GB/T 25089-2010 PDF EnglishUS$130.00 · In stock · Download in 9 seconds
GB/T 25089-2010: Road vehicles -- Data cables Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 25089-2010: Road vehicles -- Data cables---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT25089-2010GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 43.040.10 T 36 Road vehicles - Data cables (ISO/TS 16553.2006, Road vehicles - Data cables – Test methods and requirements, MOD) Issued on: SEPTEMBER 02, 2010 Implemented on: FEBRUARY 01, 2011 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of the PRC. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 4 4 General requirements ... 5 5 Size ... 7 6 Electrical performance ... 8 7 Mechanical properties ... 12 8 Low temperature performance ... 12 9 Wear resistance ... 12 10 Heat aging ... 13 11 Environment and chemical resistance ... 13 12 Flame retardant ... 13 13 Artificial atmosphere aging ... 14ForewordThis standard, through modification, adopts ISO/TS 16553.2006 “Road vehicles - Data cables - Test methods and requirements”. This standard was redrafted in accordance with ISO/TS 16553.2006. The technical differences between the standard and ISO/TS 16553.2006 and the causes are as follows. - The definitions of 3.3 “Shielding” and 3.4 “Cable core” in the original text are repeated in the terms of GB/T 25087-2010 “Road vehicles - Round, screened and unscreened 60 V and 600 V multi-core sheathed cables”; in this standard, GB/T 25087-2010 is directed referenced AND the repeated definitions are deleted. - In accordance with the provisions on drafting of national standards, ADD the following information to the scope of application. This standard applies to type M, N, O, L vehicle data cable. As compared with ISO/TS 16553.2006, the editorial changes are as follows. - CHANGE “this international standard” in the original text into “this standard”; - DELETE the final references from the international standard. This standard was proposed by the National Development and Reform Commission. This standard shall be under the jurisdiction of the National Automobile Standardization Technical Committee. The drafting organization of this standard. Beijing Force Automotive Wire Co., Ltd. The main drafters of this standard. Wang Yadong, Huo Yan, Dong Xigang, Li Qingsen. Road vehicles - Data cables1 ScopeThis standard specifies the test methods and requirements for shielded and unshielded, sheathed and non-sheathed twisted pair data cables and coaxial pair cables for road vehicles. As for the sheathed cables, SEE GB/T 25087- 2010 “Road vehicles - Round, screened and unscreened 60 V and 600 V multi- core sheathed cables”. As for the rated temperature class, SEE GB/T 25085- 2010 “Road vehicles - 60 V and 600 V single-core cables”. This standard applies to type M, N, O, L vehicle data cable.2 Normative referencesThe provisions in following documents become the provisions of this Standard through reference in this Standard. For the dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this Standard; however, parties who reach an agreement based on this Standard are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies. GB/T 25085-2010 Road vehicles - 60 V and 600 V single-core cables (ISO 6722.2006, IDT) GB/T 25087-2010 Road vehicles - Round, screened and unscreened 60 V and 600 V multi-core sheathed cables (ISO 14572.2006, IDT) ASTM D 4566 Standard test methods for electrical performance properties of insulations and jackets for telecommunications wire and cable3 Terms and definitionsThe terms and definitions as established in GB/T 25087-2010 and the following apply to this standard. 3.1 Capacitance5 Size5.1 Cable outer diameter It shall follow 5.2 of GB/T 25087-2010. 5.2 Sheath ellipticity It shall follow 5.3 of GB/T 25087-2010, AND whether this test is used is to be determined by the supplier and the buyer through negotiation. 5.3 Sheath thickness It shall follow 5.4 of GB/T 25087-2010. 5.4 Twisted pair pitch 5.4.1 Overview This test is only applicable to unshielded twisted pairs. Whether this test is used is to be determined by the supplier and the buyer through negotiation. 5.4.2 Test specimen PEEL the sheath from the 1 m length cable; ENSURE that the twisted pair ends are not scattered. It may also use other lengths based on the cable length. 5.4.3 Device It shall use the measurement device of precision ± 1.0 mm. 5.4.4 Procedure CLAMP the test specimen to prevent loosening. MEASURE the length of the five pitches; AND a single pitch is the travel length for one turn along the axial single line of the twisted pair. The average length of a single pitch is the measured length divided by 5. 5.4.5 Requirements The average pitch length shall be within the scope as determined by the supplier and the buyer through negotiation. L2 - Length of the second test specimen, m. 6.4.4 Requirements The values of C, CA, and CB are to be determined by the supplier and the buyer through negotiation. 6.5 Linear delay 6.5.1 Test application Whether this test is used is to be determined by the supplier and the buyer through negotiation. 6.5.2 Test specimen From one end of a 3 m length test specimen, PEEL 50 mm sheath; and PEEL 12 mm insulation from both ends of the cable core. 6.5.3 Device The measurement device used is a network analyzer. 6.5.4 Procedures It shall follow ASTM D 4566. USE the network analyzer to measure the phase constant at 1 MHz. USE the following equation to calculate linear delay. Where. w - Angular frequency, rad/s; β - Phase constant, rad; tp - Linear delay, ns/m; L - Length of test specimen, m. 6.5.5 Requirements The calculated value shall be within the range as determined by the supplier and the buyer through negotiation. 6.6 Shielding efficiency10 Heat aging10.1 3000h long-term aging This test is used to determine the “rated temperature class”. AND it shall follow 10.1 of GB/T 25087-2010. 10.2 240h short-term aging This test is used to simulate the thermal drift. AND it shall follow 10.2 of GB/T 25087-2010. 10.3 Heat shrinkage of sheath It shall follow 10.4 of GB/T 25087-2010. AND whether this test is used is to be determined by the supplier and the buyer through negotiation.11 Environment and chemical resistance11.1 Sheath liquid resistance It shall follow 11.1 of GB/T 25087-2010. AND whether this test is used is to be determined by the supplier and the buyer through negotiation. 11.2 Sheath marking durability It shall follow 11.2 of GB/T 25087-2010. AND whether this test is used is to be determined by the supplier and the buyer through negotiation. 11.3 Sheath ozone resistance It shall follow 11.3 of GB/T 25087-2010. AND whether this test is used is to be determined by the supplier and the buyer through negotiation. 11.4 Alternating temperature and humidity It shall follow 11.4 of GB/T 25087-2010. AND whether this test is used is to be determined by the supplier and the buyer through negotiation.12 Flame retardantIt shall follow the chapter 12 of GB/T 25087-2010. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 25089-2010 be delivered?Answer: The full copy PDF of English version of GB/T 25089-2010 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 25089-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 25089-2010_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 25089-2010 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 25089-2010?A step-by-step guide to download PDF of GB/T 25089-2010_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 25089-2010". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
