GB/T 34251-2017 PDF EnglishUS$115.00 · In stock · Download in 9 seconds
GB/T 34251-2017: Test method for metal marking resistance of glazed ceramic tableware Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 34251-2017: Test method for metal marking resistance of glazed ceramic tableware---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT34251-2017GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 81.060.20 Y 24 Test Method for Metal Marking Resistance of Glazed Ceramic Tableware ISSUED ON: SEPTEMBER 7, 2017 IMPLEMENTED ON: APRIL 1, 2018 Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative References ... 4 3 Principle ... 4 4 Reagent ... 4 5 Equipment and Appliances ... 4 6 Specimen ... 6 7 Procedures ... 6 8 Grading of Scratch Resistance Performance ... 6 9 Inspection Report ... 7 Test Method for Metal Marking Resistance of Glazed Ceramic Tableware1 ScopeThis Standard specifies the test method of determining the metal marking resistance of glazed ceramic tableware at room temperature. This Standard is applicable to glazed plate products that are in contact with metal cutlery, such as: daily-use porcelain, stoneware and pottery, etc.2 Normative ReferencesThe following documents are indispensable to the application of this document. In terms of references with a specified date, only versions with a specified date are applicable to this document. In terms of references without a specified date, the latest version (including all the modifications) is applicable to this document. GB/T 1220 Stainless Steel Bars GB/T 3280 Cold Rolled Stainless Steel Plate, Sheet and Strip3 PrincipleSimulate the mode of using a table knife, adopt a standard cutting tool to scratch the ceramic glaze back and forth in a straight line under a specific force, observe the severity of the scratch on the glaze, and determine its scratch resistance to metal tableware.4 ReagentAbsolute ethanol (chemically pure).5 Equipment and Appliances5.1 Scratch Resistance Performance Tester As it is shown in Figure 1. The temperature is controlled within 5C. 5.4 Balance The accuracy is 0.1 g.6 SpecimenTake the plate products of the same production batch specification and the same type of ware. The surface of the sample shall be free from defects, such as: cracks, lack of glaze and thin glaze, etc.7 Procedures7.1 Use sponge or cotton cloth dipped in absolute ethanol to wipe the glazed surface of the sample, then, use tap water to rinse it and use a dry cloth to dry it. At 105 C 5 C, dry it in a drying oven. Take it out, then cool it to room temperature. 7.2 Horizontally place the sample on the working platform, select a suitable scratching position (for example, the part where the table knife is often used), adjust the fastening pressure bar to compress the sample, ensure that the sample will not be loosened during the test. 7.3 Clamp the standard cutting tool, make the tool face perpendicular to the ceramic glaze. The tool edge is in parallel contact with the glaze. 7.4 Adjust the balance weight, so that the tool edge is just in contact with the glaze without any applied force. 7.5 Load the counterweight, so that the force of the cutting tool acting on the glaze is 10 N. 7.6 Turn on the power switch and carry out the scratching test. Make 3 scratches on each sample, and for each scratch, scratch for 4 times (one back and forth cycle of the cutting tool is recorded as 2 times of scratch). The parallel interval between the scratches is 10 mm. 7.7 After scratching, turn off the power switch and loosen the fastening pressure bar; remove the sample and use absolute ethanol to wipe it. 7.8 Under natural light or artificial lighting conditions, at a distance of about 25 cm from the glazed surface, conduct visual inspection.8 Grading of Scratch Resistance PerformanceFrom the three scratches, select two with similar degrees to conduct the determination in accordance with Table 1. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 34251-2017 be delivered?Answer: The full copy PDF of English version of GB/T 34251-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 34251-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 34251-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 34251-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 34251-2017?A step-by-step guide to download PDF of GB/T 34251-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 34251-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
