GB/T 1479.1-2011 PDF EnglishUS$170.00 · In stock · Download in 9 seconds
GB/T 1479.1-2011: Metallic powders -- Determination of apparent density -- Part 1: Funnel method Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 1479.1: Historical versions
Similar standardsGB/T 1479.1-2011: Metallic powders -- Determination of apparent density -- Part 1: Funnel method---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT1479.1-2011GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.160 H 16 GB/T 1479.1-2011 / ISO 3923-1:2008 Replacing GB/T 1479-1984 Metallic powders - Determination of apparent density - Part 1: Funnel method (ISO 3923-1:2008, IDT) ISSUED ON: MAY 12, 2011 IMPLEMENTED ON: FEBRUARY 1, 2012 Issued by: General Administration of Quality Supervision, Inspection and Quarantine of PRC; Standardization Administration of PRC. Table of ContentsForeword ... 3 1 Scope ... 5 2 Normative references ... 5 3 Principles ... 5 4 Symbols and definitions ... 5 5 Instruments ... 6 6 Samples ... 6 7 Steps ... 7 8 Presentation of results ... 7 9 Precision ... 7 10 Inspection report ... 8 Metallic powders - Determination of apparent density - Part 1: Funnel method1 ScopeThis part of GB/T 1479 specifies the method for measuring the apparent density of metal powders with a funnel under standard conditions. This part applies to metal powders that can flow freely through a funnel with a pore diameter of 2.5 mm. If the powder is difficult to pass through a pore with a diameter of 2.5 mm but can flow freely through a 5.0 mm pore, this method can also be used. Part 2 of this standard (see GB/T 1479.2) specifies the apparent density measuring method for powders that cannot pass through a 5.0 mm pore.2 Normative referencesThe following documents are essential to the application of this document. For the dated referenced documents, only the versions with the indicated dates are applicable to this document; for the undated referenced documents, only the latest versions (including all the amendments) are applicable to this document. GB/T 1479.2 Metallic powders - Determination of apparent density - Part 2: Scott volumeter method (ISO 3923-2:1981, IDT)3 PrinciplesThis part describes the measurement of the mass of the powder that in a loose condition completely fills a measuring cup with a known volume. The funnel is placed at a certain distance above the measuring cup, and the powder falls freely from the funnel into the measuring cup to obtain the loose state.4 Symbols and definitionsThe symbols and definitions involved in this standard are shown in Table 1. powder shall be dried. However, if the powder is easy to oxidize, it shall be dried under the protection of a vacuum or inert atmosphere. If the powder contains volatile substances, drying is not allowed.7 Steps7.1 Pour the powder into a funnel with a pore diameter of 2.5 mm and let the powder flow directly into the measuring cup from the small hole until the measuring cup is completely filled and the powder overflows. Level the powder with a non-magnetic straight edge, but do not compress the powder, and take care not to shake and vibrate the measuring cup. 7.2 If the powder cannot flow through the funnel, a funnel with the 5 mm pore shall be selected. If the powder still cannot flow through, it is allowed to poke the powder once from the top of the funnel with a metal wire with a diameter of 1 mm; however, take care that the metal wire cannot enter into the measuring cup. 7.3 After leveling the powder, tap the measuring cup to settle the powder, so as to avoid the powder overflowing during the movement and ensure that there is no powder sticking to the external surface of the cup. 7.4 Measure the mass of the powder, and the result shall be accurate to 0.01 g. 7.5 Take the arithmetic mean of three determination results as the final result.8 Presentation of resultsThe apparent density is calculated by the following formula: Take the arithmetic mean of the three determination results as the final result, accurate to 0.01 g/cm3. When the difference between the three determination results exceeds 1% of the mean, the maximum and minimum values shall also be reported with the final result.9 Precision9.1 Repeatability The same operator carries out two determinations with the same instrument and the same batch of powder; if at a 95% confidence level, the difference between the two determination results exceeds 0.03 g/cm3, the results are not credible. 9.2 Reproducibility The same batch of powder is tested in two different laboratories; if at a 95% confidence level, the difference between the determination results exceeds 0.05 g/cm3, the results are not credible.10 Inspection reportThe inspection report shall include the following contents: a) the standard number; b) the detailed description required for the qualification of the sample; c) If the powder is dried, the drying process shall be indicated; d) The nominal size of the pore diameter shall be indicated; if a metal wire is used, it shall be indicated; e) the results obtained; f) all other operations that are not specified in this part or optional; g) any factors that may have affected the results. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 1479.1-2011 be delivered?Answer: The full copy PDF of English version of GB/T 1479.1-2011 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 1479.1-2011_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1479.1-2011_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 1479.1-2011 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 1479.1-2011?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 1479.1-2011 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 1479.1-2011?A step-by-step guide to download PDF of GB/T 1479.1-2011_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 1479.1-2011". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
