T 12534. 5.1.2.2 The test vehicle shall be set at the maximum manufacturer's total mass status; the load shall be evenly distributed; the axle load distribution shall comply with the factory regulations. The tractor shall be tested in the train condition. 5.1.3 Test site and environment The requirements for test site and environment are as follows: a) The test road shall be a dry, hard, smooth and clean cement or asphalt road; the slope of the test road in any direction shall not exceed 2%; b) The wind speed is not more than 5 m/s; c) The temperature does not exceed 40 °C. 5.1.4 Tire blow-out simulation requirements restricted after a blow-out and cannot reach the specified speed, the corresponding test after the blow-out shall be performed at the maximum speed that the vehicle can reach. 5.2.3 Corner driving blow-out test 5.2.3.1 The test vehicle travels at a constant speed of 50 km/h ± 2 km/h along a curve with a radius of 150 m; the tire on the outer side of the simulated steering shaft blows out; after the tire blow-out, the driver immediately conducts the type-0 test of engine engagement; during the whole process, use the steering wheel dynamometer to measure the maximum steering force that is applied by the driver to the outer edge of the steering wheel during the process of maintaining a curve driving before and after the tire blow-out; calculate the maximum steering force increment before and after the tire blow-out; at the same time, record the test vehicle speed and braking distance; confirm whether the test vehicle exceeds the test track. Note: Early braking during the test may affect the overall test effect, so, the driver should avoid such situations. 5.2.3.2 For dual-steering shaft vehicles, it is available to simulate a single-sided tire blow-out only on the primary shaft. 5.2.3.3 For vehicles which are equipped with electronic control systems such as ESC or non-mechanical automobile blow-out emergency safety device, if the vehicle speed is automatically restricted after a blow-out and cannot reach the specified speed, the corresponding test after the blow-out shall be performed at the maximum speed that the vehicle can reach. 5.2.4 Steering ability test after a blow-out Before the blow-out test and after the blow-out test according to either method of 5.2.2 or 5.2.3, respectively drive the test vehicle around the pile at a speed of 50 km/h ± 2 km/h; arrange the stakes in accordance with Figure 1; measure the steering force that is applied to the outer edge of the steering wheel during the driving process; calculate the average value of the two steering force peaks when the steering wheel turns left and right before and after the tire burst-out in the effective stake area; respectively calculate the increment of average value of the front and rear steering wheels when the steering wheel turns left and right before and after the tire blow-out; the vehicle shall not knock down the stake during the test. For vehicles which are equipped with electronic control systems such as ESC or non-mechanical automobile blow-out emergency safety device, if the vehicle speed is automatically restricted after a blow-out and cannot reach the specified ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 38796-2020 be delivered?Answer: The full copy PDF of English version of GB/T 38796-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 38796-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 38796-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 38796-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 38796-2020?A step-by-step guide to download PDF of GB/T 38796-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 38796-2020". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
