GB/T 14202-1993 PDF EnglishUS$165.00 · In stock · Download in 9 seconds
GB/T 14202-1993: Iron ores (sinter and pellets). Determination of bulk density Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure
Similar standardsGB/T 14202-1993: Iron ores (sinter and pellets). Determination of bulk density---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT14202-1993GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA UDC 622.341 H 21 Iron Ores (Sinter and Pellets) - Determination of Bulk Density ISSUED ON: FEBRUARY 22, 1993 IMPLEMENTED ON: OCTOBER 01, 1993 Issued by: State Bureau of Technical Supervision Table of Contents1 Theme Contents and Applicable Scope ... 3 2 Normative Reference ... 3 3 Definitions ... 3 4 Test Device ... 4 5 Specimen ... 5 6 Test Procedure ... 5 7 Expression of Results ... 6 8 Test Report ... 7 Additional Information: ... 8 Iron Ores (Sinter and Pellets) - Determination of Bulk Density This Standard refers to and adopts the following international standards, such as ISO/DIS 3852-1987 Iron Ores - Determination of Bulk Density, ISO 3081-1986 Iron Ores – Increment Sampling – Manual Method, ISO 3082-1987 Iron Ores – Sampling and Sample Preparation Procedures – Mechanical Method, ISO 3087-1987 Iron Ores – Determination of Moisture Content of a Lot, and ISO 4701-1985 Iron Ores – Determination of Size Distribution by Sieving.1 Theme Contents and Applicable ScopeThis Standard specifies two measurement methods to determine the bulk density of natural and artificial iron ores. Method-1 is suitable for iron ore with a maximum particle size of 40.0 mm or less. Method-2 is applicable to iron ores with any maximum particle size. NOTE: The bulk density measured here does not necessarily represent the actual bulk density of natural or artificial ores in a compact state or in a stacked state.2 Normative ReferenceGB 2007 General Rules for the Sampling and Sample Preparation of Minerals in Bulk GB 10122 Iron Ores (Sinter and Pellets)－Sampling and Sample Preparation for Physical Testing3 Definitions3.1 Maximum particle size The particle size is expressed by the sieve size (mm); when the residual amount on the sieve is about 5% (mass percentage) of the total sieved ore, then the sieve size of the sieve grade shall be the maximum particle size. 3.2 Bulk density5 SpecimenThe specimen shall be representative and consistent with the procedures agreed between the supplier and the purchaser. 5.1 The number of specimens shall guarantee the amount of three bulk density tests; that is, the mass of three times the volume of the container with some surplus. In addition, there are specimens for measuring the supplying moisture and particle size; these two factors are the main factors affecting bulk density. 5.2 In the case of Method-1 with a volume of 0.05m3, the smallest sample is 600kg; of which three 150kg are used for bulk density test; and the other 150kg specimen is used for measuring moisture and particle size distribution. 5.3 In the case of Method-2, the minimum specimen weight is 35t; and the recommended quantity is 50t. Depending on the type and composition of iron ore, the volume of a 30t specimen is about 14~24m3.6 Test ProcedureNo matter which of the two methods is used in the bulk density test, double specimens (that is, two tests) must be prepared; meanwhile, the ore moisture and particle size distribution must be determined in accordance with the relevant provisions of GB 2007 and other standards. 6.1 Method-1 The test may use the delivered sample, or the naturally dried specimen, or the oven- dried specimen. The oven-dried specimen needs to be dried to constant weight at 105±5 °C. Dry specimens need to be cooled to room temperature before testing. 6.1.1 Weigh the dry container (4.1.1), write down its mass as m0; weigh and accurate to 0.2kg. 6.1.2 Fill the container with the delivered specimen, the naturally dried specimen or the oven-dried specimen. When loading, use the No.50 sampling shovel for the volume of 0.05m3, and use the No.10 sampling shovel (4.1.4) for the volume of 0.01m3. The discharge height (the height from the material surface in the container) is kept at about 50mm. Care should be taken during loading and unloading to avoid material segregation. When the material is full and there is overflow, use a ruler to smooth the material surface. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 14202-1993 be delivered?Answer: The full copy PDF of English version of GB/T 14202-1993 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 14202-1993_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 14202-1993_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 14202-1993 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 14202-1993?A step-by-step guide to download PDF of GB/T 14202-1993_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 14202-1993". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
