GB/T 37363.2-2019 PDF EnglishUS$130.00 · In stock · Download in 9 seconds
GB/T 37363.2-2019: Determination of biocides content of coating materials - Part 2: Determination of diuron content Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 37363.2-2019: Determination of biocides content of coating materials - Part 2: Determination of diuron content---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT37363.2-2019 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 87.040 G 50 Determination of biocides content of coating materials - Part 2: Determination of diuron content ISSUED ON: MARCH 25, 2019 IMPLEMENTED ON: FEBRUARY 01, 2020 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Principle ... 5 4 Reagents or materials ... 5 5 Instruments and apparatuses ... 5 6 Sample ... 6 7 Test procedures ... 6 8 Test data processing ... 8 9 Detection-limit ... 8 10 Precision ... 8 11 Test report ... 9 Appendix A (Informative) LC-MS/MS reference conditions ... 10 Determination of biocides content of coating materials - Part 2: Determination of diuron content Caution -- The personnel who uses this Part shall have hands-on experience in formal laboratory work. This Part does not address all possible security issues. It is the responsibility of the user to take appropriate safety and health measures and to ensure compliance with the conditions which are set by the relevant national regulations.1 ScopeThis Part of GB/T 37363 stipulates the principle, reagents and materials, instruments and apparatuses, samples, test procedures, test data processing, detection-limit, precision, test report for the determination of diuron [N-(3,4- dichlorophenyl)-N', N'-Dimethylurea, CAS No: 330-54-1] by liquid chromatography-mass spectrometry/ mass spectrometry. This Part applies to the determination of diuron content in coatings. The determination of diuron content in raw materials for paint films and coatings can also refer to this Part.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document. GB/T 3186, Paints, varnishes and raw materials for paints and varnishes - Sampling GB/T 6682-2008, Water for analytical laboratory use - Specification and test methods GB/T 12806-2011, Laboratory glassware - One-mark volumetric flasks GB/T 12807-1991, Laboratory glassware - Graduated pipettes GB/T 12808-2015, Laboratory glassware - One mark pipettes Note: Other pipetting equipment, such as piston-type pipette, that meets the precision requirements, can also be used. 5.7 One mark pipette: suitable specifications, grade-A of GB/T 12808-2015. Note: Other pipetting equipment, such as piston-type pipettes, that meets the precision requirements, can also be used. 6 Sample Sampling according to the provisions of GB/T 3186, or sampling according to the agreed method; the sampling amount is determined according to the inspection needs.7 Test procedures7.1 Parallel test Perform two tests in parallel. 7.2 Sample preparation Stir the sample evenly (if the sample is solid, use a smashing device to pulverize the sample at room temperature, and use a stainless steel metal sieve (4.6) whose pore size is 0.5 mm to sieve); weigh about 2.5 g of the sample, accurate to 0.1 mg; place in a 25 mL volumetric flask (5.5); record the sample mass m; use methanol (4.1) to dilute it to the mark; shake it sufficiently to obtain the maximum dispersion of the sample; make a sample solution; record the constant volume V. Use ultrasonic extraction instrument (5.2) for ultrasonic extraction for 20 min; then, transfer about 7 mL of the above solution into a centrifuge tube (the volume of the to-be-centrifuged solution can also be adjusted according to the actual situation); centrifuge under the condition that the temperature of the centrifuge cavity does not exceed 25°C, until the supernatant A appears in the upper layer. If the centrifugation effect is not good and the layering cannot be performed effectively, increase the rotating speed or increase the centrifugation time appropriately. Use a 0.22 μm microporous membrane (4.5) to filter he supernatant A; retain the filtrate B for the determination of the extraction solution (7.7). When other solvents are selected as the extraction solvent, use a one mark pipette (5.7) to transfer 1 mL of supernatant A into a 10 mL volumetric flask (5.5); use methanol (4.1) to fix-volume to the mark. Take an appropriate amount of the above solution; use a 0.22 μm microporous membrane (4.5) to filter; retain the filtrate C for determination of the extraction solution (7.7). 7.3 Blank test Perform the blank test in parallel with the test; use the same test procedures; take all reagents in the same amount, but without adding samples. 7.4 LC-MS/MS test conditions Select appropriate test conditions according to the performance of the used LC- MS/MS and the actual situation of the sample. Because the test results depend on the used instrument, so, general parameters for chromatographic and mass spectrometric analysis cannot be given. The parameters which are listed in A.1 in Appendix A have been proven to be suitable for testing. 7.5 Preparation of standard working solution Weigh about 0.02 g of diuron (4.4), accurate to 0.1 mg, in a 100 mL volumetric flask; use methanol (4.1) to fix-volume to the mark. Then, adopt the stepwise dilution method; use a graduated pipette (5.6) or a one mark pipette (5.7) to transfer the above solution into a suitable volumetric flask (5.5); use methanol (4.1) to dilute the above solution to diuron standard working solution of applicable concentration. Note 1: The concentration range of diuron standard working solution can be adjusted according to the used instrument and sample. Note 2: It's also available to directly use a diuron standard solution of known concentration. 7.6 Drawing of the standard working curve Determine the diuron standard working solution (7.5) according to the conditions of LC-MS/MS of 7.4. Inject each standard working solution twice; take the average value of the peak areas; the relative deviation shall not be greater than 5%. Record multiple reaction monitoring (MRM) chromatograms based on quantitatively selected ions and qualitative ions (see Table A.1); take the peak area (minus the area of diuron in the non-standardized working solution) as the ordinate, and the corresponding standard working solution concentration as the abscissa, to draw the standard working curve. The standard working curve shall include at least 5 diuron standard working solutions (7.5). The linear correlation coefficient R2 of the standard working curve shall be greater than 0.995; otherwise, draw a new standard working curve. 7.7 Determination of extraction solutionAppendix A(Informative) LC-MS/MS reference conditions A.1 LC-MS/MS reference conditions A.1.1 Chromatographic column: C18 reversed-phase chromatographic column, 2.1 mm × 50 mm, 1.8 μm. A.1.2 Flow velocity: 0.3 mL/min. A.1.3 Column temperature: 35°C. A.1.4 Injection volume: 1 μL. A.1.5 Atomizing gas: nitrogen, purity ≥ 95%. A.1.6 Dry gas temperature: 350°C. A.1.7 Dry air flow: 9 L/min. A.1.8 Atomizing gas pressure: 344 737.85 Pa (50 psi). A.1.9 Collision gas: high-purity nitrogen, purity ≥ 99.999%. A.1.10 Mobile phase: water [5 mmol/L ammonium acetate, formic acid volume fraction 0.1%] + methanol (30 + 70). A.1.11 Mass ion source: electrospray ionization source (ESI). A.1.12 Ionization method: positive-ion scanning. A.1.13 Capillary voltage: +3 000 V. A.1.14 Monitoring mode: multiple reaction monitoring (MRM), see Table A.1 for the monitoring conditions. Table A.1 -- Diuron multiple reaction monitoring conditions Compound name Parent ion m/z Daughter ion m/z Collision energy (CE)/eV Declustering potential/ Acceleration voltage/ Diuron 232.8 72.1 a 26 105 7 232.8 159.8 18 105 7 a quantitative daughter ion. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 37363.2-2019 be delivered?Answer: The full copy PDF of English version of GB/T 37363.2-2019 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 37363.2-2019_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 37363.2-2019_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 37363.2-2019 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 37363.2-2019?A step-by-step guide to download PDF of GB/T 37363.2-2019_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 37363.2-2019". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
