GB/T 32569-2016 PDF EnglishUS$90.00 · In stock · Download in 9 seconds
GB/T 32569-2016: Welded stainless steel tubes for seawater desalination plants Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 32569-2016: Welded stainless steel tubes for seawater desalination plants---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT32569-2016GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.140.75 H 48 Welded stainless steel tubes for seawater desalination plants Issued on: FEBRUARY 24, 2016 Implemented on: JANUARY 1, 2017 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Order contents ... 7 4 Dimension, shape and tolerance ... 7 5 Technical requirements ... 8 6 Test methods ... 14 7 Inspection rules ... 15 8 Packaging, symbols and quality certificate ... 16ForewordThis Standard was drafted in accordance with the rules given in GB/T 1.1-2009. This Standard was proposed by China Iron and Steel Association. This Standard shall be under the jurisdiction of the National Technical Committee for Standardization of Steels (SAC/TC 183). Drafting organizations of this Standard. Hunan Xiangtou Goldsky New Materials Co., Ltd, Shandong Taishan Iron and Steel Group Co., Ltd, Jiangsu Wujin Stainless Steel Pipe Group Co., Ltd, Chengdu Common Tube Group Co., Ltd, Shanxi Taigang Stainless Steel Co., Ltd, and Hunan Green & Innovative Materials Co., Ltd. Main drafters of this Standard. Xie Yi, Li Jianfei, Qi Haiyan, Song Jianxin, Wen Changhong, Kang Xitang, Yan Xinliang, Yue Weiheng and Li Huaize. Welded stainless steel tubes for seawater desalination plants1 ScopeThis Standard specifies the dimension, shape, tolerance, technical requirements, test methods, inspection rules, packaging, symbols and quality certificate of the welded stainless steel tubes for seawater desalination plants (hereinafter referred to as “steel tubes”). This Standard is applicable to the welded stainless steel tubes for the heat exchangers of seawater desalination plants.2 Normative referencesThe following documents are essential to the application of this document. For dated references, only the editions with the dates indicated are applicable to this document. For undated references, only the latest editions (including all the amendments) are applicable to this document. GB/T 222 Permissible tolerances for chemical composition of steel products GB/T 223.5 Steel and iron - Determination of acid-soluble silicon and total silicon content - Reduced molybdosilicate spectrophotometric method GB/T 223.9 Iron, steel and alloy - Determination of aluminium content - Chrom azurol S photometric method GB/T 223.11 Iron, steel and alloy - Determination of chromium content - Visual titration or potentiometric titration method GB/T 223.16 Methods for chemical analysis of iron, steel and alloy - The chromotropic acid photometric method for the determination of titanium content GB/T 223.18 Methods for chemical analysis of iron, steel and alloy - The sodium thiosulfate separation iodimetric method for the determination of copper content GB/T 223.23 Iron, steel and alloy - Determination of nickel content - The dimethylglyoxime spectrophotometric method GB/T 223.25 Methods for chemical analysis of iron, steel and alloy - The dimethylglyoxime gravimetric method for the determination of nickel content GB/T 223.26 Iron, steel and alloy - Determination of molybdenum content - The thiocyanate spectrophotometric method GB/T 223.28 Methods for chemical analysis of iron, steel and alloy - The α- benzoinoxime gravimetric method for the determination of molybdenum content GB/T 223.30 Methods for chemical analysis of iron, steel and alloy - The arsenazo III spectrophotometric method for the determination of zirconium content after separation by p-bromomandelic acid GB/T 223.37 Methods for chemical analysis of iron, steel and alloy - The indophenol blue photometric method for the determination of nitrogen content after distillation separation GB/T 223.40 Iron, steel and alloy - Determination of niobium content by the sulphochlorophenol S spectrophotometric method GB/T 223.43 Iron, steel and alloy - Determination of tungsten content - Gravimetric method and spectrophotometric method GB/T 223.58 Methods for chemical analysis of iron, steel and alloy - The sodium arsenite-sodium nitrite titrimetric method for the determination of manganese content GB/T 223.59 Iron, steel and alloy - Determination of phosphorus content - Bismuth phosphomolybdate blue spectrophotometric method and antimony phosphomolybdate blue spectrophotometric method GB/T 223.60 Methods for chemical analysis of iron, steel and alloy - The perchloric acid dehydration gravimetric method for the determination of silicon content GB/T 223.68 Methods for chemical analysis of iron, steel and alloy - The potassium iodate titration method after combustion in the pipe furnace for the determination of sulfur content GB/T 223.69 Iron, steel and alloy - Determination of carbon contents - Gas- volumetric method after combustion in the pipe furnace GB/T 223.72 Iron, steel and alloy - Determination of sulfur content - Gravimetric method 4.1.3 According to the requirements of the demander, after the consultation between supplier and demander, and making indications in the contract, it is allowed to supply the steel tubes with other outer diameters, wall thicknesses and tolerances. 