GB/T 8753.2-2005 PDF English
US$90.00 · In stock · Download in 9 secondsGB/T 8753.2-2005: Anodizing of aluminium and aluminium alloys -- Assessment of quality of sealed anodic oxide coatings -- Part 2: Phosphoric acid/chromic acid test Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Obsolete
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 8753.2-2005 | English | 90 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Anodizing of aluminium and aluminium alloys -- Assessment of quality of sealed anodic oxide coatings -- Part 2: Phosphoric acid/chromic acid test
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 8753.2-2005
GB/T 8753.2-2005: Anodizing of aluminium and aluminium alloys -- Assessment of quality of sealed anodic oxide coatings -- Part 2: Phosphoric acid/chromic acid test
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT8753.2-2005
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 25.220.20
H 21
Replacing GB/T 14952.2-1994
Anodizing of aluminum and its alloys - Assessment of
quality of sealed anodic oxidation coatings - Part 2.
Phosphoric acid/chromic acid test with nitric acid
predip
Issued on. JULY 04, 2005
Implemented on. DECEMBER 01, 2005
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
Standardization Administration of PRC.
Replaced
Table of Contents
Foreword... 3
1 Scope... 5
2 Principle of method... 5
3 Reagents... 5
4 Instruments... 6
5 Specimens... 6
6 Test procedure... 6
7 Presentation of results... 7
8 Test report... 7
Foreword
GB/T 8753 "Anodizing of aluminum and its alloys - Assessment of quality of
sealed anodic oxidation coatings" is divided into 4 parts.
- GB/T 8753.1-2005 Anodizing of aluminum and its alloys - Assessment of
quality of sealed anodic oxidation coatings - Part 1.Measurement of the
loss of mass after immersion in acid solution(s);
- GB/T 8753.2-2005 Anodizing of aluminum and its alloys - Assessment of
quality of sealed anodic oxidation coatings - Part 2.Phosphoric
acid/chromic acid test with nitric acid predip;
- GB/T 8753.3-2005 Anodizing of aluminum and its alloys - Assessment of
quality of sealed anodic oxidation coatings - Part 3.Admittance method;
- GB/T 8753.4-2005 Anodizing of aluminum and its alloys - Assessment of
quality of sealed anodic oxidation coatings - Part 4.Dye spot test with prior
acid treatment.
This part is Part 2 of GB/T 8753.
This part is non-equivalent to EN 12373-7.1999 "Aluminum and aluminum
alloys - Anodizing - Assessment of quality of sealed anodic oxidation coatings
by measurement of the loss of mass after immersion in phosphoric acid/chromic
acid solution with prior acid treatment" (English version). Compared with EN
12373-7.1999, the main content changes are as follows.
- In Chapter 5, ADD that "For cold-sealed materials, they shall be placed for
more than 24 hours before sampling."
From the date of implementation of this part, GB/T 14952.2-1994 "Anodizing of
aluminum and its alloys - Assessment of sealing quality by measurement of the
loss of mass after immersion in acid solution" shall be abolished at the same
time.
Because the "acid dipping method" is not as correlated, to actual use, as the
"phosphoric acid / chromic acid method with nitric acid predip", the "acid dipping
method" is rarely used at home and abroad. European countries have also
abolished their corresponding standards. Therefore, this part specifies the
"phosphoric acid / chromic acid method with nitric acid predip"; meanwhile it
abolishes the "acid dipping method".
The phosphoric acid / chromic acid test with nitric acid predip is a destructive
test.
This part is especially applicable to the anodic oxidation coating of aluminum
alloy for construction use.
This part was proposed by the China Nonferrous Metals Industry Association.
This part shall be under the jurisdiction of the National Nonferrous Metals
Standardization Technical Committee.
Responsible drafting organization of this part. Beijing General Research
Institute of Nonferrous Metals.
Participated drafting organizations of this part. Shenzhen Huajiari Aluminum
Co., Ltd., Guangdong Jianmei Aluminum Profile Factory Co., Ltd.
The main drafters of this part. Zhu Zufang, Li Yongfeng, Yao Liqun, Dai Yuexing,
Tan Qunyan, Guan Yewu, Zhang Jilin.
For this part, the National Non-ferrous Metal Standardization Technical
Committee is responsible for its interpretation.
