GB/T 23341.2-2018 PDF EnglishUS$325.00 · In stock · Download in 9 seconds
GB/T 23341.2-2018: Turbochargers - Part 2: Test methods Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 23341.2: Historical versions
Similar standardsGB/T 23341.2-2018: Turbochargers - Part 2: Test methods---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT23341.2-2018NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 27.020 J 91 Replacing GB/T 23341.2-2009 Turbochargers - Part 2.Test methods Issued on. FEBRUARY 06, 2018 Implemented on. SEPTEMBER 01, 2018 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the People's Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative references... 5 3 Terms and definitions... 5 4 Technical requirements for test equipment... 6 5 General conditions for tests... 8 6 Test items and methods... 8 Annex A (informative) Record sheet for compressor performance test... 28 Annex B (informative) Record sheet for turbine performance test... 30 Annex C (informative) Record sheet for supercharger self cycle test... 31 Annex D (informative) Schematic diagram of turbine casing flow capacity test... 332 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 2624 (all parts), Full differential pressure device installed in a pipe of circular cross-section measuring fluid flow GB/T 23341.1-2018, Turbochargers - Part 1.General requirements JB/T 6002-2007, Turbochargers. Limit values and measurement methods for cleanliness JB/T 9752.3, Turbochargers - Part 3.Balance quality requirements and check methods of rotors JB/T 12334-2015, Measuring method for noise of turbochargers JB/T 12335-2015, Turbochargers. Leakage test method3 Terms and definitionsFor the purposes of this document, the terms and definitions defined in GB/T 23341.1 as well as the followings apply. 3.1 hot blast test The test that the external source compressed air is heated and input to the turbine, and the supercharger is driven by the thermal expansion of the high-temperature gas. 3.3 compressor surge flow The speed of the supercharger is constant. When the flow rate of the compressor decreases to a certain value, the outlet pressure and speed of the compressor will fluctuate violently. Compressor surge flow refers to the corresponding flow value at this time. 3.4 compressor choke flow The speed of the supercharger is constant. With the reduction of the compressor pressure ratio, the flow of the compressor does not increase any more. Compressor choke flow refers to the corresponding flow value at this time.4 Technical requirements for test equipment4.1 Test bench pipeline 4.2 Measurement of rotate speed The rotate speed of the supercharger shall be measured by a method that does not disturb the flow, such as the non-contact electromagnetic sensor tube speed measurement or photoelectric speed measurement instrument for the magnetization of the compressor impeller lock nut. Instrument accuracy is ±0.2% of full scale. 4.3 Pressure measurement 4.3.3 Ambient barometric pressure measurement. Instrument accuracy is ±2% of full scale. 4.4 Temperature measurement 4.4.1 Compressor and turbine inlet and outlet temperatures shall be measured in circular section measuring tubes by electrical thermometers with stagnant sheaths. The measuring point shall be arranged at a position of 0.5 times the pipe diameter behind the static pressure measuring point (in the direction of the airflow). It shall be staggered from the pressure measuring point. 4.4.2 When measuring the performance of the compressor, the accuracy of the instrument is ±0.3% of the full scale. When measuring turbine performance, the instrument accuracy is ±0.5% of full scale. For other measurement of turbine inlet and outlet temperature, the instrument accuracy is ±1% of full scale. 4.4.3 Lubricating oil temperature measurement. Instrument accuracy is ±2% of full scale. 4.5 Flow measurement Compressor flow measurement can be carried out by gas mass flowmeter or standard orifice flowmeter or end-face intake double-wire flowmeter.5 General conditions for tests5.1 The supercharger used for the test shall meet the requirements of the product technical documents and pass the inspection. 5.4 During the test, unless otherwise specified, the following parameters shall be controlled.6 Test items and methods6.1 Compressor performance test 6.1.1 Test conditions The performance test of the compressor shall be carried out on a special bench that can adjust the working conditions and measurable parameters. The test bench and test conditions shall comply with the provisions of Chapter 4 and Chapter 5. 