GB/T 18983-2017 PDF English
US$85.00 · In stock · Download in 9 secondsGB/T 18983-2017: Wire for quenched and tempered springs Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 18983: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 18983-2017 | English | 85 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Wire for quenched and tempered springs
| Valid |
| GB/T 18983-2003 | English | 105 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Oil-hardened and tempered stell wire for mechanical springs
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 18983-2017
GB/T 18983-2017: Wire for quenched and tempered springs---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT18983-2017
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.140.65
H 49
Replacing GB/T 18983-2003
Wire for Quenched and Tempered Springs
(ISO 8458-3.2002, Steel Wire for Mechanical Springs –
Part 3.Oil-Hardened and Tempered Wire, NEQ)
Issued on. JULY 12, 2017
Implemented on. APRIL 01, 2018
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of PRC.
Table of Contents
Foreword... 3
1 Scope... 5
2 Normative References... 5
3 Classification and Code... 7
4 Ordering Contents... 7
5 Diameter, Appearance and Permissible Deviation... 8
6 Manufacturing Method... 8
7 Technical Requirements... 9
8 Test Methods... 14
9 Inspection Rules... 15
10 Package, Mark and Quality Certificate... 16
Appendix A (Informative) Correspondence between Codes and Steel Grades
... 18
Foreword
This Standard was drafted as per the rules specified in GB/T 1.1-2009.
This Standard replaced GB/T 18983-2003 Oil-Hardened and Tempered Steel Wire for
Mechanical Springs. Compared with GB/T 18983-2003, this Standard has the major
changes as follows.
--- Increase “GB/T 4336, GB/T 13298, GB/T 20123, GB/T 20125” to the Normative
References;
--- Increase “ultra-high-strength’ level to the Classification and Code;
--- Modify the diameter range;
--- Increase the components to the new types of TDSiCr-B, TDSiCr-C and VDSiCrV
to the chemical compositions;
--- Modify “maximum surface decarburization allowable depth”;
--- Increase the mechanical property indexes of TDSiCr-B, TDSiCr-C to “mechanical
properties of steel wires in static grade and medium fatigue grade”;
--- Increase the mechanical property indexes of VDSiCrV to “mechanical properties
of steel wire in high fatigue grade”;
--- Modify “allowable maximum depth of surface defect”; add description of the acid
leaching test method.
This Part was prepared by using the redrafted law and referring to ISO 8458-3.2002
Steel Wire for Mechanical Springs – Part 3.Oil-Hardened and Tempered Wire; the
degree of consistency with ISO 8458-3.2002 is not equivalent.
This Standard was proposed by China Iron and Steel Industry Association.
This Standard shall be under the jurisdiction of National Technical Committee for
Standardization of Steel (SAC/TC 183).
Drafting organizations of this Standard. Sinosteel Zhengzhou Research Institute of
Steel Wire Products Co., Ltd., Tianjin Metallurgical Group Zhongxing Shengda Steel
Co., Ltd., Guangzhou Orsa Wire Science & Technology Co., Ltd., Baosteel Group
Nantong Wire Products Co., Ltd., Jiangsu Shenwang Group Cable Co., Ltd., Taibo
Steel Co., Ltd., and China Metallurgical Information and Standardization Institute.
Chief drafting staffs of this Standard. Zhang Fengshan, Jiang Ling, Zhang Yongbo,
Xing Xianqiang, Lin Xiuyan, Zhou Jianhua, Ren Cuiying, Wang Lingjun, Huang
Jianming, Wang Wenxi, Zhang Jun, Meng Zhaoxian, Zhang Honglong, Cui Tongquan,
Zhang Weidong, Li Changchun, Li Zhaoming, and Zhang Xiaoguang.
The historical edition replaced by this Standard is as follows.
--- GB/T 18983-2003.
Wire for Quenched and Tempered Springs
1 Scope
This Standard specifies the classification and code, ordering content, diameter,
appearance and permissible deviation, manufacturing method, technical requirements,
test methods, inspection rules, package, mark and quality certificate of wire for
quenched and tempered springs (hereinafter referred to as steel wire).
This Standard is applicable to the carbon and low alloy quenched-tempered circular-
section steel wire used for manufacturing various mechanical springs.
2 Normative References
The following documents are essential to the application of this document. For the
dated documents, only the versions with the dates indicated are applicable to this
document; for the undated documents, only the latest version (including all the
amendments) are applicable to this document.
