GB 1886.2-2015 PDF EnglishUS$105.00 · In stock · Download in 9 seconds
GB 1886.2-2015: National Food Safety Standard - Food Additives - Sodium bicarbonate Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB 1886.2-2015: National Food Safety Standard - Food Additives - Sodium bicarbonate---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB1886.2-2015GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA National Food Safety Standard - Food Additives - Sodium Bicarbonate Issued on: SEPTEMBER 22, 2015 Implemented on: MARCH 22, 2016 Issued by. National Health and Family Planning Commission of the People’s Republic of China. Table of ContentsForeword... 3 1 Scope... 4 2 Molecular Formula and Relative Molecular Mass... 4 3 Technical Requirements... 4 Appendix A Inspection Method... 6 National Food Safety Standard - Food Additives - Sodium Bicarbonate1 ScopeThis Standard is applicable to food additives - sodium bicarbonate.2 Molecular Formula and Relative Molecular Mass2.1 Molecular Formula NaHCO3 2.2 Relative Molecular Mass 84.01 (in accordance with the international relative atomic mass in 2007)3 Technical Requirements3.1 Sensory Requirements The sensory requirements shall comply with the provisions of Table 1. 3.2 Physical and Chemical Indicators The physical and chemical indicators shall comply with the provisions of Table 2.Appendix AInspection Method A.1 Safety Tips Some of the reagents used in this test method are toxic or corrosive and shall be handled with caution. If they splash on the skin, immediately use water to rinse them. If it becomes serious, immediately seek medical treatment. A.2 General Provisions Unless otherwise specified, the reagents and water used in this Standard refer to analytically pure reagents and Grade-3 water as specified in GB/T 6682.Unless otherwise specified, the standard solutions, impurity standard solutions, preparations and products required in the test shall be prepared in accordance with the provisions of GB/T 601, GB/T 602 and GB/T 603. Unless the solvent used is specified, the solutions used in the test are aqueous solutions. A.3 Identification Test A.3.1 Identification of sodium Use hydrochloric acid to wet the platinum wire and burn it on the flame, until it becomes colorless. Then, dip a small amount of the test solution and burn it on the flame. The flame will then turn bright yellow. A.3.2 Identification of bicarbonate A.3.2.1 Take a small amount of the specimen and add hydrochloric acid solution (1+2) to generate gas. This gas is passed into calcium hydroxide solution (3 g/L) to generate a white precipitate. A.3.2.2 When magnesium sulfate solution (120 g/L) is dropwise added to the test solution, no precipitation occurs at room temperature, but a white precipitate is generated after boiling. A.4 Determination of Total Alkali Content (by NaHCO3) A.4.1 Method Summary Dissolve the specimen in water, use bromocresol green-methyl red as an indicator and use a standard hydrochloric acid titration solution to perform titration. A.4.2 Reagents and materials A.4.2.1 Standard hydrochloric acid titration solution. c(HCl) = 1 mol/L. A.4.2.2 Bromocresol green-methyl red indicator solution. A.4.3 Analytical steps Weigh-take about 2.5 g of specimen, accurate to 0.0002 g, place in a 250 mL conical flask, and add 50 mL of water to completely dissolve it. Dropwise add 10 drops of bromocresol green- methyl red indicator solution, use the standard hydrochloric acid titration solution to titrate it, until the test solution turns from green to dark red, boil for 2 minutes, cool to room temperature, and use the standard hydrochloric acid titration solution to continue titrating, until it turns dark red, which is the end point. Meanwhile, perform a blank test. The blank test shall be carried out in parallel with determination, using the same analytical steps and the same amounts of all reagents (except the standard titration solution), but no specimen is added to the blank test. A.4.4 Result calculation The mass fraction w1 of the total alkali content (by NaHCO3) is calculated in accordance with Formula (A.1). Where, c---the concentration of standard hydrochloric acid titration solution, expressed in (mol/L); V1---the volume of the standard hydrochloric acid titration solution consumed by the titration of the test solution, expressed in (mL); V0---the volume of the standard hydrochloric acid titration solution consumed by the blank test, expressed in (mL); M---the molar mass of sodium bicarbonate, expressed in (g/mol), [M(NaHCO3) = 84.01]; m---the mass of the specimen, expressed in (g); 1,000---the conversion factor. The test result shall be based on the arithmetic mean of the parallel determination results. The absolute difference between two independent determination results obtained under repeatability conditions is not greater than 0.2%. A.5 Determination of Loss on Drying A.5.1 Method summary Place the specimen in a vacuum drying oven for 4 h, then, take it out and determine its loss on drying. A.5.2 Instruments and equipment Weigh-take about 1 g of specimen, accurate to 0.01 g. Place in a 50 mL beaker and add 10 mL of water to dissolve it. There is no ammonia smell during heating to boiling. A.8 Determination of Clarity A.8.1 Method Summary At room temperature, use a quantitative amount of water to dissolve the specimen. Under the same conditions, compare it with the standard. A.8.2 Reagents and materials A.8.2.1 Hexamethylenetetramine solution. 