GB/T 7251.1-2023 PDF EnglishUS$1880.00 · In stock · Download in 9 seconds
GB/T 7251.1-2023: Low-voltage switchgear and controlgear assemblies - Part 1: General rules Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 7251.1: Historical versions
Similar standardsGB/T 7251.1-2023: Low-voltage switchgear and controlgear assemblies - Part 1: General rules---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT7251.1-2023GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 29.130.20 CCS K 31 GB/T 7251.1-2023 / IEC 61439-1.2020 Replacing GB/T 7251.1-2013 Low-Voltage Switchgear and Controlgear Assemblies – Part 1.General Rules (IEC 61349-1.2020, IDT) Issued on: AUGUST 6, 2023 Implemented on: MARCH 1, 2024 Issued by. State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 7 Introduction... 11 1 Scope... 13 2 Normative References... 14 3 Terms and Definitions... 19 4 Symbols and Abbreviations... 40 5 Interface Characteristics... 42 5.1 General... 42 5.2 Voltage ratings... 42 5.2.1 Rated voltage (Un) (of the assembly)... 42 5.2.2 Rated operational voltage (Ue) (of a circuit of an assembly)... 42 5.2.3 Rated insulation voltage (Ui) (of a circuit of an assembly)... 42 5.2.4 Rated impulse withstand voltage (Uimp) (of the assembly)... 42 5.3 Current ratings... 43 5.3.1 Rated current of an assembly (InA)... 43 5.3.2 Rated current of a main outgoing circuit (Inc)... 43 5.3.3 Group rated current of a main circuit (Ing)... 43 5.3.4 Rated peak withstand current (Ipk)... 44 5.3.5 Rated short-time withstand current (Icw) (of a main circuit of an assembly)... 44 5.3.6 Rated conditional short-circuit current (Icc) (of an assembly or a circuit of an assembly)... 45 5.4 Rated diversity factor (RDF)... 45 5.5 Rated frequency (fn)... 45 5.6 Other characteristics... 46 6 Information... 46 6.1 Assembly designation marking... 46 6.2 Documentation... 47 6.2.1 Information relating to the assembly... 47 6.2.2 Instructions for handling, installation, operation and maintenance... 47 6.3 Device and/or component identification... 48 7 Service Conditions... 48 7.1 Normal service conditions... 48 7.1.1 Climatic conditions... 48 7.1.2 Pollution degree... 49 7.2 Special service conditions... 49 7.3 Conditions during transport, storage and installation... 50IntroductionGB/T 7251 adopts IEC international standards to meet the needs of international trade, technical and economic exchanges. The purpose of this Document is to harmonize as far as practicable all rules and requirements of a general nature applicable to low-voltage switchgear and controlgear assemblies, in order to obtain uniformity of requirements and verification for assemblies and to avoid the need for verification in other standards. All those requirements for the various assembly standards which can be considered as general have therefore been gathered in this Document together with specific subjects of wide interest and application, e.g. temperature-rise, dielectric properties, etc. For each type of low-voltage switchgear and controlgear assembly, only two main standards are necessary to determine all requirements and the corresponding methods of verification. – the basic standard, (this Document) referred to as GB/T 7251.1 in the specific standards, covering the various types of low-voltage switchgear and controlgear assemblies; – the specific assembly standard hereinafter also referred to as the relevant assembly standard. If the basic rules are not applicable, the specific complete equipment standard does not require it, so it is not necessary to propose it; if the basic rules are not sufficient for special occasions, the specific complete equipment standard can add requirements; unless there are reliable and sufficient technical reasons, it is not allowed to violate the basic rules in the specific complete equipment standard. In this Document, if another clause is cross-referenced, the reference applies to the clause revised by the specific complete equipment standard, if applicable. Appendix N listed the "List of Notes of Certain Countries" that are different from this Document. The other parts of GB/T 7251 are product standards, and the product standards quote a large number of technical requirements and test methods specified in this Document, so the other parts are used in conjunction with this Document. GB/T 7251 is intended to consist of nine parts. --- Part 1.General rules. It aims to specify common requirements for various types of complete equipment standards. --- Part 2.Power switchgear and controlgear assemblies. It aims to specify specific requirements and verification methods for power switchgear and controlgear Low-Voltage Switchgear and Controlgear Assemblies – Part 1.General Rules1 ScopeThis Document lays down the general definitions and service conditions, construction requirements, technical characteristics and verification requirements for low-voltage switchgear and controlgear assemblies. NOTE. Throughout this document, the term assembly(s) (see 3.1.1) is used for a low-voltage switchgear and controlgear assembly(s). For the purpose of determining assembly conformity, the requirements of the relevant part of the IEC 61439 series, Part 2 onwards, apply together with the cited requirements of this document. For assemblies not covered by IEC 61439-3 onward, IEC 61439-2 applies. This document applies to assemblies only when required by the relevant assembly standard as follows. – assemblies for which the rated voltage does not exceed 1 000 V AC or 1 500 V DC; – assemblies designed for a nominal frequency of the incoming supply or supplies not exceeding 1 000 Hz; – assemblies intended for indoor and outdoor applications; – stationary or movable assemblies with or without an enclosure; – assemblies intended for use in connection with the generation, transmission, distribution and conversion of electric energy, and for the control of electrical energy consuming equipment. This document does not apply to individual devices and self-contained components such as motor starters, fuse switches, power electronic converter systems and equipment (PECS), switch mode power supplies (SMPS), uninterruptable power supplies (UPS), basic drive modules (BDM), complete drive modules (CDM), adjustable speed power drives systems (PDS), and other electronic equipment which comply with their relevant product standards. This document describes the integration of devices and self-contained components into an assembly or into an empty enclosure forming an assembly. For some applications