GB/T 20936.4-2017 PDF English
US$435.00 · In stock · Download in 9 secondsGB/T 20936.4-2017: Gas detectors for explosive atmospheres -- Part 4: Performance requirements of open path detectors for flammable gases Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 20936.4: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 20936.4-2017 | English | 435 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Gas detectors for explosive atmospheres -- Part 4: Performance requirements of open path detectors for flammable gases
| Valid |
| GB 20936.4-2008 | English | 319 |
Add to Cart
|
3 days
|
Electrical apparatus for the detection and measurement of flammable gases -- Part 4: Performance requirements for group II apparatus indicating a volume fraction up to 100% gas
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 20936.4-2017
GB/T 20936.4-2017: Gas detectors for explosive atmospheres -- Part 4: Performance requirements of open path detectors for flammable gases
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT20936.4-2017
GB
NATIONAL STANDARD OF THE
PEOPLE'S REPUBLIC OF CHINA
ICS 29.260.20
K 35
Gas detectors for explosive atmospheres - Part 4:
Performance requirements of open path detectors for
flammable gases
(IEC 60079-29-4:2009, Explosive atmospheres - Part 29-4: Gas detectors -
Performance requirements of open path detectors for flammable gases, MOD)
ISSUED ON: DECEMBER 29, 2017
IMPLEMENTED ON: JULY 1, 2018
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative references ... 6
3 Terms and definitions ... 7
4 General requirements ... 11
4.1 Detection equipment ... 11
4.2 Construction ... 12
4.3 Software-controlled equipment ... 14
5 Test requirements ... 16
5.1 Introduction ... 16
5.2 General requirements for tests ... 17
5.3 Normal conditions for test ... 21
5.4 Test methods ... 23
6 Field verification equipment ... 36
7 Information for use ... 37
7.1 Labelling and marking ... 37
7.2 Instruction manual ... 37
Appendix A (Informative) Water vapour test apparatus ... 40
Appendix B (Informative) Degree of consistency between the various parts of GB/T
3836 and that of IEC 60079 ... 41
References ... 43
Foreword
GB/T 20936 Gas detectors for explosive atmospheres is divided into several parts:
-- Part 1: Performance requirements of detectors for flammable gases;
-- Part 2: Selection, installation, use and maintenance of detectors for flammable
gases and oxygen;
-- Part 3: Guidance on functional safety of fixed gas detection systems;
-- Part 4: Performance requirements of open path detectors for flammable gases;
...
This part is Part 4 of GB/T 20936.
This part was drafted in accordance with the rules given in GB/T 1.1-2009.
This part is modified in relation to IEC 60079-29-4:2009 Explosive atmospheres - Part
29-4: Gas detectors - Performance requirements of open path detectors for flammable
gases with the use of the redrafted method.
Compared with IEC 60079-29-4:2009, the following structural adjustments have been
made in this part:
-- 4.3.1 General rule is added, and the numbers of subsequent articles are postponed.
The main technical differences between this part and IEC 60079-29-4:2007 and their
reasons are as follows:
-- Regarding normative references, adjustments with technical differences have
been made in this part to adapt to Chinese technical conditions. The adjustments
are reflected in Chapter 2 "Normative references". The specific adjustments are
as follows:
IEC 60079(all parts) is replaced with GB/T 3836(all parts). The degree of
consistency between the parts of the two standards is shown in Appendix
B;
IEC 60079-0 is replaced with GB 3836.1, IEC 60825-1 is replaced with
GB 7247.1, IEC 61000-4-1 is replaced with GB/T 17626.1, IEC 61000-4-
3 is replaced with GB/T 17626.3, and IEC 60079-29-1 is replaced with
GB/T 20936.1-2017.
The following editorial changes have been made to this part:
Gas detectors for explosive atmospheres - Part 4:
Performance requirements of open path detectors for
flammable gases
1 Scope
This part of GB/T 20936 specifies performance requirements of equipment for the
detection and measuring of flammable gases or vapours in ambient air by measuring
the spectral absorption by the gases or vapours over extended optical paths, ranging
typically from one metre to a few kilometres.
Such equipment measures the integral concentration of the absorbing gas over the
optical path in units such as LEL.m for flammable gases.
NOTE 1: Actual values of concentration can be deduced only where it can be established that the
concentration is uniform over the optical path, for example in very short optical paths (< 100 mm). In
such cases, the equipment is within the scope of GB/T 20936.1-2017.
NOTE 2: This part is based on present absorption techniques using infrared radiation. Other techniques
and applications may require additional test considerations (e.g., pressure test).
Equipment falling within the scope of this part is classified by the following types:
Type 1: an optical transmitter and receiver, located at either end of a path through the
atmosphere to be monitored.
Type 2: an optical transceiver (i.e., combined transmitter and receiver) and a suitable
reflector, which may be a topographic feature or a retroreflector, located at either end
of a path through the atmosphere to be monitored.
This part is also applicable when an equipment manufacturer makes any claims
regarding any special features of construction or superior performance that exceed the
minimum requirements of this part. All such claims shall be verified and the test
procedures should be extended or supplemented, where necessary, to verify the claimed
performance. The additional tests shall be agreed upon between the manufacturer and
the test laboratory and identified and described in the test report.
This part does not apply to any of the following:
a) equipment intended to provide range resolution of gas concentration (e.g.,
Light direction and ranging (LIDAR));
5.2.2 Constructional checks
Equipment shall be checked to ensure that the constructional requirements of 4.2 are
satisfied.
5.2.3 Preparation of samples
The sample equipment shall, as nearly as possible, be prepared and mounted as for
typical service using the manufacturer's brackets and fittings, including all necessary
interconnections and initial adjustments, and in accordance with the manufacturer's
written instructions.
For Type 2 equipment designed for use with a natural topographical feature, such as a
reflector, that feature shall be represented by a plane diffusing surface set normal to the
optical axis of the measured volume.
The surface shall be large enough in extent to intercept the whole of the measured
volume and its albedo shall lie between 0.1 and 0.3 over the wavelength range employed
by the equipment.
For equipment without an indication of measurement, for example, in alarm only
apparatus, the output of equipment from a test point shall be connected to a
continuously recording output display device.
5.2.4 Equipment for calibration and test
5.2.4.1 Use of gas cells
The test facility shall be designed such that the test gas in individual cells can be
changed and that when using the equipment, such as shown in Figure 1, the cells can
be exchanged sufficiently quickly in order that transient obscuration during the
exchange by the walls or window retaining structure shall not create a "beam blocked"
condition. The transverse dimension of the cells shall be large enough not to cause
partial blockage of the beam.
NOTE 1: The test described in 5.4.8 and 5.4.21 may require cells of large dimensions or the use of an
alternate gas simulation filter.
Cells shall be located as close as possible to the receiving aperture of the equipment
having regard to minimizing unwanted effects on the equipment of reflections from the
cell on the receiver, and the cells shall not cause partial blockage of the beam.
The characteristics (e.g., material, thickness and flatness) and inclination of the
windows of the cells shall be chosen to minimize the effects of reflection, distortion and
attenuation of the beam over the effective bandwidth of the measuring radiation. Signal
errors arising from variations of attenuation with wavelength in the window material
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 20936.4-2017 be delivered?Answer: The full copy PDF of English version of GB/T 20936.4-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 20936.4-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 20936.4-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 20936.4-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 20936.4-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 20936.4-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 20936.4-2017?A step-by-step guide to download PDF of GB/T 20936.4-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 20936.4-2017".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|