4.2 Out-of-roundness For the steel tubes, the out-of-roundness shall not exceed 75% of the tolerance of the nominal outer diameter. However, for the thin-walled steel tubes whose ratio OF wall thickness TO outer diameter is not greater than 3%, the out-of- roundness shall not exceed 2% of the nominal outer diameter. 4.3 Bending The bending of steel tubes shall not be greater than 1.5 mm/m. 4.4 End shape The end faces on both sides of each steel tube shall be perpendicular to the steel tube’s axis. Furthermore, REMOVE the burrs at the notches.5 Technical requirements5.1 Designations and chemical compositions of steels 5.1.1 The designations and chemical compositions (smelting analysis) of steels shall conform to the provisions of Table 2. According to the requirements of the demander, after the consultation between supplier and demander, and making indications in the contract, it is allowed to supply the steel tubes with other designations and chemical compositions. 5.1.2 The tolerances for the chemical compositions of finished steel tubes shall conform to the provisions of GB/T 222. 5.2 Manufacturing method 5.2.1 Steel tubes shall use rolled steel strips as raw materials, and automatic welding method without adding any filler metals for manufacture. 5.2.2 According to the requirements of the demander, after the consultation between supplier and demander, and making indications in the contract, it is allowed to conduct cold working to the steel tubes’ welding seams and base metal, or to only conduct cold working to the weld metal after welding and before final heat treatment. 5.3 Delivery status S - Nominal wall thickness of the steel tube, in unit of millimeter (mm); D - Nominal outer diameter of the steel tube, in unit of millimeter (mm); e - Coefficient of deformation per unit length. For the austenitic steel tubes and austenitic-ferritic duplex steel tubes, it shall be 0.09. For the ferritic steel tubes, it shall be 0.08. 5.6.2 Flanging test Steel tubes shall be conducted with flanging test. During the flanging test, the flanging width shall not be less than 15% of the outer diameter. After the test, there shall be no cracks on the test sample. 5.7 Non-destructive testing Steel tubes shall be conducted with eddy current testing one by one. During the eddy current testing, the artificial defects of the contrast tube shall conform to the provisions of the acceptance level B in GB/T 7735-2004. After the consultation between supplier and demander, and making indications in the contract, it is allowed to use other non-destructive testing methods. 5.8 Corrosion tests 5.8.1 Intergranular corrosion test 5.8.1.1 Austenitic steel tubes and ferritic steel tubes shall be conducted with intergranular corrosion test. After the test, the test samples are not allowed to have corrosion tendency. 5.8.1.2 For the austenitic steel tubes with the nominal outer diameters of less than 16mm, TAKE 25mm long whole tube section as test sample. CONDUCT the immersion corrosion according to the provisions of method E in GB/T 4334- 2008. FLATTEN the test sample according to the Step 1 in the provisions of Section 5.6.1. MAKE evaluation afterwards. For the austenitic steel tubes with the nominal outer diameters of not less than 16mm, the intergranular corrosion test methods shall conform to the provisions of method E in GB/T 4334-2008. 5.8.1.3 The ferritic steel tubes with the designations of 022Cr18Ti, 019Cr19Mo2NbTi and 008Cr27Mo shall be conducted with intergranular corrosion test according to the provisions of GB/T 32571. According to the requirements of the demander, after the consultation between supplier and demander, and makin... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 32569-2016 be delivered?Answer: The full copy PDF of English version of GB/T 32569-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 32569-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 32569-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 32569-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 32569-2016?A step-by-step guide to download PDF of GB/T 32569-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 32569-2016". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
