GB/T 15008-2025 (GB/T 15008-2020) PDF EnglishUS$185.00 · In stock · Download in 9 seconds
GB/T 15008-2020: Welded Nickel-Iron-Chromium Alloy Pipes for Fluid Service Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 15008: Historical versions
Similar standardsGB/T 15008-2020: Welded Nickel-Iron-Chromium Alloy Pipes for Fluid Service---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT15008-2020NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.140.60 H 59 Replacing GB/T 15008-2008 Corrosion-Resistant Alloy Bars Issued on: MARCH 31, 2020 Implemented on: OCTOBER 01, 2020 Issued by. State Administration for Market Regulation; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative References ... 5 3 Classification ... 8 4 Order Content ... 8 5 Size, Shape and Weight ... 9 6 Technical Requirements ... 9 7 Test Methods ... 16 8 Inspection Rules ... 17 9 Packaging, Marking and Quality Certificates ... 17 Appendix A (Informative) Comparison of Domestic and Foreign Corrosion- Resistant Designations ... 18 Corrosion-Resistant Alloy Bars1 ScopeThis Standard specifies the classification, order content, size, shape, weight, technical requirements, test methods, inspection rules, packaging, marks and quality certificates of corrosion-resistant alloy bars. This Standard is applicable to iron-nickel-based, nickel-based, and nickel-copper- based hot-rolled bars (hereinafter referred to as bars) with a nominal diameter no greater than 150mm used in corrosive media.2 Normative ReferencesThe following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this document. GB/T 223.5 Steel and Iron - Determination of Acid-Soluble Silicon and Total Silicon Content - Reduced Molybdosilicate Spectrophotometric Method GB/T 223.8 Methods for Chemical Analysis of Iron, Steel and Alloy－The Sodium Fluoride Separation-EDTA Titration Method for the Determination of Aluminum Content GB/T 223.9 Iron Steel and Alloy - Determination of Aluminum Content – Chrome Azurol S Photometric Method GB/T 223.11 Iron, Steel and Alloy - Determination of Chromium Content - Visual Titration or Potentiometric Titration Method GB/T 223.14 Methods for Chemical Analysis of Iron, Steel and Alloy - The N- Benzoy-N-Phenylhydroxylamine Extraction Photometric Method for the Determination of Vanadium Content GB/T 223.17 Methods for Chemical Analysis of Iron, Steel and Alloy – The Diantipyrylmethane Photometric Method for the Determination of Titanium Content GB/T 223.18 Methods for Chemical Analysis of Iron, Steel and Alloy - The Sodium Thiosulfate Separation Iodimetric Method for the Determination of Copper Content GB/T 223.22 Methods for Chemical Analysis of Iron, Steel and Alloy - The Nitroso- R-Salt Spectrophotometric Method for the Determination of Cobalt Content GB/T 223.25 Methods for Chemical Analysis of Iron, Steel and Alloy - The Dimethylglyoxime Gravimetric Method for the Determination of Nickel Content GB/T 223.28 Methods for Chemical Analysis of Iron, Steel and Alloy - The α- Benzoinoxime Gravimetric Method for the Determination of Molybdenum Content GB/T 223.38 Methods for Chemical Analysis of Iron, Steel and Alloy - The Anion- Exchange Separation-Gravimetric Method for the Determination of Niobium Content GB/T 223.40 Iron, Steel and Alloy - Determination of Niobium Content by the Sulphochlorophenol S Spectrophotometric Method GB/T 223.42 Methods for Chemical Analysis of Iron, Steel and Alloy - The Anion- Exchange Separation-Bromopyrogallol Red Photometric Method for the Determination of Tantalum Content GB/T 223.43 Iron Steel and Alloy - Determination of Tungsten Content - Gravimetric Method and Spectrophotometric Method GB/T 223.62 Methods for Chemical Analysis of Iron, Steel and Alloy - The Butyl Acetate Extraction Photometric Method for the Determination of Phosphorus Content GB/T 223.63 Methods for Chemical Analysis of Iron, Steel and Alloy - The Sodium (Potassium) Periodate Photometric Method for the Determination of Manganese Content GB/T 223.73 Iron Steel and Alloy - Determination of Iron Contents - Titanium Trichloride-Potassium Dichromate Titration Method GB/T 223.75 Iron Steel and Alloy - Determination of Boron Content - Methanol Distillation-Curcumin Photometric Method GB/T 223.79 Iron and Steel - Determination of Multi-Element Contents - X-Ray Fluorescence Spectrometry (Routine Method) GB/T 223.85 Steel and Iron - Determination of Sulfur Content - Infrared Absorption Method after Combustion in an Induction Furnace GB/T 223.86 Steel and Iron - Determination of Total Carbon Content - Infrared Absorption Method after Combustion in an Induction Furnace GB/T 228.1 Metallic Materials - Tensile Testing - Part 1. Method of Test at Room YS/T 325.2 Methods for Chemical Analysis of Nickel-Copper Alloy - Part 2. Determination of Copper Content - Electrolysis Weight Method3 Classification3.1 Corrosion-resistant alloys are classified as follows. a) An iron-nickel-based alloy with nickel content of 30% to 50%, and the sum of nickel content and iron content of no less than 60%; b) Nickel-based alloys with nickel content of no less than 50%; c) Nickel-copper alloy with nickel content of no less than 50%, and a sum of nickel content and copper content of no less than 90%. 3.2 Bars are divided into the following two categories according to the used processing methods. a) Steel for pressure processing - UP; b) Steel for cutting – UC. The used processing method of the bar material shall be specified in the contract; if not specified, it shall be the steel for cutting processing.4 Order ContentThe contract or order placed according to this Standard shall include the following. a) The number of this Standard; b) Product name; c) Designation (or unified digital code); d) The delivered weight (or quantity); e) specifications; f) Processing method (if not specified, as per cutting steel); g) Smelting method (see 6.2); h) Delivery status; i) Special requirements (see 6.8). 6.2 Smelting method Unless otherwise specified in the contract, the smelting method shall be chosen by the supplier. 6.3 Delivery status Bars shall be delivered in hot-rolled or solid-solution status; or delivered in peeling, turning, polishing status after hot-rolled or solid-solution. The specific delivery status is indicated in the contract. 6.4 Mechanical properties 6.4.1 For the bars delivered in the hot-rolled state, the mechanical properties of the sample blank after solution treatment shall comply with the provisions of Table 2. 6.4.2 For the bars delivered in solution treatment state, cut samples from the delivered bars for inspection; the mechanical properties indicators shall conform to the provisions of Tables 2 and 3. But for bars with a diameter greater than 80mm, the mechanical properties indicators are determined through negotiation between the supplier and the purchaser. 6.4.3 For aging-strengthened alloys, cut the sample blank on the bar in the delivery state; and the mechanical properties after aging treatment shall conform to the provisions of Table 3. NS4301's high-temperature endurance performance shall conform to the provisions of Table 4. 6.4.4 The diameter of the sample blank is 25mm. When the diameter of the bar is below 25mm, conduct the solution treatment on the bars with the original diameter to make a sample for inspection. 6.4.5 The performance indicators in Table 2 are applicable to bars with a diameter no greater than 80mm. Bars with a diameter greater than 80mm are allowed to be rolled (forged) to 80mm for sampling and inspection; their performance indicators shall conform to the provisions of Table 2. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. |
