GB/T 17888.1-2020 PDF EnglishUS$215.00 · In stock · Download in 9 seconds
GB/T 17888.1-2020: Safety of machinery. Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 17888.1: Historical versions
Similar standardsGB/T 17888.1-2020: Safety of machinery. Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT17888.1-2020 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 13.110 J 09 GB/T 17888.1-2020 / ISO 14122-1:2016 Replacing GB/T 17888.1-2008 Safety of Machinery – Permanent Means of Access to Machinery – Part 1: Choice of Fixed Means and General Requirements of Access (ISO 14122-1:2016, IDT) ISSUED ON: NOVEMBER 19, 2020 IMPLEMENTED ON: JUNE 01, 2021 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword ... 3 Introduction ... 5 1 Scope ... 7 2 Normative References ... 7 3 Terms and Definitions ... 8 4 Significant Hazards ... 10 5 General Requirements for Design and Construction ... 10 6 Requirements for the Selection of the Fixed Means of Access ... 11 6.1 General ... 11 6.2 Preferred means of access ... 11 6.3 Selection of the means of access ... 12 6.4 Selection between a ramp or a stair ... 13 6.5 Selection between stepladder and fixed ladder ... 14 7 General Requirements for Information for Use ... 14 7.1 Instruction handbook ... 14 7.2 Warnings ... 15 Annex A (Informative) Examples for the Changes in the Machine or System to Make Better Access Possible ... 16 Annex B (Informative) Significant Technical Changes between this Part and the GB/T 17888.1-2008 ... 17 Bibliography ... 18ForewordGB/T 17888 Safety of Machinery – Permanent Means of Access to Machinery constitutes the following four parts: --- Part 1: Choice of a Fixed Means and General Requirements of Access; --- Part 2: Working Platforms and Walkways; --- Part 3: Stairs, Stepladders and Guard-Rails; --- Part 4: Fixed Ladders. This Part is Part 1 of GB/T 17888. This Part was drafted as per the rules specified in GB/T 1.1-2009. This Part replaced GB/T 17888.1-2008 Safety of Machinery – Permanent Means of Access to Machinery – Part 1: Choice of a Fixed Means of Access between Two Levels. Compared with GB/T 17888.1-2008, the major technical changes of this Part can refer to Annex B. This Part used the translation method to equivalently adopt ISO 14122-1:2016 Safety of Machinery – Permanent Means of Access to Machinery – Part 1: Choice of Fixed Means and General Requirements of Access. The Chinese documents that have consistent correspondence with the international documents normatively cited in this Part are as follows: --- GB/T 15706-2012 Safety of Machinery - General Principles for Design - Risk Assessment and Risk Reduction (ISO 12100:2010, IDT) --- GB/T 17888.3-2020 Safety of Machinery - Permanent Means of Access to Machinery - Part 3: Stairs, Stepladders and Guard-Rails (ISO 14122-3:2016, IDT) --- GB/T 17888.4-2020 Safety of Machinery - Permanent Means of Access to Machinery - Part 4: Fixed Ladders (ISO 14122-4:2016, IDT) This Part was proposed by and under the jurisdiction of National Technical Committee on Mechanical Safety of Standardization Administration of China (SAC/TC 208). Drafting organizations of this Part: Tianjin Jinmao Group Co., Inc.; Jiangsu Guolang Machinery Manufacturing Co., Ltd.; Ningguo Dongfang Wear-Resistant Materials Co., Ltd.; Wright Housewares Co., Ltd. Foshan; Zhengzhou Guizhu Industry and Trading Co., Ltd.; China Productivity Center for Machinery; Shanghai Ruiju Metal Products Co., Ltd.; Shenyang Yongpan Metal Products Co., Ltd.; Zhejiang Aopeng Industry and Trading Co., Ltd.; Ningbo Vichnet Technology Co., Ltd.; Nanjing Forestry University/National-Provincial Joint Engineering Research Center of Biomaterials for Electromechanical Product Packaging; Safety of Machinery – Permanent Means of Access to Machinery – Part 1: Choice of Fixed Means and General Requirements of Access1 ScopeThis Part of GB/T 17888 gives general requirements for access to stationary machines and guidance about the correct choice of means of access, when necessary, access to the stationary machine is not possible directly from the ground level or from a floor. This Part is applicable to permanent means of access which are a part of a stationary machine, and also to non-powered adjustable parts (e.g., foldable, slidable) and movable parts of fixed means of access. NOTE 1: “Fixed” means of access are those mounted in such a manner (for example, by screws, nuts, welding) that they can only be removed by the use of tools. This Part specifies minimum requirements that also apply when the same means of access is required as the part of the building or civil construction (e.g., working platforms, walkways, ladders) where the machine is installed, on condition that the main function of that part of the construction is to provide a means of access to the machine. NOTE 2: Where no local regulation or standards exist, this part of ISO 14122 can be used for means of access which are outside the scope of the standard. It is intended that this Part of GB/T 17888 be used with a relevant access-specific part of GB/T 17888. The GB/T 17888 series as a whole is applicable to both stationary and mobile machinery where fixed means of access are necessary. It is not applicable to powered means of access such as lifts, escalators, or other devices specially designed to lift persons between two levels. For the significant hazards covered by this Part, see Clause 4.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 17888.1-2020 be delivered?Answer: The full copy PDF of English version of GB/T 17888.1-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 17888.1-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 17888.1-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 17888.1-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 17888.1-2020?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 17888.1-2020 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 17888.1-2020?A step-by-step guide to download PDF of GB/T 17888.1-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 17888.1-2020". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