involving, for example, explosive atmospheres, functional safety, there can be a need to comply with the requirements of other standards or legislation in addition to those specified in the IEC 61439 (all parts).2 Normative ReferencesThe provisions in following documents become the essential provisions of this Document through reference in this Document. For the dated documents, only the versions with the dates indicated are applicable to this Document; for the undated documents, only the latest version (including all the amendments) is applicable to this Document. GB/T 2423.2-2008 Environmental testing - Part 2.Test methods - Tests B. Dry heat (IEC 60068-2-2.2007, IDT) GB/T 2423.4-2008 Environmental testing for electric and electronic products - Part 2.Test method - Test Db. Damp heat, cyclic (12h+12h cycle) (IEC 60068-2-30.2005, IDT) GB/T 2423.17-2008 Environmental testing for electric and electronic products - Part 2. Test method - Test Ka. Salt mist (IEC 60068-2-11.1981, IDT) GB/T 4025-2010 Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators (IEC 60073.2002, IDT) GB/T 4026-2019 Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors (IEC 60445.2017, IDT) GB/T 4205-2010 Basic and safety principles for man-machine interface (MMI), marking and identification - Actuating principles (IEC 60447.2004, IDT) GB/T 5094.1-2018 Industrial systems, installations and equipment and industrial products -Structuring principles and reference designations - Part 1.Basic rules (IEC 81346-1.2009, IDT) GB/T 5169.10-2017 Fire hazard testing for electric and electronic products - Part 10. Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure (IEC 60695-2-10.2013, IDT) GB/T 5169.11-2017 Fire hazard testing for electric and electronic products - Part 11. Glowing/hot-wire based test methods - Glow-wire flammability test method for end- products (GWEPT) (IEC 60695-2-11.2014, IDT) GB/T 11021-2014 Electrical Insulation - Thermal Evaluation and Designation (IEC 60085.2007, IDT) GB/T 16895.6-2014 Electric installations of buildings - Part 5-52.Selection and erection disturbance characteristics – Limits and methods of measurement3 Terms and DefinitionsFor the purposes of this document, the following terms and definitions apply. 3.1 General terms 3.1.1 Low-voltage switchgear and controlgear assembly; Assembly Combination of one or more low-voltage switching devices together with associated control, measuring, signaling, protective, regulating equipment, with all the internal electrical and mechanical interconnections and structural parts, as defined by the original manufacturer, which can be assembled in accordance with the original manufacturer’s instructions. 3.1.2 Assembly system Full range of mechanical and electrical components (enclosures, busbars, functional units, auxiliary circuits and associated controls, etc.), as defined by the original manufacturer, which can be assembled in accordance with the original manufacturer’s instructions in order to produce various assemblies. Organization taking the responsibility for the completed assembly. NOTE. The assembly manufacturer can be the same or a different organization to the original manufacturer. 3.11 User Party who will specify, purchase, use and/or operate the assembly, or someone acting on their behalf.4 Symbols and AbbreviationsThe following symbols and abbreviations apply to this Document. Alphabetical list of terms with symbols and abbreviations together with the subclause where they are first used.5 Interface Characteristics5.1 General The characteristics of the assembly shall ensure compatibility with the ratings of the circuits to which they are connected plus the installation conditions and shall be declared by the assembly manufacturer using the criteria identified in 5.2 to 5.6. 5.2 Voltage ratings 5.2.1 Rated voltage (Un) (of the assembly) The rated voltage shall be at least equal to the nominal voltage of the electrical system. NOTE. For further details on nominal system voltage see IEC 60038. 5.2.2 Rated operational voltage (Ue) (of a circuit of an assembly) The rated operational voltage of any circuit shall not be less than the nominal voltage of the electrical system to which it is to be connected. If the nominal voltage is given for a three-phase system, the rated operational voltage of single- phase circuits shall not be less than the nominal voltage divided by √3. If different from the rated voltage of the assembly, the appropriate rated operational voltage of the circuit shall be stated.6 Information6.1 Assembly designation marking The assembly manufacturer shall provide each assembly with one or more labels, marked in a durable manner and located in a place such that they are visible and legible when the assembly is installed and in operation. Compliance is checked according to the test of 10.2.7 and by inspection. the designation label. 6.2 Documentation 6.2.1 Information relating to the assembly All interface characteristics according to Clause 5, where applicable, shall be provided in the assembly manufacturer’s technical documentation supplied with the assembly.7 Service Conditions7.1 Normal service conditions 7.1.1 Climatic conditions Assemblies conforming to this document are intended for use under the normal service conditions detailed in Table 15. If components, for example relays, electronic equipment, are used which are not designed for these conditions, the environment provided within the assembly shall be suitable for the components. 7.1.2 Pollution degree The pollution degree referred to in Annex C is the macro-environmental condition for which the assembly is intended. For switching devices and components inside an enclosure, the pollution degree of the environmental conditions inside the enclosure, the micro-environment, is applicable. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 7251.1-2023 be delivered?Answer: The full copy PDF of English version of GB/T 7251.1-2023 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 7251.1-2023_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 7251.1-2023_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 7251.1-2023 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 7251.1-2023?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 7251.1-2023 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 7251.1-2023?A step-by-step guide to download PDF of GB/T 7251.1-2023_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 7251.1-2023". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
