GB/T 31566-2015 PDF EnglishUS$130.00 · In stock · Download in 9 seconds
GB/T 31566-2015: Metallic coatings -- Physical vapour-deposited coatings of aluminium -- Specification and test methods Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 31566-2015: Metallic coatings -- Physical vapour-deposited coatings of aluminium -- Specification and test methods---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT31566-2015 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 25.220.40 A 29 GB/T 31566-2015 / ISO 22779.2006 Metallic coatings - Physical vapour-deposited coatings of aluminium - Specification and test methods (ISO 22779.2006, IDT) Issued on: MAY 15, 2015 Implemented on: JANUARY 1, 2016 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the People's Republic of China. Table of ContentsForeword ... 3 Introduction ... 5 1 Scope ... 6 2 Normative references ... 6 3 Terms and definitions ... 8 4 Information to be supplied by the purchaser to the processor ... 8 5 Designation ... 9 6 Requirements ... 12 7 Sampling ... 16 8 Rejection ... 17 Annex A (informative) Additional information concerning equipment, substrate preparation and process parameters ... 18 Annex B (normative) Determination of the average thickness of aluminium coatings ... 21 Annex C (normative) Adhesion test methods ... 22 Annex D (normative) Sampling ... 23 Bibliography ... 24ForewordThis Standard is drafted according to the rules given in GB/T 1.1-2009. This Standard uses the translation method to equivalently adopt ISO 22779.2006 “Metallic coatings - Physical vapour-deposited coatings of aluminium - Specification and test methods”. China’s national documents that have consistency correspondence relation with the normative-reference international documents in this Standard are as follows. - GB/T 3138-2015 Electroplating and related processes - Vocabulary (ISO 2080.2008, IDT) - GB/T 4957-2003 Non-conductive coatings on non-magnetic electrically conductive basis materials - Measurement of coating thickness - Amplitude-sensitive eddy- current method (ISO 2360.1982, IDT) - GB/T 5270-2005 Metallic coatings on metallic substrates - Electrodeposited and chemically deposited coatings - Review of methods available for testing adhesion (ISO 2819.1980, IDT) - GB/T 6462-2005 Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (ISO 1463.2003, IDT) - GB/T 6463-2005 Metallic and other inorganic coatings - Review of methods of measurement of thickness (ISO 3882.2003) - GB/T 9792-2003 Conversion coatings on metallic materials - Determination of coating mass per unit area - Gravimetric methods (ISO 3892.2000, MOD) - GB/T 10125-2012 Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227.2006, IDT) - GB/T 11378-2005 Metallic coatings - Measurement of coating thickness - Profilometric method (ISO 4518.1980, IDT) - GB/T 12334-2001 Metallic and other inorganic coatings - Definitions and conventions concerning the measurement of thickness (ISO 2064, IDT) - GB/T 12609-2005 Electrodeposited metallic coatings and related finishes - Sampling procedures for inspection by attributes (ISO 4519.1980, IDT) - GB/T 16921-2005 Metallic coatings - Measurement of coating thickness - X-ray spectrometric methods (ISO 3497.1990, IDT) - GB/T 19349-2012 Metallic and other inorganic coatings - Pretreatments of iron or steel to reduce the risk of hydrogen embrittlement (ISO 9587.2007, IDT) - GB/T 19350-2012 Metallic and other inorganic coatings - Post-coating treatments of iron or steel to reduce the risk of hydrogen embrittlement (ISO 9588.2007, IDT) - GB/T 19822-2005 Specification for hard anodic oxidation coatings on aluminium and its alloys (ISO 10074.1994, IDT) - GB/T 20015-2005 Metallic and other inorganic coatings - Automated controlled shot-peening of metallic articles prior to nickel, autocatalytic nickel or chromium plating, or as a final finish (ISO 12686.1999, IDT) - GB/T 20018-2005 Metallic and non-metallic coatings - Measurement of thickness - Beta backscatter method (ISO 3543.2000, IDT) - GB/T 20631.2-2006 Specifications for pressure-sensitive adhesive tapes for electrical purposes - Part 2. Methods of test (IEC 60454.1994, IDT) - GB/T 31563-2015 Metallic coatings - Measurement of coating thickness - Scanning electron microscope method (ISO 9220.1988, MOD) This Standard is proposed by China Machinery Industry Federation. This Standard shall be under the jurisdiction