GB/T 33625-2017 PDF EnglishUS$150.00 · In stock · Download in 9 seconds
GB/T 33625-2017: Oil-free Reciprocating Air Compressor on Locomotives and Power Cars Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 33625-2017: Oil-free Reciprocating Air Compressor on Locomotives and Power Cars---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT33625-2017GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 23.140 J 72 Oil-free Reciprocating Air Compressor on Locomotives and Power Cars Issued on: MAY 12, 2017 Implemented on: DECEMBER 1, 2017 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. 3. No action is required - Full-copy of this standard will be automatically & immediately delivered to your EMAIL address in 0~60 minutes. Table of ContentsForeword ... 3 1 Application Scope ... 4 2 Normative References ... 4 3 Requirements ... 5 4 Test Methods ... 7 5 Inspection Rules ... 9 6 Marking, Packaging and Storage ... 10ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard was proposed by China Machinery Industry Federation. This Standard shall be under the jurisdiction of the National Standardization Technical Committee on Compressors (SAC/TC 145). The drafting organizations of this Standard. Hefei General Machinery Research Institute, Hefei General Environment Control Technology Co., Ltd., Jiangsu Dehou Electric Co., Ltd. The main drafters of this Standard. Zhang Chenyan, Liu Cen, Wang Shusheng, Gao Xiangjia, Zhang Jinan. Oil-free Reciprocating Air Compressor on Locomotives and Power Cars1 Application ScopeThis Standard specifies the requirements, test methods, inspection rules and marking, packaging and storage of air-cooling, single-stage, single-action, direct-drive oil-free reciprocating air compressors (hereinafter referred to as “air compressors”) used on the pantograph system of locomotives and power cars. This Standard applies to air compressors used on the pantograph system of locomotives and power cars, whose rated discharge pressure is not greater than 1.0 MPa.2 Normative ReferencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition dated applies to this document. For undated references, the latest edition of the referenced documents (including all amendments) applies to this Standard. GB/T 755, Rotating Electrical Machines – Rating and Performance GB/T 3853, Displacement Compressor – Acceptance Tests GB/T 4208, Degrees of Protection Provided by Enclosure (IP Code) GB/T 4980, Determination of Sound Level for Noise Emitted by Displacement Compressors GB/T 7777, Measurement and Evaluation of Mechanical Vibration of Displacement Compressors GB/T 9438, Aluminum Alloy Castings GB/T 9440, Malleable Iron Castings GB/T 11021, Electrical Insulation – Thermal Evaluation and Designation GB/T 13306, Plate GB/T 15115, Die Casting Aluminum Alloys GB/T 15487, Methods of Flow Measurement for Displacement Compressor GB 19153, Minimum Allowable Values of Energy Efficiency and Energy Efficiency Grades for Displacement Air Compressors GB/T 21563-2008, Railway Applications – Rolling Stock Equipment – Shock and Vibration Tests GB 22207, Safety Requirements of Displacement Air Compressor JB/T 6431, Gray Iron Castings for Displacement Compressor – Specification JB/T 7663.1, Packaging Technical Condition of Displacement Compressors JB/T 7663.2, Coating Specifications for Displacement Compressors JB/T 8934, Direct Drive Portable Reciprocating Piston Air Compressor JB/T 9104, The Technical Specification for Spheroidal Araphite Iron Castings of Displacement Compressors TB/T 1126, Standard Voltage for Locomotive Control and Light Circuit3 Requirements3.1 General requirements 3.1.1 Air compressors shall comply with this Standard; they shall be manufactured in accordance with the drawings and technical documents which are approved through specified procedures. 3.1.2 Specified operating conditions of air compressors a) suction pressure. 0.1 MPa (absolute pressure); b) suction temperature. 20°C; c) suction relative humidity. 0; d) rated discharge pressure. 0.8 MPa; e) operating voltage. DC 110 V; f) rotational speed. as specified in the product technical documents, expressed in r/min. 3.1.3 Air compressors shall be capable of operating normally under the following service environmental conditions. a) the altitude not more than 2 500 m; 4.1.2 The testing of the input specific power of air compressors shall be conducted as specified in GB 19153. 4.1.3 The testing of the noise power level of air compressors shall be conducted as specified in GB/T 4980. 4.1.4 The testing of the mechanical vibration intensity of air compressors shall be conducted as specified in GB/T 7777. 4.2 Environment adaptation 4.2.1 High-temperature test 4.2.1.1 After storing air compressors for 2 h under the environmental conditions of 40°C, start the machine for continuous operation for 2 h. the operating voltage during operation is DC 110 V and the discharge pressure is the rated discharge pressure. Measure the discharge temperature of air compressors at this moment, which shall be as specified in this Standard. 4.2.1.2 Install the air compressors under the environmental conditions of 70°C which are installed inside the car body in actual use or install the air compressors under the environmental conditions of 50°C which are installed inside the car body; store for 2 h; start the machine to run continuously for 10 min. the operating voltage during operating is DC 110 V and the discharge pressure is the rated discharge pressure. Measure the discharge temperature of air compressors at this moment, which shall be as specified in this Standard. 4.2.2 Low-temperature test After storing air compressors for 2 h under the environmental conditions of - 40°C, air compressors shall be capable of being started normally under the operating voltage of DC 77 V and operating continuously for 1 h under the rated discharge pressure. 4.2.3 High-altitude test The test shall be conducted in areas of altitude 2 500 m or simulated in a low air pressure testing chamber in the library. The environmental pressure of the testing chamber during the simulation test is 75 kPa. The test time is 30 min; air compressors shall be capable of operating normally under the rated pressure ratio. 4.2.4 Impact and vibration test Conduct impact and vibration test for the air compressors in accordance with the provisions for equipment class A, category 1 specified in GB/T 21563-2008. Conduct inspection for the connectors and appearance after test. Operate continuously for 2 h under the rated discharge pressure, no abnormality shall occur during operation. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 33625-2017 be delivered?Answer: The full copy PDF of English version of GB/T 33625-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 33625-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 33625-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 33625-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 33625-2017?A step-by-step guide to download PDF of GB/T 33625-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 33625-2017". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
