GB/T 3001-2017 PDF English
US$125.00 · In stock · Download in 9 secondsGB/T 3001-2017: Refractory products -- Determination of modulus of rupture at ambient temperature Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 3001: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 3001-2017 | English | 125 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Refractory products -- Determination of modulus of rupture at ambient temperature
| Valid |
| GB/T 3001-2007 | English | 90 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Refractory products -- Determination of modulus of rupture at ambient temperature
| Obsolete |
| GB/T 3001-2000 | English | 319 |
Add to Cart
|
3 days
|
Shaped refractory products-Determination of modulus of rupture at ambient temperature
| Obsolete |
| GB/T 3001-1982 | English | RFQ |
ASK
|
3 days
|
Test method for modulus of rupture of refractory products at room temperature
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 3001-2017
GB/T 3001-2017: Refractory products -- Determination of modulus of rupture at ambient temperature
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT3001-2017
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 81.080
Q 40
Replacing GB/T 3001-2007
Refractory products - Determination of modulus of rupture
at ambient temperature
(ISO 5014:1997, Dense and insulating shaped refractory products -
Determination of modulus of rupture at ambient temperature, MOD)
ISSUED ON: SEPTEMBER 07, 2017
IMPLEMENTED ON: AUGUST 01, 2018
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Principles ... 5
5 Devices ... 5
6 Specimens ... 6
7 Test steps ... 8
8 Calculation of results ... 8
9 Test report ... 9
Appendix A (Informative) The structural changes of this standard compared with ISO
5014:1997 ... 10
Appendix B (Informative) The technical difference between this standard and ISO
5014:1997 and its reasons ... 11
Refractory products - Determination of modulus of rupture
at ambient temperature
1 Scope
This standard specifies the principle, equipment, specimen, test procedures, result
calculation, test report of the test method for the modulus of rupture of refractory
materials at ambient temperature.
This standard applies to both shaped and unshaped refractory materials.
2 Normative references
The following documents are essential to the application of this document. For the dated
documents, only the versions with the dates indicated are applicable to this document;
for the undated documents, only the latest version (including all the amendments) is
applicable to this standard.
GB/T 4513.5 Monolithic (unshaped) refractory products - Part 5: Preparation and
treatment of test pieces (GB/T 4513.5-2017, ISO 1927-5:2012, MOD)
GB/T 4513.6 Monolithic (unshaped) refractory products - Part 6: Measurement of
physical properties (GB/T 4513.6-2017, ISO 1927-6:2012, MOD)
GB/T 7321 Sample preparation for testing of shaped refractory products
GB/T 8170 Rules of rounding off for numerical values & expression and judgement
of limiting values
GB/T 10325 Shaped refractory products-rule of acceptance, sampling and
inspection (GB/T 10325-2012, ISO 5022:1979, NEQ)
3 Terms and definitions
The following terms and definitions apply to this document.
3.1
Modulus of rupture
The maximum stress, that a refractory strip specimen of a certain size can withstand,
on a three-point bending device.
4 Principles
At room temperature, stress is applied to the specimen at a constant loading rate, until
the specimen breaks.
5 Devices
5.1 Loading device
5.1.1 The loading device shall have three blades, where the lower two blades support
the specimen, AND the upper blade apply load (see Figure 1). The radius of curvature
of the three cylindrical blades shall comply with the requirements in Table 1. The length
of the blade shall be at least 5 mm larger than the width (b) of the specimen (see Figure
2). The contact lines between the three blades and the specimen shall be parallel to each
other AND perpendicular to the side of the pressure surface of the specimen, in the
length direction. The two lower blades shall be located on an intermediate support block,
whose bottom surface is part of a cylindrical surface, so that each lower blade can be
adjusted independently, when the specimen is slightly deflected in the vertical plane
(see Figure 2). One lower blade can also be fixed, so that the other lower blade and the
upper blade can be adjusted on the vertical plane. The distance between the two blades
is as shown in Table 1. The upper blade is located in the middle of the two lower blades,
which has a deviation within 2 mm.
5.1.2 The loading device shall be able to load uniformly, in the middle of the specimen
at a constant rate; have an instrument capable of recording or indicating the breaking
load. The error of the force indication shall be within ±2%.
5.2 Electric blast drying oven
It can be controlled at 110 °C ± 5 °C.
5.3 Vernier calipers
The division value is not more than 0.05 mm.
7 Test steps
7.1 Dry the specimen in a drying oven (5.2), at 110 °C ± 5 °C, to constant weight. Cool
it to room temperature, in a desiccator. If used in chemically bonded or tar bonded
bricks, these products are subject to some form of prior heat treatment. The specific
provisions of such pre-heat treatment conditions are beyond the scope of this standard
AND must be determined, through consultation between relevant parties, meanwhile
indicated in the test report.
Note: For other specimens that are not suitable for drying at 110 °C ± 5 °C, the drying conditions
should be determined through consultation with relevant parties.
7.2 Measure the width and height of the middle part of each specimen, accurate to 0.1
mm. Measure the distance between the lower blades, accurate to 0.5 mm.
7.3 Place the specimen symmetrically on the lower edge of the loading device (5.1). If
the specimen is a whole brick, the pressure surface shall be the formed pressure surface.
If the specimen is cut from a brick, the pressure side shall be the formed pressure surface
of the original brick.
7.4 Apply a load vertically to the specimen at room temperature until it breaks, at a
loading rate of:
a) 0.15 MPa/s ± 0.015 MPa/s for dense refractory products;
b) 0.05 MPa/s ± 0.005 MPa/s for insulation and refractory products.
7.5 Record the load (Fmax) at which the specimen breaks.
8 Calculation of results
8.1 The modulus of rupture at ambient temperature is calculated by formula (1):
Where:
αF - Modulus of rupture at ambient temperature, in megapascals (MPa);
Fmax - The maximum pressure applied to the specimen, in Newton (N);
LS - The distance between the lower blades, in millimeters (mm);
b - The width of the specimen, in millimeters (mm);
h - The height of the specimen, in millimeters (mm).
8.2 For shaped products, if it is a whole brick, the measured value of one brick is the
result of this specimen.
8.3 For the cut specimen, when the specimen cut from the sample is 1 piece, the single
value represents the result of this specimen. When the specimen cut from the sample is
more than 1 piece, use the single value and the calculated average value to indicate the
result of this specimen.
8.4 The result shall be rounded off according to GB/T 8170, with one decimal place
retained.
9 Test report
The test report shall include the following:
a) The name of the laboratory;
b) Test items;
c) Test date;
d) Implemented standards, such as "in accordance with GB/T 3001-2017";
e) Identification of test bricks (manufacturer, variety, brick type, batch number);
f) Test sample name, quantity, number of specimens;
g) Whether the specimen has been pretreated (drying, heat treatment temperature,
holding time, etc.);
h) Specimen size;
i) Loading rate (MPa/s);
j) When more than one specimen is cut from each sample, report the individual and
average values of the modulus of rupture of each specimen in each sample; when
testing with a whole brick, report the modulus of rupture of each sample.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 3001-2017 be delivered?Answer: The full copy PDF of English version of GB/T 3001-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 3001-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 3001-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 3001-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 3001-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 3001-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 3001-2017?A step-by-step guide to download PDF of GB/T 3001-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 3001-2017".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|