of National Technical Committee on Metallic and Nonmetallic Coatings of Standardization Administration of China (SAC/TC 57). Main drafting organizations of this Standard. Lanzhou Institute of Chemical Physics of Chinese Academy of Sciences, Naval University of Engineering of Chinese People’s Liberation Army, Chongqing Institute of Measurement and Quality Testing, Wuhan Material Protection Institute, Dongguan Yi’an Technology Co., Ltd., Shenzhen Fasite Precision Technology Co., Ltd. Main drafters of this Standard. Gao Xiaoming, Jiang Dong, Weng Lijun, Chen Debin, Yu Xiang, Gao Zhengyuan, Jia Jianxin, Li Weirong and Zhang Jun. Metallic coatings - Physical vapour-deposited coatings of aluminium - Specification and test methods1 ScopeThis Standard specifies requirements for aluminium coatings applied by physical vapour deposition techniques to mild steels, low-alloy steels, high-strength steels, corrosion-resisting steels, aluminium alloys, titanium alloys and other materials, as appropriate. Physical vapour-deposited coatings of aluminium are not suitable for steels having tensile strengths greater than 1 400 MPa, because of the possibility of hydrogen embrittlement due to corrosion in service or storage, or as a result of excessive cathodic protection. WARNING. The use of this Standard may involve hazardous materials, operations and equipment. This Standard does not address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and to determine the applicability of regulatory limitations prior to use.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1463 Metallic and oxide coatings - Measurement of coating thickness - Microscopical method ISO 2064 Metallic and other inorganic coatings - Definitions and conventions concerning the measurement of thickness ISO 2080 Electroplating and related processes - Vocabulary ISO 2360 Non-conductive coatings on non-magnetic electrically conductive basis materials - Measurement of coating thickness - Amplitude-sensitive eddy-current method ISO 2819 Metallic coatings on metallic substrates - Electrodeposited and chemically deposited coatings - Review of methods available for testing adhesion ISO 2859 Sampling procedures for inspection by attributes ISO 3497 Metallic coatings - Measurement of coating thickness - X-ray spectrometric methods ISO 3543 Metallic and non-metallic coatings - Measurement of thickness - Beta backscatter method ISO 3882 Metallic and other inorganic coatings - Review of methods of measurement of thickness ISO 3892 Conversion coatings on metallic materials - Determination of coating mass per unit area - Gravimetric methods ISO 4518 Metallic coatings - Measurement of coating thickness - Profilometric method ISO 4519 Electrodeposited metallic coatings and related finishes - Sampling procedures for inspection by attributes ISO 9220 Metallic coatings - Measurement of coating thickness - Scanning electron microscope method ISO 9227 Corrosion tests in artificial atmospheres - Salt spray tests ISO 9587 Metallic and other inorganic coatings - Pretreatments of iron or steel to reduce the risk of hydrogen embrittlement ISO 9588 Metallic and other inorganic coatings - Post-coating treatments of iron or steel to reduce the risk of hydrogen embrittlement ISO 10074 Specification for hard anodic oxidation coatings on aluminium and its alloys ISO 10546 Chemical conversion coatings - Rinsed and non-rinsed chromate conversion coatings on aluminium and aluminium alloys ISO 12686 Metallic and other inorganic coatings - Automated controlled shot- peening of metallic articles prior to nickel, autocatalytic nickel or chromium plating, or as a final finish ISO 16348 Metallic and other inorganic coatings - Definitions and conventions concerning appearance IEC 60454 Specifications for pressure-sensitive adhesive tapes for electrical ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 31566-2015 be delivered?Answer: The full copy PDF of English version of GB/T 31566-2015 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 31566-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 31566-2015_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 31566-2015 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 31566-2015?A step-by-step guide to download PDF of GB/T 31566-2015_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 31566-2015". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
