GB/T 29459.1-2012 PDF English
US$130.00 · In stock · Download in 9 secondsGB/T 29459.1-2012: Small punch test methods of metallic materials for in-service pressure equipment - Part 1: General requirements Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 29459.1-2012 | English | 130 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Small punch test methods of metallic materials for in-service pressure equipment - Part 1: General requirements
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 29459.1-2012
GB/T 29459.1-2012: Small punch test methods of metallic materials for in-service pressure equipment - Part 1: General requirements
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT29459.1-2012
GB
NATIONAL STANDARD OF
THE PEOPLE’S REPUBLIC OF CHINA
ICS 77.040.10
H 22
Small punch test methods of metallic materials
for in-service pressure equipments –
Part 1. General requirements
Issued on: DECEMBER 31, 2012
Implemented on: JULY 1, 2013
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration Committee.
Table of Contents
Foreword ... 3
Introduction ... 4
1 Scope ... 5
2 Normative references ... 5
3 Terms, definitions and symbols ... 5
4 Specimen ... 8
5 Test device ... 9
6 Test report ... 10
Foreword
GB/T 29459 Small punch test methods of metallic materials for in-service
pressure equipments consists of the following two parts.
- Part 1. General requirements;
- Part 2. Method of test for tensile properties at room temperature.
This Part is the first part of GB/T 29459.
This Part was drafted in accordance with the rules given in GB/T 1.1-2009.
This Part mainly referred to relative technical content of CWA 15627 Small
punch test methods of metallic materials and was formulated based on the
combination of the actual situation of China and research results.
This Part was proposed by and shall be shall be under the jurisdiction of
National Technical Committee on Boiler and Pressure Vessel of Standardization
Administration of China (SAC/TC 262).
The drafting organizations of this Part. China Special Equipment Inspection and
Research Institute, East China University of Science and Technology, Nanjing
University of Technology, Nanjing University of Technology, Jiangsu Special
Equipment Safety Supervision and Inspection Institute.
Main drafters of this Part. Xu Tong, Sun Liang, Jia Guodong, Guan Kaishu,
Wang Zhiwen, Ling Xiang, Yuan Biao, Qian Gong, Zhang Xian, Li Liqun, Ding
Keqin.
Small punch test methods of metallic materials
for in-service pressure equipments –
Part 1. General requirements
1 Scope
This Part of GB/T 29459 specifies general requirements for small punch test
methods of metallic materials for in-service pressure equipment.
This Part is applicable to metallic materials for pressure equipment.
2 Normative references
The following referenced documents are indispensable for the application of
this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any
amendments) applies.
GB/T 16825.1-2008, Verification of static uniaxial testing machines - Part 1.
Tension/compression testing machines - Verification and calibration of the
force-measuring system
3 Terms, definitions and symbols
3.1 Terms and definitions
The following terms and definitions apply to this document.
3.1.1 small punch test; SPT
a test method for mechanical properties which takes micro-sheet sample as test
object; this method fixes the edge of the sheet specimen; the center of the
specimen is loaded with a spherical punch at the top of the punch in a
mechanically loading manner; the mechanical properties of the composites are
determined by experimental data association. The schematic diagram of the
test device is shown in Figure 1.
3.1.2 load; F
the mechanical force exerted by the plunger on the specimen
3.1.9 sample
a sheet of material removed from the equipment
3.1.10 specimen
the sheet material which meets small punch test requirements
3.2 Symbols
d1 - specimen diameter, in millimeters (mm);
d2 - lower fixture aperture, in millimeters (mm);
E - elastic modulus, in megapascals (MPa);
F - load, in newtons (N);
h - specimen thickness, in millimeters (mm);
r - radius of the punch or ball, in millimeters (mm);
T - test temperature, in Celsius degrees (°C);
t - test time, in seconds (s);
u - punch displacement, in millimeters (mm);
V - test speed (movement speed of punch under pressure), in millimeters per
second (mm/s).
4 Specimen
4.1 Sampling
4.1.1 General requirements
Sampling should prevent overheating and work hardening which shall affect the
mechanical properties of the specimen. The specimen shall not contain any
cracks and other macroscopic defects. And it should ensure that the cut pieces
have integrity.
4.1.2 Sampling position
The cutting of test piece should avoid the corrosion layer (as shown in Figure
3).
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 29459.1-2012 be delivered?Answer: The full copy PDF of English version of GB/T 29459.1-2012 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 29459.1-2012_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 29459.1-2012_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 29459.1-2012 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB/T 29459.1-2012?A step-by-step guide to download PDF of GB/T 29459.1-2012_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 29459.1-2012".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|