GB/T 50387-2017 (GB 50387-2006) PDF EnglishUS$85.00 · In stock · Download in 9 seconds
GB 50387-2006: Code for installation acceptance of metal mechanical hydromatic, lubricating and air-driven system equipment Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Obsolete GB 50387: Historical versions
Similar standardsGB 50387-2006: Code for installation acceptance of metal mechanical hydromatic, lubricating and air-driven system equipment---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB50387-2006 GB UDC NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA P GB 50387-2006 Code for installation acceptance of metal mechanical hydromatic, lubricating and air-driven system equipment Issued on: SEPTEMBER 6, 2006 Implemented on: APRIL 1, 2007 Issued by. Ministry of Construction of the People's Republic of China; General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China. National Standard of the People's Republic of China Code for installation acceptance of metal mechanical hydromatic, lubricating and air-driven system equipment Main drafting organization. China Metallurgical Construction Association Approval organization. The Ministry of Construction of the People's Republic of China Implementation Date. April 1, 2007 China Planning Press 2007 Beijing ForewordAccording to the relevant requirements of Document JIANBIAO [2005] No.124 issued by the Ministry of Construction - “Notice on Printing and Distributing ‘the Development and Revision Plan (the second batch) of National Engineering Construction Standards and Codes in 2005’”, this code was formulated, in combination with the characteristics of metallurgical construction, by China First Metallurgical Construction Co., Ltd. jointly with the organizations concerned, under the organization of China Metallurgical Construction Association. In the process of formulating this code, the code drafting group learnt the relevant current national laws, regulations and standards, conducted investigations and studies, summarized the experience in the construction quality acceptance of hydromatic, lubricating and air-driven system equipment in metal mechanical equipment installation engineering over the years, discussed and revised the provisions in the code repeatedly, solicited the opinions from related organizations and experts, and finalized this code through review. This code consists of eight chapters, covering General Provisions; Basic Requirements; Equipment Foundation, Anchor Bolt and Bearing Plate; Equipment and Materials in Site; Equipment Installation; Fabrication and Installation of Pipeline; Pipeline Flushing, Purging and Pressure Test; and Commissioning and Test-run, as well as six appendixes. The unit project in installation of hydromatic, lubricating and air-driven system equipment totally comprises seven sub-section projects and corresponding sub-item projects. The provisions printed in bold type in this code are mandatory ones and must be implemented strictly. This code is under the jurisdiction of, and its mandatory provisions are interpreted by the Ministry of Construction. China First Metallurgical Construction Co., Ltd. is in charge of the explanation of specific technical specifications In order to improve the quality of this code, all relevant organizations are kindly invited to summarize and accumulate actual experiences when implementing this code. Relevant comments and recommendations, whenever necessary, should be fed back to China First Metallurgical Construction Co., Ltd. (Address. No.3, Gongye Avenue, Qingshan District, Wuhan City, 430081, China; E-mail. jisc@cfmcc.com or xiaolw@cfmcc.com) for amendment in future revision. The chief drafting organization, co-drafting organization and chief drafters of this code are. Chief Formulation Organization. China First Metallurgical Construction Co., Ltd. Co-formulation Organization. Shanghai Baoye Group Construction Co., Ltd. Chief Drafters. Zhuo Guangyu, Xu Zuwen, Li Mingzhu, Wang Shiqing, Wu Gangping, Liu Shiyin, Song Zhanjiang, Liu Zhiyuan, Liu Guangqiu, Luo Jin and Zou Yichang.Table of Contents1 General Provisions... 7 2 Basic Requirements... 8 3 Equipment Foundation, Anchor Bolt and Bearing Plate... 12 3.1 General Requirements... 12 3.2 Equipment Foundation... 12 3.3 Anchor Bolt... 12 3.4 Bearing Plate... 13 4 Equipment and Materials in Site... 14 4.1 General Requirements... 14 4.2 Equipment... 14 4.3 Raw Materials... 14 5 Installation of Equipment... 15 5.1 General Requirements... 15 5.2 Installation of Oil Tank... 15 5.3 Installation of Cooler and Steam Heater... 15 5.4 Installation of Filter... 16 5.5 Installation of Energy Accumulator... 16 5.6 Installation of Pump... 16 5.7 Installation of Complete Set of Hydraulic (Lubrication) Station... 17 5.8 Installation of Brackets for Hydraulic (Air) Valve and Control Valve... 17 5.9 Installation of Oil Purifier... 18 5.10 Installation of Oil Feeder and Distributor... 18 5.11 Installation of Water-separating Gas Filter, Atomized (Oil Gas) Lubricator and Control Valve... 18 6 Fabrication and Installation of Pipeline... 19 6.1 General Requirements... 19 6.2 Pipeline Welding... 19 6.3 Pipeline Pickling... 20 6.4 Pipeline Fabrication... 20 6.5 Pipeline Installation... 21 7 Pipeline Flushing, Purging and Pressure Test... 24 7.1 General Requirements... 24 7.2 Pipeline Flushing... 24 7.3 Pipeline Purging... 25 7.4 Pressure Test for Hydromatic and Lubricant Pipeline Systems... 25 7.5 Pressure Test for Grease Pipeline System... 25 7.6 Pressure Test for Air-driven Pipeline System... 26 8.1 General Requirements... 27 8.2 Commissioning and Test-run of Hydromatic Equipment... 27 8.3 Commissioning and Test-run of Lubricant Equipment... 28 8.4 Commissioning and Test-run of Grease Equipment... 29 8.5 Commissioning and Test-run of Oil Fog Lubricating Equipment... 29 8.6 Commissioning and Test-run of Technological Lubricating Equipment... 30 8.7 Commissioning and Test-run of Air-driven System Equipment... 31 Appendix A Quality Acceptance Records of Sub-item Projects in Installation of Metal Mechanical Hydromatic, Lubricating and Air-driven System Equipment... 32 Appendix B Quality Acceptance Records of Sub-section Projects in Installation of Metal Mechanical Hydromatic, Lubricating and Air-driven System Equipment... 33 Appendix C Quality Acceptance Records of Unit Projects in Installation of Metal Mechanical Hydromatic, Lubricating and Air-driven System Equipment... 34 Appendix D Commissioning and Test-run Records for Metal Mechanical Hydromatic, Lubricating and Air-driven System Equipment... 37 Appendix E No-load Linkage Test-run Records for Metal Mechanical Hydromatic, Lubricating and Air-driven System Equipment... 38 Appendix F Coding of hydramatic transmission, oil solid particle contamination level (Excerpted from National Standard GB/T 14039-2002)... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. |
