Chinese Standards Shop Partner of Google-Books Database: 169759 (Nov 17, 2019)
 HOME   Quotation   Tax   Examples Standard-List   Contact-Us   View-Cart
  

HG/T 2502-1993

Chinese Standard: 'HG/T 2502-1993'
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)StatusRelated Standard
HG/T 2502-1993English95 Add to Cart 0--15 minutes. Auto immediate delivery. 5201 Grease Valid HG/T 2502-1993

 HG/T 2502-1993 -- Click to view the ACTUAL PDF of this standard (Auto-delivered in 0~10 minutes) In 0~10 minutes time, full copy of this English-PDF will be auto-immediately delivered to your email. See samples for translation quality.  
Detail Information of HG/T 2502-1993; HG/T2502-1993; HGT 2502-1993; HGT2502-1993
Description (Translated English): (5201 Grease)
Sector / Industry: Chemical Industry Industry Standard (Recommended)
Classification of Chinese Standard: G17
Classification of International Standard: 71.080.70
Word Count Estimation: 9,000
Date of Issue: 8/9/1993
Date of Implementation: 1/7/1994
Older Standard (superseded by this standard): HG 2-1491-1983
Adopted Standard: MIL-S-8660C, NEQ
Drafting Organization: Shanghai Resin Factory
Administrative Organization: National Standardization Technical Committee plastic resin plastic products branch
Regulation (derived from): Ministry of Industry and Information Technology Notice No. 8, 2013
Summary: This standard specifies the technical requirements for 5201 grease, test methods, inspection rules and signs, packaging, transportation and storage requirements. This standard applies to simethicone was made ??of fumed silica thickened grease.

HG/T 2502-93
HG
CHEMICAL INDUSTRY STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
5201 Silicone Grease
5201 硅脂
ISSUED ON. SEPTEMBER 8, 1993
IMPLEMENTED ON. JULY 1, 1994
Issued by. Ministry of Chemical Industry of PRC
Table of Contents
1 Subject content and application scope ... 3 
2 Normative references ... 3 
3 Designation ... 3 
4 Technical requirements ... 4 
5 Test methods ... 5 
6 Inspection rules ... 11 
7 Marking, packaging, transportation and storage ... 12 
Additional information ... 13 
5201 Silicone Grease
1 Subject content and application scope
This Standard specifies the technical requirements, test methods, inspection rules and
the requirements for marking, packaging, transportation and storage for 5201 silicone
grease.
This Standard applies to silicone grease made from dimethyl silicon oil by densifying
fumed silica.
2 Normative references
GB 269, Lubricating grease – Determination of cone penetration
GB 1408, Test methods at power frequencies for electric strength of solid insulating
materials
GB 1409, Methods for the determination of the permittivity and dielectric dissipation
factor of solid electrical insulating materials at power, audio and radio frequencies
including metre wavelengths
GB 1410, Methods of test for volume resistivity and surface resistivity of solid
electrical insulating materials
GB/T 6678, General principles for sampling chemical products
GB/T 6679, General rules for sampling solid chemical products
GB 10580, Standard conditions for use prior to and during the testing of solid
electrical insulating materials
SY 2710, Corrosion test of lubricating grease
3 Designation
3.1 The designation of this product consists of secondary processing type code,
silicone oil code, group code and sequence number, as shown in Figure 1.
5 Test methods
5.1 Determination of appearance
Open the package and conduct visual inspection under natural lighting.
5.2 Determination of cone penetration
5.2.1 Determination of non-working cone penetration
Conduct the determination in accordance with the method specified in paragraphs 2 to
4 in method A of the 1st section, GB 269, including.
a. the gas is exhausted for 1 h under the residual pressure not greater than 400 Pa;
and
b. the test temperature is 25 ± 5˚C.
The results shall be rounded off to 3 significant figures.
5.2.2 Determination of working cone penetration
Conduct the determination in accordance with the method specified in paragraphs 2 to
3 and paragraph 5 in method A of the 1st section of GB 269, including the exhaust
conditions and test conditions for the specimens the same as 5.2.1.
The results shall be rounded off to 3 significant figures.
5.3 Determination of oil separation and volatile content
5.3.1 Apparatus
5.3.1.1 Electric constant-temperature drying oven. the maximum working
temperature 300˚C; the temperature control accuracy ± 2˚C.
5.3.1.2 Analytical balance. the maximum load 200 g; the sensitivity 0.1 mg.
5.3.1.3 Desiccator. containing allochroic silicagel or anhydrous calcium chloride
desiccant.
5.3.1.4 Steel mesh oil separation measuring equipment. as shown in Figure 2.
5.7.1.3 Screen. stainless steel screen, mesh size 1.0 to 1.3 mm.
5.7.1.4 Tripod. made of iron.
5.7.2 Test procedure
Weigh approximately 10 g of the specimen to place on the stainless-steel screen,
whose coverage is a circle with a diameter of 2.5 cm. Place the screen on the tripod;
heat underneath it cautiously with a combustion lamp not to let the flame run to the
above of the screen. When the specimen starts to decompose or becomes volatile,
use a second combustion lamp to ignite the gas discharged. When the combustion
lamps are both withdrawn, observe whether the flame extinguishes immediately. If it
does not extinguish immediately, the specimen is not self-extinguishing, and stop the
test. If it extinguishes, continue to heat until the specimen is red hot, and ignite once
again. if it still extinguishes, the specimen is self-extinguishing, or else, it is not self-
extinguishing, and then stop the test.
5.7.3 Judgment of test results
Conduct 3 tests in parallel and take two results identical as the final test result.
5.8 Determination of corrosivity
Conduct the determination in accordance with the method specified in SY 2710,
including.
the material of the sheet metal is steel no. 45 of the dimensions 50 mm × 50 mm × (3.5
to 5) mm.
5.9 Determination of waterproofing
5.9.1 Reagent and solution
Cobalt chloride water solution. containing 25 g of cobalt chloride per 100 mL of the
solution.
5.9.2 Apparatus and materials
5.9.2.1 Electric constant-temperature drying oven. the maximum working
temperature 150˚C and the temperature control accuracy ± 1˚C.
5.9.2.2 Oxidation vessel. glass made, the diameter 30 ± 2 mm and the height 12 ± 1
mm.
5.9.2.3 Water bath.
5.9.2.4 Scraper.
5.9.2.5 Filter paper. Ø 25 ± 1 mm.
with this Standard; and if a re-inspection is necessary, it shall be conducted within 6
weeks after receiving the products.
6.7 When there is any dispute between the supplier and the purchaser on the product
quality, it shall be settled by both sides through consultation or a statutory quality
inspection department through arbitration.
7 Marking, packaging, transportation and storage
7.1 Marking
Each package of the products shall be marked legibly and indelibly, indicating product
name, type, grade, batch number, net weight, manufacturing date and manufacturer
name.
7.2 Packaging
The products shall be packaged in a closed container lined with a plastic bag; each
package shall be provided with a conformity certificate, indicating batch number and a <......
Related standard:   HG/T 2972-2017  HG/T 2973-2017
   
 
Privacy   ···   Product Quality   ···   About Us   ···   Refund Policy   ···   Fair Trading   ···   Quick Response
Field Test Asia Limited | Taxed in Singapore: 201302277C | Copyright 2012-2019