GB/T 19388-2003 PDF EnglishUS$140.00 · In stock · Download in 9 seconds
GB/T 19388-2003: Test methods of measuring rolling circumference for passenger car tyres Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 19388-2003: Test methods of measuring rolling circumference for passenger car tyres---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT19388-2003GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 83.160.10 G 41 Test Methods of Measuring Rolling Circumference for Passenger Car Tyres (ISO 17269.2000, Passenger Car Tyres – Methods for Measuring Rolling Circumference – Loaded New Tyres, MOD) Issued on: NOVEMBER 10, 2003 Implemented on: JUNE 1, 2004 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China Table of ContentsForeword... 3 1 Scope... 4 2 Normative Reference... 4 3 Terms and Definitions... 4 4 Drum Method... 5 5 Test Method of Vehicle Road... 8 6 Test Report... 11 Appendix A (Informative) Comparison of Clause Numbers between This Standard and Those of ISO 17269.2000... 12 Appendix B (Informative) Technical Differences and Their Causes between This Standard and ISO 17269.2000... 13 Appendix C (Normative) Tolerance of Test Device... 14ForewordThis Standard modified and adopted ISO 17269.2000 Passenger Car Tyres – Methods for Measuring Rolling Circumference – Loaded New Tyres (English Version). This Standard was redrafted according to ISO 17269.2000.Appendix A lists the comparison list of clause numbers between this standard and those of ISO 17269.2000. When adopting international standards, this Standard has made some modifications based on China's actual situation and operational needs. Compared with ISO 17269.2000, this Standard adds Clause 6 "Test Report". The relevant technical differences are marked with a vertical single line in the margin of the clauses they involve. A list of these technical differences is given in Appendix B for reference. For ease of use, this Standard has also made the following editorial changes. a) Change 'this international standard' into 'this Standard'; b) Use the decimal point '.' to replace ',' as a decimal point; c) Delete the foreword of the international standard; d) State directly the content of ISO 4000-1.2000, the reference document of ISO 17269.2000, in the text of the standard (see 4.6.1, 4.7, 5.6.2, 5.6.3 of this Edition). Appendixes A and B of this Standard are informative; while Appendix C is a normative. This Standard was proposed by the China Petroleum and Chemical Industry Association. This Standard shall be under the jurisdiction of the National Technical Committee on Tires and Rim of Standardization Administration of China. This Standard is entrusted to the National Technical Committee on Tires and Rim of Standardization Administration of China for interpretation. Drafting organization of this Standard. Beijing Research & Design Institute of Rubber Industry. Chief drafting staffs of this Standard. Chen Minling, Wang Kexian, Wu Jiangtao, and Xu Lihong. Test Methods of Measuring Rolling Circumference for Passenger Car Tyres1 ScopeThis Standard specifies two test methods for measuring the rolling circumference and the number of revolutions per unit distance (kilometers) of passenger car tires under load conditions. The first method is the drum method and the second method is the vehicle road method. This Standard applies to all new passenger car tires.2 Normative ReferenceThe provisions in following documents become the provisions of this Standard through reference in this Standard. For dated references, the subsequent amendments (excluding corrigendum) or revisions do not apply to this Standard, however, parties who reach an agreement based on this Standard are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies. GB/T 6326 Tyre terms (GB/T 6326-1994, neq ISO 3877-1.1978, ISO 4223.1989)3 Terms and DefinitionsFor the purposes of this Document, the terms and definitions given in GB/T 6326 and the following apply. 3.1 Revolutions per unit distance The number of full and partial revolutions that a tire makes when its (axle) center moves a unit distance of exactly 1 km. The number of revolutions per kilometer of a tire can be calculated by dividing 1 by the rolling circumference of the tire and multiplying by 106. 3.2 Rolling circumference of tyre; Cr The distance a tire covers in one complete rotation.4 Drum Method4.1 Principle The test tire-rim assembly is mounted on the driven shaft, pressed against a drum of a specified diameter, and a load is applied. The value of the rolling circumference is determined by a specific speed. The number of revolutions of the tire and drum is recorded; and these data are substituted into the formula to calculate the rolling circumference of the tire. 4.2 Test drum requirements 4.2.1 Diameter The diameter of the test drum for standard tests shall be 1,700 mm ± 17 mm. Other test drums shall have a diameter of at least 1,200 mm, but are not used for inter-laboratory comparative analysis. The drum shall have the ability to drive a driven wheel so that the tire is fixed and pressurized on the driving drum. Smooth operation shall be observed during measurement. 4.2.2 Surface The drum surface shall be a smooth steel surface. If a drum with a textured surface is used, this shall be noted in the test report. The drum surface shall be kept clean. 4.2.3 Width The width of the drum test surface shall be greater than the tread width of the test tire. 4.3 Thermal environment The test shall be conducted at a standard room temperature of 25°C. It can also be conducted in a temperature range of 20°C ~ 30°C without requiring temperature correction. 4.4 Speed The test speed of the drum shall be 80 km/h. For radial tires, within the speed range of 80 km/h ± 50 km/h, it can be assumed that the rolling circumference of the tire is linearly related to the speed. Within this range, the rolling circumference value at a speed of 80 km/h can be obtained by linear interpolation. 4.5 Accuracy The minimum number of pulses per revolution (Ni) of the tire and the drum shall be both 10. The total number of pulses during the measurement shall be greater than 1,000. 4.6 Test tire parameters ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 19388-2003 be delivered?Answer: The full copy PDF of English version of GB/T 19388-2003 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 19388-2003_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 19388-2003_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 19388-2003 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 19388-2003?A step-by-step guide to download PDF of GB/T 19388-2003_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 19388-2003". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
