GB/T 2493-1995 (GB/T2493-1995, GBT 2493-1995, GBT2493-1995)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| GB/T 2493-1995 | English | 95 |
Add to Cart
|
0--9 seconds. Auto-delivery
|
Rotation test of grinding wheel strength
| Obsolete |
GB/T 2493-1995
|
| GB/T 2493-2023 | English | 329 |
Add to Cart
|
4 days [Need to translate]
|
Test method for rotating strength of abrasive products
| Valid |
GB/T 2493-2023
|
Newer version: GB/T 2493-2023 Standards related to: GB/T 2493-2023
| Standard ID | GB/T 2493-1995 (GB/T2493-1995) | | Description (Translated English) | Rotation test of grinding wheel strength | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | J43 | | Classification of International Standard | 25.100.70 | | Word Count Estimation | 2,221 | | Date of Issue | 1995/12/1 | | Date of Implementation | 1996/8/1 | | Older Standard (superseded by this standard) | GB 2493-1984 | | Drafting Organization | Zhengzhou Institute of abrasive grinding abrasive | | Administrative Organization | National Standardization Technical Committee Abrasives | | Proposing organization | Ministry of Machinery Industry of the People Republic of China | | Issuing agency(ies) | State Bureau of Technical Supervision | | Summary | This standard specifies test methods for turning the wheel. This standard applies to all kinds of wheel binding agents and other tests require rotating abrasive. | GB/T 2493-1995
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 25.100.70
J 43
Rotation test of grinding wheel strength
ISSUED ON: DECEMBER 01, 1995
IMPLEMENTED ON: AUGUST 01, 1996
Issued by: State Bureau of Technical Supervision
Table of Contents
1 Scope ... 3
2 Test equipment ... 3
3 Test conditions and methods ... 3
Appendix A Chuck and partition for rotation test (Supplementary) ... 6
Additional information: ... 8
Rotation test of grinding wheel strength
1 Scope
This standard specifies the rotation test method of the grinding wheel strength.
This standard applies to grinding wheels with various bonding agents and other
abrasive tools that need to be subject to rotation test.
2 Test equipment
2.1 The rotation test is carried out on a special rotation testing machine
according to the diameter, quality and maximum working speed of the grinding
wheel.
2.2 The spindle speed error of the rotation testing machine shall not be more
than 3%.
2.3 The radial runout of the main shaft of the rotation testing machine is not
more than 0.07 mm. The measurement location is the middle of the mandrel.
2.4 The rotation test machine shall be equipped with a time relay, to ensure that
when the spindle speed reaches the test speed, the speed will be reduced after
maintaining a specified period of time.
2.5 The noise level of the rotation testing machine shall not exceed 85 dB(A) at
no load.
2.6 The protective cover of the rotation testing machine shall be firm and safe.
2.7 The rotation testing machine shall be inspected regularly.
3 Test conditions and methods
3.1 The rotation test shall be carried out according to the following method at
the maximum working speed as marked on the grinding wheel.
For grinding wheels with a maximum working speed of less than or equal to 50
m/s, the rotation test is performed at 1.6 times the maximum working speed;
after reaching to the maximum speed, it is maintained for 30 s.
For grinding wheels with a maximum working speed greater than 50 m/s, the
rotation test is performed at 1.5 times the maximum working speed; after
reaching to the maximum speed, it is maintained for 30 s.
Note: If there are other provisions for the rotation test method in the product
standard, the product standard shall be implemented.
3.2 It is allowed to install multiple grinding wheels on the main shaft of the
rotation testing machine at the same time; different grinding wheels shall be
separated by a partition. The outer diameter of the partition and the width of the
pressing surface are the same as the chuck.
3.3 The grinding wheel as installed on the main shaft of the rotation testing
machine shall be fastened by chucks at both ends.
3.4 When the hole diameter of the grinding wheel is larger than the outer
diameter of the main shaft of the testing machine, a shaft sleeve is allowed.
3.5 Grinding wheel chuck
3.5.1 The shape and dimensions of the grinding wheel chuck and the partition
are as shown in Appendix A (Supplementary).
3.5.2 For the grinding wheel whose outer diameter and the diameter are not
listed in Appendix A (Supplementary), the outer diameter of the chuck shall
conform to formula (1)
Where:
Df - Outer diameter of chuck, mm;
D - Outer diameter of grinding wheel, mm;
H - Aperture of grinding wheel, mm.
3.5.3 The outer diameter of the cymbal-shaped grinding wheel chuck shall
conform to formula (2); the other dimensions shall be in accordance with
Appendix A, Table A1.
Where:
Df - Outer diameter of chuck, mm;
D1 - The inner bottom diameter of grinding wheel, mm.
...
|