6.1.2 Test methods 6.1.2.3 During the test, each equal-conversion speed line is measured point by point from surge flow to choke flow. Between the surge flow and the choke flow, the measurement points shall be no less than 6 points, evenly distributed. When the compressor runs close to the surge area, the total pressure fluctuation range of the compressor outlet is more than 10%. At this time, the supercharger is accompanied by a regular abnormal noise. Compressor air flow shall be adjusted slowly. Control the total pressure fluctuation of the compressor outlet within 2%. Measure the compressor surge flow point. 6.1.3 Test steps Carry out the test according to the following test steps. stopped running. 6.1.4 Measurement parameters During the test, measure the following parameters. 6.1.5 Data processing According to the parameters measured in the test, according to the relevant formulas in GB/T 23341.1-2018, calculate compressor conversion flow, compressor efficiency, compressor pressure ratio. 6.2 Turbine performance test 6.2.1 Test conditions The test shall be carried out on a special bench that can adjust the working conditions and measurable parameters. The test bench and test conditions shall comply with the Compressor model. 65656 Compressor impeller model. 662 provisions of Chapter 4 and Chapter 5. 6.2.2 Test methods 6.2.3 Test steps Carry out the test according to the following test steps. 6.2.4 Measurement parameters During the test, measure the following parameters. 6.2.5 Data processing According to the parameters measured in the test, according to the relevant formulas in GB/T 23341.1-2018, calculate turbine resemble flow, turbine efficiency, expansion ratio. Take the expansion ratio πT as the abscissa. 6.3.5 Data processing According to the parameters measured in the test, according to the relevant formulas in GB/T 23341.1-2018, calculate supercharger performance parameters such as compressor pressure ratio πc, compressor conversion flow Gcnp, compressor efficiency ηc and supercharger total efficiency ηTc. The self cycle performance test data can be recorded in the format of Annex C. 6.4 Supercharger noise test According to JB/T 12334-2015. 6.5 Characteristic test of turbocharger lubricating oil supply 6.5.1 Test conditions The test bench shall comply with the provisions of Chapter 4.In addition to the provisions in Chapter 5, the test conditions shall also meet the following provisions. 6.5.3 Test steps Carry out the test according to the following test steps. 6.5.4 Measurement parameters During the test, measure the following parameters. 6.6 Casing containment test of supercharger 6.6.1 Test conditions The test shall be carried out on a special bench that can adjust the working conditions and measurable parameters. In addition to the test bench and test conditions shall meet the provisions of Chapter 4 and Chapter 5, the test bench shall also be equipped with safety protection devices and video recording system. 6.8.3 Test steps Carry out the 200h reliability endurance thermal cycle assessment test of the supercharger according to the following test steps. 6.8.4 Measurement parameters During the test, make a check and measurement record every 1h during the calibration parameter operation test. The lubricating oil flow is measured and recorded every 10h. The thermal cycle operation test is measured and recorded every 1h. Measure the following parameters. 6.9 Turbine casing flow capacity test 6.9.1 Test conditions The test shall be carried out on a special bench for the turbine casing flow capacity test that can adjust the working conditions and measurable parameters. The test bench shall be debugged. The instruments and meters are calibrated accurately. The operation test is reliable. 6.9.3 Test steps Carry out the test according to the following test steps. 6.10 Determination of supercharger cleanliness According to chapter 4 of JB/T 6002-2007, determine the cleanliness of the supercharger. 6.11 Dynamic balance test of supercharger Test according to JB/T 9752.3. 6.12 Tightness test of supercharger Carry out the sealing test of the supercharger according to Chapter 5 of JB/T 12335- 2015. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 23341.2-2018 be delivered?Answer: The full copy PDF of English version of GB/T 23341.2-2018 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 23341.2-2018_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 23341.2-2018_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 23341.2-2018 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 23341.2-2018?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 23341.2-2018 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 23341.2-2018?A step-by-step guide to download PDF of GB/T 23341.2-2018_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 23341.2-2018". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