The previous releases of the abolished standards of this part are as follows.
- GB/T 14952.2-1994.
Anodizing of aluminum and its alloys - Assessment of
quality of sealed anodic oxidation coatings - Part 2.
Phosphoric acid/chromic acid test with nitric acid
predip
1 Scope
This part specifies the method for assessing the quality of sealed anodic
oxidation coatings of aluminum and aluminum alloy, after nitric acid predip AND
etching in phosphoric acid / chromic acid solution, through the loss of mass.
This part applies to both hot-sealed anodic oxidation coating and cold-sealed
anodic oxidation coating.
This part does not apply to the anodic oxidation coating, which was treated by
the following processes.
a) Hard anodic oxidation coating that is usually not sealed;
b) Anodic oxidation coating that has been sealed in a dichromate solution;
c) Anodic oxidation coating produced in chromic acid solution;
d) Anodic oxidation coating after hydrophobic treatment.
2 Principle of method
For the non-sealed anodic oxidation coating, after predip in nitric acid, it will
quickly dissolve after soaking in the phosphoric acid / chromic acid solution,
whilst the well-sealed oxidation coating will not be etched, even after long time
soaking. For this method, according to this principle, the anodic oxidation
coating is pre-dipped in nitric acid, then etched in a phosphoric acid / chromic
acid solution; the sealing quality is evaluated according to the loss of mass.
3 Reagents
3.1 Pre-dip solution. Pipette 650 mL of nitric acid (ρ20 = 1.4 g/mL) into a 1000
mL volumetric flask. Use water to dilute it to the mark.
3.2 Phosphoric acid / chromic acid solution. Dissolve 20 g of chromium trioxide
(CrO3) and 35 mL of phosphoric acid (ρ20 = 1.7 g/mL), in 500 mL of water.
4 Instruments
Analytical balance, which has a sensitivity of 0.1 mg.
5 Specimens
5.1 For hot-sealed materials, it may take specimen at any time after sealing.
For cold-sealed materials, it can take specimen after standing for more than 24
hours.
5.2 From the material to be tested, cut a specimen, which has an effective
surface area of about 10000 mm2 (minimum 5000 mm2). Usually, its mass does
not exceed 200 g.
5.3 For hollow extrusions, it shall take specimen from the end of the profile,
which is covered with anodic oxidation coating on both the inner and outer
surface of the test piece.
6 Test procedure
6.1 Measure the effective surface area of the specimen. Use a dry cloth, to wipe
off the frost spots on the surface of the specimen.
6.2 At room temperature, stir the specimen in a suitable organic solvent for 30
seconds OR wipe off the grease. When using a chlorinating agent, such as
perchloroethylene, for degreasing, the pre-drying shall be carried out in a well-
ventilated fume hood, to prevent inhalation of solvent vapor.
6.4 Immediately weigh the specimen mass (m1), accurate to 0.1 mg.
6.5 Fully immerse the specimen upright in the predip solution (3.1), which has
a temperature of 19 °C ± 1 °C. Keep it for 10 minutes.
6.6 Take the specimen out of the predip solution. First use tap water, then
distilled water, to wash it thoroughly clean.
6.7 Put the specimen upright; completely immerse it into the phosphoric acid /
chromic acid solution (3.2), which was preheated to 38 °C ± 1 °C, to soak it for
15 minutes. The solution can be reused; however, each liter of solution, after
processing 1 x 105 mm2 of oxidation coating, shall be discarded. Do not use
solutions, that have been in contact with materials other than the anodic
oxidation coatings of aluminum and aluminum alloy.
6.8 Take out the specimen from the solution. Use tap water, then deionized
water or distilled water, to wash it clean. After drying according to 6.3,
immediately weigh the mass of the specimen (m2), accurate to 0.1 mg.
7 Presentation of results
The mass loss per unit area is calculated by formula (1).
8 Test report
The test report shall include the following.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 8753.2-2005 be delivered?Answer: The full copy PDF of English version of GB/T 8753.2-2005 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 8753.2-2005_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 8753.2-2005_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 8753.2-2005 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB/T 8753.2-2005?A step-by-step guide to download PDF of GB/T 8753.2-2005_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 8753.2-2005".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|