GB/T 222 Method of Sampling Steel for Determination of Chemical Composition
and Permissible Variations for Product Analysis
GB/T 223.5 Methods for Chemical Analysis of Iron, Steel and Alloy - The Reduced
Molybdosilicate Spectrophotometric Method for the Determination of Acid-Soluble
Silicon Content
GB/T 223.11 Iron, Steel and Alloy - Determination of Chromium Content - Visual
Titration or Potentiometric Titration Method
GB/T 223.13 Methods for Chemical Analysis of Iron, Steel and Alloy - The
Ammonium Ferrous Sulfate Titration Method for the Determination of Vanadium
Content
3 Classification and Code
3.1 Classification
3.1.1 The steel wire can be classified into three types, namely, static-state, medium
fatigue and high fatigue as per the working state.
3.2 Code
The classification, code and diameter range of the steel wire can refer to Table 1.
3.3 Mark example
Grade-VDSiCr steel wire with diameter of 3.0mm is marked as.
VDSiCr-3.0-GB/T 18983.
4 Ordering Contents
The purchasing list or contract that orders products as per this Standard shall include
the following contents.
5 Diameter, Appearance and Permissible Deviation
5.1 Diameter
5.2 Appearance
The appearance of the steel wire shall be regular and be free of the bending that may
affect the use.
6 Manufacturing Method
The steel wire is made through cold-drawing the wire rod and then quenched and
tempered it. The ultra-high-strength VDSiCrV steel wire shall be made through peeling
and flaw-detection.
7 Technical Requirements
7.1 Chemical compositions
7.1.1 The chemical compositions (smelting analysis) of steel for steel wire shall meet
the requirements of Table 3.The commonly used steel grades in China can refer to
Table A.1.
7.2 Surface decarburization
The surface of the steel wire shall be free of full decarburization layer; and the
allowable depth of the decarburization layer shall be no greater than 1.0%d; and a
maximum of 0.15mm.
7.3 Non-metallic inclusion
Inspect the non-metallic inclusion of the steel wire; its level of conformity shall be
negotiated by the purchaser and the supplier; indicated in the contract; if it is not
indicated in the contract, the level of conformity shall be confirmed by the supplier.
7.5 Mechanical properties
7.5.1 The tensile strength and reduction of area of the steel wire shall meet the
requirements of Table 4, and Table 5.
7.5.2 Steel wire with nominal diameter greater than 1.00mm shall be measured for
reduction of area.
7.5.3 Through the agreement, steel wire can also use other control ranges of tensile
strength.
7.5.4 The allowable fluctuation range of the tensile strength of steel wire in a plate or
shaft shall be as follows.
7.6 Process performance
7.6.1 Wrapping test
The requirements for wrapping test are as follows.
7.6.3 Bending test
The requirements for bending test are as follows.
7.6.4 Winding test
According to the requirements of the purchaser, the steel wire with nominal diameter
no greater than 0.70mm shall take the winding test.
7.7 Surface quality
7.7.1 The surface of the steel wire shall be smooth, and there shall be no defects
such as cracks, folds, scabs, and continuous pockmarks; allow the minor scratches,
pits and etc. to exist; their depths shall conform to the provisions of Table 7.
Table 7 -- Allowable Maximum Depth for Surface Defect
7.8 Flaw detection
The ultra-high-strength steel wire shall take the eddy current flaw detection; the
detection depth and the number of detection marks shall be negotiated between the
supplier and the purchaser.
7.9 Particular requirements
According to the requirements of the purchaser, through the negotiation between the
supplier and the purchaser, other particular requirements can be proposed, and
indicated in the contract.
8 Test Methods
The inspection items, sampling quantities, and test methods of steel wire shall be
performed as per the provisions of Table 8.
9 Inspection Rules
9.1 Inspection and acceptance
9.1.1 The inspection of steel wire shall be performed by the quality supervision
department of the supplier.
9.2 Batching rules
The steel wire batch consists of the steel wires with the same grade, the same furnace
(tank) number, the same diameter, and the same technical requirements.
9.3 Reinspection and judgment rules
The reinspection and judgment rules of the steel wire shall be performed as per the
provisions of GB/T 2103.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 18983-2017 be delivered?Answer: The full copy PDF of English version of GB/T 18983-2017 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 18983-2017_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18983-2017_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 18983-2017 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 18983-2017?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 18983-2017 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 18983-2017?A step-by-step guide to download PDF of GB/T 18983-2017_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 18983-2017".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|