100 g/L. Weigh-take 10.0 g 0.1 g of hexamethylenetetramine that has been dried in a silica gel dryer for 24 hours, place it in a beaker, add a small amount of water to dissolve it, transfer it all to a 100 mL volumetric flask, use water to dilute to the scale, and shake it well. A.8.2.2 Hydrazine sulfate solution. 10 g/L. Weigh-take 1.0 g 0.1 g of hydrazine sulfate that has been dried in a silica gel dryer for 24 hours, place it in a beaker, add a small amount of water to dissolve it, transfer it all to a 100 mL volumetric flask, use water to dilute to the scale, and shake it well. A.8.2.3 Standard turbidimetric solution. Use a pipette to transfer-take 25 mL of hexamethylenetetramine solution and 25 mL of hydrazine sulfate solution into a dry reagent bottle, shake it well, and leave at room temperature for 24 hours to prepare standard turbidimetric solution A. This solution is valid for 60 days. Use a pipette to transfer-take 10.0 mL of the standard turbidimetric solution A into a 1,000 mL volumetric flask, use water to dilute to the scale, and shake it well to prepare standard turbidimetric solution B. This solution is valid for 1 day. A.8.3 Analytical steps Weigh-take 1.00 g 0.01 g of specimen and place it in a 25 mL colorimetric tube. After adding water to dissolve it, use water to dilute to the scale and shake it well. After standing for 5 minutes, compare it with the standard turbidimetric solution, against a black background, and observe from above the colorimetric tube. The clarity of the test solution must not be lower than that of the standard turbidimetric solution. The standard turbidimetric solution is prepared by using a pipette to transfer-take 5.00 mL of the standard turbidimetric solution B into a 25 mL colorimetric tube, using water to dilute to the scale and shaking it well. A.9 Determination of Chloride (by Cl) A.9.1 Mercurimetry (arbitration method) A.9.1.1 Method Summary 1,000---the conversion factor. The test result shall be based on the arithmetic mean of the parallel determination results. The absolute difference between two independent determination results obtained under repeatability conditions is not greater than 0.01%. A.9.2 Visual turbidimetry A.9.2.1 Method summary Add silver nitrate solution to an acidic medium, the silver ions and chloride ions generate a white silver chloride suspension, which is compared with the standard turbidimetric solution simultaneously treated in the same mode. A.9.2.2 Reagents and materials A.9.2.2.1 95% ethanol. A.9.2.2.2 Nitric acid solution. 1 + 6. A.9.2.2.3 Silver nitrate solution. 17 g/L. A.9.2.2.4 Chloride standard solution. 1 mL of solution contains 0.10 mg of chlorine (Cl). A.9.2.3 Analytical steps Weigh-take 1.00 g 0.01 g of specimen, place it in a 50 mL beaker, add an appropriate amount of water to dissolve it, transfer it all to a 100 mL volumetric flask, use water to dilute to the scale, and shake it well. Use a pipette to transfer-take 25 mL of the test solution into a 50 mL colorimetric tube, add 1 mL of ethanol solution with a volume fraction of 95%, 3 mL of nitric acid solution and 2 mL of silver nitrate solution, use water to dilute to the scale, and gently shake it. After standing for 10 minutes, against a black background, compare it with the standard turbidimetric solution. The turbidity generated must not be darker than that of the standard turbidimetric solution. The standard turbidimetric solution is prepared by transferring 0.50 mL, 1.50 mL, 2.00 mL, 2.50 mL and 5.00 mL of chloride standard solution, and simultaneously handling it in the same mode as the specimen. A.10 Determination of Whiteness A.10.1 Instruments and equipment A.10.1.1 Whiteness meter. equipped with a standard whiteness board and working whiteness board, with a division value of 0.2. A.10.1.2 Standard whiteness board. A.10.2 Analytical steps ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 1886.2-2015 be delivered?Answer: The full copy PDF of English version of GB 1886.2-2015 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 1886.2-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB 1886.2-2015_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 1886.2-2015 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB 1886.2-2015?A step-by-step guide to download PDF of GB 1886.2-2015_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 1886.2-2015". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
