GB 17799.4-2022 PDF EnglishUS$305.00 · In stock · Download in 9 seconds
GB 17799.4-2022: Electromagnetic compatibility (EMC) - Generic standards - Part 4: Emission for industrial environments Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB 17799.4: Historical versions
Similar standardsGB 17799.4-2022: Electromagnetic compatibility (EMC) - Generic standards - Part 4: Emission for industrial environments---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB17799.4-2022 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 33.100 CCS L 06 GB 17799.4-2022 / IEC 61000-6-4.2018 Replacing GB 17799.4-2012 Electromagnetic compatibility (EMC) - Generic standards - Part 4.Emission for industrial environments (IEC 61000-6-4.2018, Electromagnetic compatibility (EMC) - Part 6-4. Generic standards - Emission standard for industrial environments, IDT) Issued on. OCTOBER 12, 2022 Implemented on. NOVEMBER 01, 2023 Issued by. State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 Introduction... 5 1 Scope... 6 2 Normative references... 6 3 Terms, definitions and abbreviations... 8 4 Test conditions... 13 5 Product documentation... 14 6 Applicability... 14 7 Uncertainty of measurement... 14 8 Compliance with this document... 15 9 Emission requirements... 15 Annex A (Informative) Testing of DC powered systems... 21 Annex B (Informative) Further information on measurements using a FAR... 23 Bibliography... 31ForewordThis document was drafted in accordance with the rules provided in GB/T 1.1-2020 Directives for standardization - Part 1.Rules for the structure and drafting of standardizing documents. This document is part 4 of Electromagnetic compatibility (EMC) - Generic standards. The following parts have been in released for Electromagnetic compatibility (EMC) - Generic standards. -- Immunity for residential, commercial and light-industrial environments (GB/T 17799.1); -- Immunity for industrial environments (GB/T 17799.2); -- Emission standard for residential, commercial and light-industrial environments (GB 17799.3); -- Emission for industrial environments (GB 17799.4); -- HEMP immunity for indoor equipment (GB/T 17799.5); -- Immunity for power station and substation environments (GB/Z 17799.6). This document replaces GB 17799.4-2012 Electromagnetic compatibility (EMC) - Generic standards - Emission standard for industrial environments. Compared with GB 17799.4-2012, in addition to structural adjustments and editorial changes, the main technical changes are as follows. a) Add the definition of different EUT test arrangements (see Clause 4); b) Add the definition of which average detector is used for emission measurements at frequencies above 1 GHz and that results using a peak detector are acceptable for all measurements (see Clause 9); c) Add requirements on DC ports (see Annex A); d) Add radiated polarity specific emission limits within a FAR (see Annex B). This document is identical to IEC 61000-6-4.2018 Electromagnetic compatibility (EMC) - Part 6-4.Generic standards - Emission standard for industrial environments. The following minimal editorial changes are made to this document. -- Change the standard name to Electromagnetic compatibility (EMC) - Generic standards - Part 4.Emission for industrial environments, to be consistent with the technical standard system in China; Please note that some of the contents of this document may involve patents. The issuing organization of this document is not responsible for identifying patents. This document shall be under the jurisdiction of Standardization Administration of the People’s Republic of China. The previous versions of this document and the documents which are replaced by this document are as follows. -- It was first published as GB 17799.4-2001 in 2001 and revised for the first time in 2012; -- This is the second revision.1 ScopeThis document for emission requirements applies to electrical and electronic equipment intended for use within the environment existing at industrial (see 3.1.12) locations. This document does not apply to equipment that fall within the scope of GB 17799.3. The environments encompassed by this document cover both indoor and outdoor locations.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the version corresponding to that date is applicable to this document; for undated references, the latest version (including all amendments) is applicable to this document. GB 4824-2019, Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement (CISPR 11.2015, IDT)3 Terms, definitions and abbreviationsPhysical boundary of the equipment which electromagnetic fields may radiate through or impinge on.4 Test conditionsThe equipment under test (EUT) shall be tested in the operating mode producing the largest emission in the frequency band being measured, consistent with normal applications. The configuration of the test sample shall be varied to achieve maximum emission consistent with typical applications and installation practice. Pre-testing may be used to reduce test time.5 Product documentationThe purchaser/user/installer shall be informed within the product documentation if special measures have to be taken to achieve compliance. One example, would be the need to use shielded or special cables.6 ApplicabilityThe application of measurements for emission(s) depends on the particular equipment, its configuration, its ports, its technology and its operating conditions. Measurements shall be applied to the relevant ports of the equipment according to the requirements defined in Table 3 ~ Table 5.Measurements shall only be carried out where the relevant ports exist.7 Uncertainty of measurementWhere guidance for the calculation of the instrumentation uncertainty of a measurement is specified in GB/T 6113.402-2018 this shall be followed, and for these measurements the determination of compliance with the limits in this document shall take into consideration the measurement instrumentation uncertainty in accordance with GB/T 6113.402-2018.8 Compliance with this documentWhere this document gives options for testing particular requirements with a choice of test methods, compliance can be shown against any of the relevant test methods, using the specific limits with the restrictions provided in the relevant tables clauses.9 Emission requirementsThe emission requirements for equipment covered by this document are given on a port by port basis and defined in Table 3 ~ Table 5.Annex A is provided for information purposes only and lists proposed limits for DC power ports. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 17799.4-2022 be delivered?Answer: The full copy PDF of English version of GB 17799.4-2022 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 17799.4-2022_English with my colleagues?Answer: Yes. The purchased PDF of GB 17799.4-2022_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 17799.4-2022 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB 17799.4-2022?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB 17799.4-2022 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB 17799.4-2022?A step-by-step guide to download PDF of GB 17799.4-2022_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 17799.4-2022". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
